Manual do usuário Metra Electronics 99-7952

Resumo do conteúdo contido na página número 1

INSTALLATION INSTRUCTIONS FOR PART 99-7952
APPLICATIONS
2005-2007 Suzuki Aerio
99-7952
KIT FEATURES
• DIN head unit provision
• ISO DIN head unit provision
KIT COMPONENTS
A) Radio Housing l B) ISO Brackets | C) Trim Plate
A B C
TOOLS REQUIRED:
Phillips Screwdriver I Small Flat Blade Screwdriver I Utility Knife
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION

Resumo do conteúdo contido na página número 2

99-7952 TABLE OF CONTENTS Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2, 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Resumo do conteúdo contido na página número 3

DASH DISASSEMBLY 99-7952 2005-2007 SUZUKI AERIO A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the trim panels from both sides of radio/climate controls. (Figure A) 3 Remove (4) Phillips screws holding radio to sub dash and remove radio. B (Figure B) Remove (4) )Phillips screws securing 4 the radio and brackets to the factory radio trim panel. (Figure C) 75 AUTO PUSH 65 PUSH 85 OFF AUTO A/C PUSH C Rear View 1

Resumo do conteúdo contido na página número 4

KIT ASSEMBLY 99-7952 DIN HEAD UNIT PROVISION Cut and remove the center bar in A 1 the DIN opening of the 99-7952 Radio Housing. Secure the 99-7952 radio housing to 2 the factory radio trim panel using the factory hardware. 3 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) B 4 Slide the aftermarket head unit into the cage and secure. (Figure B) 2

Resumo do conteúdo contido na página número 5

99-7952 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION A Cut and remove the center bar in 1 the DIN opening of the 99-7952 Radio Housing. 2 Secure the 99-7952 radio housing to the factory radio trim panel using the factory hardware. 3 Mount the ISO Brackets to the head B unit with the screws supplied with the unit. (Figure A) 4 Slide the head unit into the radio opening until the side clips engage. (Figure B) Snap the Trim plate into the Radio 5 Housing. (Figure B) 3

Resumo do conteúdo contido na página número 6

KIT ASSEMBLY 99-7952 FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. 2 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring co

Resumo do conteúdo contido na página número 7

99-7952 NOTES 5

Resumo do conteúdo contido na página número 8

INST997952 1-800-221-0932 www.metraonline.com © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION REV. 04/10/07 INST99-7952