Resumo do conteúdo contido na página número 1
I{IIGOM
PRIPORTVT2130
OPERATING INSTRUCTIONS
Ill
p’
RICOH COMPANY, LTD.
Resumo do conteúdo contido na página número 2
Note to users in the United States of America This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interfer
Resumo do conteúdo contido na página número 3
INTRODUCTION The Ricoh Priport VT2130 is a stencil duplicator which is carefully manufactured to exacting standards of high performance. This manual contains detailed instructions on the operation and care of the Priport VT21 30. To get the maximum versatility from this machine, all operators should read and follow the instructions in this manual. Please keep this manual in a handy place near the machine. 1. Wide range of reproduction ratios: 4 fixed reproduction ratios (100% plus 3 reduction ra
Resumo do conteúdo contido na página número 4
TABLE OF CONTENTS 12. Changing the Drum Unit for GUIDE TO COMPONENTS ............................ 27 Color Printing 1. Machine Exterior ........................ 2 13. Printing in Two Colors .............. 29 2. Machine Interior .......................... 4 3. Operation Panel .......................... 6 SPECIAL FUNCTIONS 1. Group Printing from the Same INSTALLATION REQUIREMENTS Original .................................... 30 1. Machine Environment ................. 8 2. Combine 2 Originals ....
Resumo do conteúdo contido na página número 5
GUIDE TO COMPONENTS 1. Machine Exterior 12 3 5 6 1’ / 1111 /7 A! 8 p– \ b 9 Q ‘%
Resumo do conteúdo contido na página número 6
1.Top Unit Open to remove the misfed original. 2. Original Guides Adjust these guides to position the originals correctly. 3.Original Table Place the originals on this table. 4. Original Table Release Use to open the original table unit to the left Lever for master installation. 5. Feed Roller Pressure Use to adjust the contact pressure of the Lever paper feed roller according to paper thickness. 6. Separation Roller Use to adjust the separation roller pressure to Pressure Lever prevent double f
Resumo do conteúdo contido na página número 7
2. Machine Interior 24 25 14 15 16 17 Ii= \ ’18 19‘ 4
Resumo do conteúdo contido na página número 8
14. Master Cut Button Press this button to cut the master paper lead- ing edge after installing a new master roll. 15. Pressure Release Lever Use to install the master roll, or to clean the thermal head. 16. Drum Rotation Button Press to replace the drum or to remove misfed paper. 17. Drum Unit The master paper is wrapped around this unit. 18. Ink Holder Set the ink cartridge in this holder. 19. Main Switch Use to turn the power on or off. 20. Small Size Paper Use to align the leading edge of sm
Resumo do conteúdo contido na página número 9
3. Operation Panel 4 2 3 1 m I t 1 1 Auto Cycle IO(I 93 75 64 (0000) OQ r (5 I A Cornblne 2 originals Lower Q%=% 17 16 18 1. Reset Key Press to reset error indicators. 2. Indicators Light or blink when a non-standard condition occurs within the machine. (See page 42.) Use to automatically process masters and 3. Auto Cycle Key make prints. Press to reduce the image. 4. Reduction Key 5. Image Position Press to shift the image forwards or back- wards on the print paper. Keys 6. Number Keys Press to
Resumo do conteúdo contido na página número 10
5 6 7 8 15 13 12 14 11 10 9 12. Stop Key Press to stop the machine operation. The machine will continue operation when the Print Start key or Master Making key is pressed. 13. Memory Key Use to select memory location number. (1 - 10) 14. Clear Key Press to change the number set in the counter. This key can be used only after the machine stops operation. 15. Speed Keys Press to adjust the rotation speed of the machine according to the type of image and printing paper. 16. Image Mode Key Press to
Resumo do conteúdo contido na página número 11
INSTALLATION REQUIREMENTS 1. Machine Environment The installation location should be carefully chosen because environmental conditions greatly affect the performance of a machine. - Optimum environmental conditions - I ml I 10 – 30°c ● Temperature: (50 - 86”F) 20 – 90% RH ● Humidity: ● Ventilation: Well-ventilated and wide room. ● On a strong and level base (a sturdy desk, etc.). ● The machine must be level within 5 mm (13/64”) both front to rear and le~ to right. - Environments to avoid - ● Dir
Resumo do conteúdo contido na página número 12
2. Access to Machine 10 cm {4.0”) Place the machine near a power source, providing Paper clearance as shown Paper I Del, very Feed 61 cm Table Table (24 O“) to the left. I + More than 70 cm (27 6“) ~ c than 60 cm” ~ (23 7“) (23 7’,1 3. Power Connection I f . Connect the power cord to a power source as follows. 120V, 50/60Hz more than 5.5 A . Make sure the plug is firmly in- serted in the outlet. ● Avoid multiwiring. . Do not pinch the power cord.
Resumo do conteúdo contido na página número 13
I DO’S AND DON’TS I - Operating Cautions - 1. While Printing : - Do not turn off the main switch. - Do not unplug the power cord. - Do not open the front cover. - Do not move the machine. 2. Keep corrosive liquids, such as acid, off the machine. Do not allow paper clips, staples, or other small objects to fall inside the 3. machine. 4. Always turn the machine off when you have finished printing for the day. 5. Do not touch print paper if your fingers are wet or oily; fingerprints may appear on p
Resumo do conteúdo contido na página número 14
ORIGINALS You can use the following type of originals. - Thickness - Max Min Max Min 7 E: Paper Feed :In Direction _ 42.1 glmz 132.5 g/rnz 0’ (11.1 lb) 1 -i (35.2 lb) Paper Feed J05 mm Direction --l (4 2“) u —307 ““— (120”) Cautions for original feeding. TO prevent an original misfeed or a machine malfunction, note the following cautions. . Remove paper clips or staples from the originals. . Correct curl or bend of originals before printing. . Make a copy and use the following types of copy as a
Resumo do conteúdo contido na página número 15
How to make an original when printing a part of a large original Large original After printing 1. Make sure the leading edge margin is 1! at least 15 mm (9/1 6“). Cut off excess paper .if necessary. +15mm Iii 2. Cut the upper edge of the original to make the center line A of the image centered. 3. Suitable original is completed. 12
Resumo do conteúdo contido na página número 16
I PRINTING PAPER I You can use the following types of paper as printing paper: - Thickness - Min Max Min 17 E Paper Feed E ~ Dlrect!on 215 g/mz 50 girl+ (57 lb) (13.3 lb) J“ u Y Paper Feed Dlrectlon r u of Avoid using the foliowing kinds . Roughly-cut paper . Paper of different thicknesses In the same stack . Buckled or curled paper . Short grained paper . Low stiffness paper Cautions for postcards printing ● As postcards do not absorb ink weii, offset images may appear on the rear side of sheet
Resumo do conteúdo contido na página número 17
OPERATION 1. Preparation for Printing 1. Open the paper carefully. 2. Adjust the paper feed plates to match the paper size. 3. Place the paper on the paper feed table. . Correct the paper curl before setting the paper. h b o x 4. Make sure that the paper feed side plates contact the paper lightly. 14
Resumo do conteúdo contido na página número 18
r I 5. Open the paper delivery table. . Set the paper delivery table for the paper size, using the size scale on the table. I I I 1 6. Lift the paper delivery side plates and adjust them to the paper size. 7. If you want to use paper smaller than 81/2” x 11”, lift the small size paper delivery end plate. . When you use 11” x 17“ and 81/2”x 14“ size paper, you do not need to lift the end plate. 8. Turn on the main switch. 15
Resumo do conteúdo contido na página número 19
2. Setting the Originals 1. Adjust the original guides to the size of the original. 2. Insert the original face down on the I 1 original table until it stops. . Only one original can be set at a time. 3. Select the image mode using the Image Mode keys. . Use the line mode when the original is printed matter. J . Use the photo mode when the original contains photos or colored images. The line mode is automatically selected ● when the main switch is turned on. 4. If reduced prints are desired, set
Resumo do conteúdo contido na página número 20
3. Printina 1. Enter the number of prints required using the Number keys. 1 . Up to 9999 prints can be entered at one If -4[ ■ 1 time. . To change the number entered, press the Clear key and then enter the new number. 2. Press the Master Making key. ● The original is fed, and the trial print is delivered to the paper delivery table. Check the image position. (See page 19 to 20.) 3. Press the Print Start key. . The number of prints set in the counter are made and the machine stops. . The same num
