Streszczenie treści zawartej na stronie nr. 1
Streszczenie treści zawartej na stronie nr. 2
CIO-DIO48H Digital Input/Output Board User’s Guide Document Revision 1, December, 2006 © Copyright 2006, Measurement Computing Corporation
Streszczenie treści zawartej na stronie nr. 3
Your new Measurement Computing product comes with a fantastic extra — Management committed to your satisfaction! Refer to www.mccdaq.com/execteam.html for the names, titles, and contact information of each key executive at Measurement Computing. Thank you for choosing a Measurement Computing product—and congratulations! You own the finest, and you can now enjoy the protection of the most comprehensive warranties and unmatched phone tech support. It’s the embodiment of our mission: To pr
Streszczenie treści zawartej na stronie nr. 4
Trademark and Copyright Information TracerDAQ, Universal Library, Harsh Environment Warranty, Measurement Computing Corporation, and the Measurement Computing logo are either trademarks or registered trademarks of Measurement Computing Corporation. Windows, Microsoft, and Visual Studio are either trademarks or registered trademarks of Microsoft Corporation LabVIEW is a trademark of National Instruments. CompactFlash is a registered trademark of SanDisk Corporation. XBee and XBee-PRO are
Streszczenie treści zawartej na stronie nr. 5
Table of Contents Preface About this User's Guide .......................................................................................................................6 What you will learn from this user's guide.........................................................................................................6 Conventions in this user's guide .........................................................................................................................6 Where to find m
Streszczenie treści zawartej na stronie nr. 6
Preface About this User's Guide What you will learn from this user's guide This user's guide explains how to install, configure, and use the CIO-DIO48H board so that you get the most out of its analog output features. This user's guide also refers you to related documents available on our web site, and to technical support resources. Conventions in this user's guide The following conventions are used in this manual to convey special information: For more information on … Text presente
Streszczenie treści zawartej na stronie nr. 7
Chapter 1 Introducing the CIO-DIO48H Overview: CIO-DIO48H features The CIO-DIO48H provides 48-bits of digital I/O. The I/O is organized into two 24-bit groups based on an 82C55 mode 0 emulation. Each 24-bit group is divided into three eight-bit ports labeled An, Bn and Cn, where n is either "1" for FIRSTPORT or "2" for SECONDPORT. Port C can be split into two four-bit nibbles — Port C-HI and Port C-LO. Each of these ports may be individually programmed as input or output. All digital in
Streszczenie treści zawartej na stronie nr. 8
Chapter 2 Installing the CIO-DIO48H What comes with your CIO-DIO48H shipment? The following items are shipped with the CIO-DIO48H. Hardware CIO-DIO48H Additional documentation In addition to this hardware user's guide, you should also receive the Quick Start Guide (available in PDF at www.mccdaq.com/PDFmanuals/DAQ-Software-Quick-Start.pdf). This booklet supplies a brief description of the software you received with your CIO-DIO48H and information regarding installation of that soft
Streszczenie treści zawartej na stronie nr. 9
CIO-DIO48H User's Guide Installing the CIO-DIO48H Unpacking the CIO-DIO48H As with any electronic device, you should take care while handling to avoid damage from static electricity. Before removing the CIO-DIO48H from its packaging, ground yourself using a wrist strap or by simply touching the computer chassis or other grounded object to eliminate any stored static charge. If any components are missing or damaged, notify Measurement Computing Corporation immediately by phone, fax, or e-ma
Streszczenie treści zawartej na stronie nr. 10
CIO-DIO48H User's Guide Installing the CIO-DIO48H Disregard the numbers printed on the switch When setting the base address, refer to the numbers printed in white on the printed circuit board. PC I/O Address Summary Hex Range Function Hex Range Function 000-00F 8237 DMA #1 2C0-2CF EGA 020-021 8259 PIC #1 2D0-2DF EGA 040-043 8253 TIMER 2E0-2E7 GPIB (AT) 060-063 8255 PPI (XT) 2E8-2EF SERIAL PORT 060-064 8742 CONTROLLER (AT) 2F8-2FF SERIAL PORT 070-071 CMOS RAM & NMI MASK (AT) 300-30F PRO
Streszczenie treści zawartej na stronie nr. 11
CIO-DIO48H User's Guide Installing the CIO-DIO48H Connecting the board for I/O operations Connectors, cables – main I/O connector The table below lists the board connector, applicable cables, and compatible accessory products. Board connector, cables, and accessory equipment Connector type 50-pin shrouded male header Compatible cables C50FF-x Compatible accessory products CIO-TERM100 with the C50FF-x cable CIO-SPADE50 CIO-MINI50 SSR-RACK24, SSR-RACK48 CIO-ERB24, CIO-ERB48 Pinout – m
Streszczenie treści zawartej na stronie nr. 12
CIO-DIO48H User's Guide Installing the CIO-DIO48H Cabling The red stripe 2 1 2 1 identifies pin # 1 50 49 50 49 50-pin Female 50-pin Female IDC Connector IDC connector Figure 3. C50FF-x cable Field wiring, signal termination, and conditioning You can use the following cabling, screw termination, and signal conditioning products with the CIO-DIO48H. CIO-TERM100 – 100-pin screw terminal board (daisy-chained 50-pin IDC connectors). Details on this product are available on our web site at
Streszczenie treści zawartej na stronie nr. 13
Chapter 3 Functional Details 82C55 emulation The CIO-DIO48H emulates the 82C55 chip. The 82C55 emulation initializes all ports as inputs on power-up and reset. A TTL input is a high impedance input. If you connect another TTL input device to the output, it could be turned on or off every time the board is reset. To establish a consistent TTL level at power-up, use resistors tied to either +5V (pull-up) or ground (pull- down). There are open locations for pull-up and pull-down resistor p
Streszczenie treści zawartej na stronie nr. 14
CIO-DIO48H User's Guide Functional Details +5 VDC +5 VDC 2.2 K SIP Dot COM 2.2 K SIP HI HI n7 n7 n6 n6 n5 n5 Digital Digital n4 n4 I/O I/O Port n3 Port n3 n2 n2 n = A, B, or C n = A, B, or C n1 n1 n0 n0 COM LO LO (GND) (GND) Dot 2.2 K SIP installed for pull-up 2.2 K SIP installed for pull-down Figure 5. Pull-up and pull-down resistor SIPs schematic To pull-up lines, orient the SIP with the common pin (dot) toward the HI end; to pull-down, install the resistor with the common pin in the
Streszczenie treści zawartej na stronie nr. 15
CIO-DIO48H User's Guide Functional Details CIO-DIO48H IN OUT CIO-ERB24 or SSR-RACK24 IN OUT CIO-ERB24 or SSR-RACK24 Figure 6. CIO-DIO48H to CIO-ERB24 or SSR-RACK24 daisy chain The 24 digital I/O bits on pins 25 to 48 (base address +0 through +2) control the first relay board. The 24 digital I/O bits on pins 1 to 24 control the second relay/SSR board on the daisy chain. Use the C50FF-x cable for interconnections. You can also use SSR-RACK48 or the CIO-ERB48 series relay boards. 15
Streszczenie treści zawartej na stronie nr. 16
Chapter 4 Programming and Developing Applications After following the installation instructions in Chapter 2, your board should now be installed and ready for use. In general there may be no correspondence among registers for different boards. Software written at the register level for other models will not function correctly with your board. Programming languages Measurement Computing's Universal Library provides access to board functions from a variety of Windows programming languages
Streszczenie treści zawartej na stronie nr. 17
Chapter 5 Specifications Typical for 25 °C unless otherwise specified. Specifications in italic text are guaranteed by design. Digital input/output Table 1. DIO specifications Digital type 8255 mode 0 emulation Output: 74S244 Input: 74LS373 Configuration 4 banks of 8, 4 banks of 4, programmable by bank as input or output Number of channels 48 I/O Output high 2.4 volts min @ -15 mA Output low 0.5 volts max @ 64 mA Input high 2.0 volts min, 7 volts absolute max Input low 0.8 volt
Streszczenie treści zawartej na stronie nr. 18
CIO-DIO48H User's Guide Specifications Table 5. Main connector pin out Pin Signal name Pin Signal name 50 GND 49 +5V 48 FIRSTPORTC Bit 0 47 FIRSTPORTC Bit 1 46 FIRSTPORTC Bit 2 45 FIRSTPORTC Bit 3 44 FIRSTPORTC Bit 4 43 FIRSTPORTC Bit 5 42 FIRSTPORTC Bit 6 41 FIRSTPORTC Bit 7 40 FIRSTPORTB Bit 0 39 FIRSTPORTB Bit 1 38 FIRSTPORTB Bit 2 37 FIRSTPORTB Bit 3 36 FIRSTPORTB Bit 4 35 FIRSTPORTB Bit 5 34 FIRSTPORTB Bit 6 33 FIRSTPORTB Bit 7 32 FIRSTPORTA Bit 0 31 FIRSTPORTA Bit 1 30 FIRSTPO
Streszczenie treści zawartej na stronie nr. 19
Declaration of Conformity Manufacturer: Measurement Computing Corporation Address: 10 Commerce Way Suite 1008 Norton, MA 02766 USA Category: Electrical equipment for measurement, control and laboratory use. Measurement Computing Corporation declares under sole responsibility that the product CIO-DIO48H to which this declaration relates is in conformity with the relevant provisions of the following standards or other documents: EU EMC Directive 89/336/EEC: Electromagnetic Compat
Streszczenie treści zawartej na stronie nr. 20
Measurement Computing Corporation 10 Commerce Way Suite 1008 Norton, Massachusetts 02766 (508) 946-5100 Fax: (508) 946-9500 E-mail: info@mccdaq.com www.mccdaq.com
