Resumo do conteúdo contido na página número 1
2-STAGE PERFORMER RPM NITROUS SYSTEM
Catalog #70003 & #70004
Table of Contents
Page #
a. Edelbrock General Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
b. Before You Install Your Edelbrock Nitrous System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
c. What is Nitrous Oxide? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resumo do conteúdo contido na página número 2
2-Stage Performer RPM Nitrous System Catalog #70003 & #70004 Thank You…. …for purchasing an Edelbrock Nitrous Oxide Injection System. Nitrous Oxide injection is one of the most exciting performance enhancements, for the dollar invested, on the market today. With the use of nitrous oxide come some important safety considerations. This manual has been written to help you during the installation and use of your Edelbrock Nitrous System. Please read it completely before you install and use your syst
Resumo do conteúdo contido na página número 3
Caution!! Before You Install Your Edelbrock Nitrous System… Please read this Installation manual fully before installing this system. You will need to have available the following tools: Hand Tools: ❑ Socket set including ratchets and extensions ❑ Screwdrivers ❑ Pliers ❑ Bench vise ❑ Wire crimping pliers, wire strippers ❑ Floor jack ❑ Measuring tape and placement markers ❑ Vehicle jackstands ❑ Safety glasses ❑ Timing light Power Tools: ❑ Power drill ❑ Drill bits You should understand the followi
Resumo do conteúdo contido na página número 4
WHAT IS NITROUS OXIDE? Nitrous Oxide is a cryogenic gas composed of nitrogen and oxygen molecules. It is stored as a “gas over a liquid” which means that both liquid and gaseous nitrous oxide is delivered into your engine. It is 36% oxygen by weight, which is what produces the added horsepower. By injecting more oxygen (and a corresponding fuel signal), we create the additional power much like a supercharger or a turbocharger does. Nitrous Oxide is considered an “oxidizer” and not a fuel. Nitrou
Resumo do conteúdo contido na página número 5
1.0 Introduction to your Edelbrock 2-Stage Performer RPM Nitrous System Within the pages of this manual is information, safety tips and operation instructions for your new Edelbrock Nitrous System. Watch for these symbols to know where to go for information. ….There is safety related information here. ….shows where technical information about your vehicle or specific skills that may help during installation. ….call Edelbrock Technical support hotline for more information. ℡ ℡ 1.1 General I
Resumo do conteúdo contido na página número 6
1.2 Jet Map Information Edlebrock engineering has conducted dyno testing with the 2-Stage Performer RPM System to provide jetting maps for the two separate plates at different jetting levels. These jet combinations are supplied with this system to enable you to vary your engine’s power output. On a typical mildly-modified 350 cubic inch engine, you can expect the following approximate power gains for each of the jetting levels: The dyno tests were conducted at Edelbrock using a mildly-modified 3
Resumo do conteúdo contido na página número 7
1.3 Engine Operation Considerations When used correctly, nitrous oxide safely elevates cylinder pressures and temperatures while increasing combustion rate. These characteristics make the engine more sensitive to detonation. To ensure proper performance and engine life, the following tips are suggested: Adequate Fuel Pressure and Delivery: When designing your fuel system, plan on your pumps and lines flowing at least 0.1 gallons per hour per horsepower at rated pressure. The testing at Edelbrock
Resumo do conteúdo contido na página número 8
1.4 2-Stage Performer RPM Nitrous System Bill of Materials Qty. Description Qty. Description Plate and Hardware Bottle Hardware 1 ea. 2-Stage Performer RPM Nitrous Plate 1 ea. 660 4AN Bottle Nut 2 ea. Plate Gaskets 1 ea. Teflon Washer 4 ea. Carburetor Studs Electrical System Components Solenoids and Solenoid Hardware 1 ea Micro Switch Bracket 1 ea. Performer Nitrous Solenoid 1 ea. Electrical Component Packages 1 ea Performer Fuel Solenoid (see “3.0 Electrical System Installation” 1 ea
Resumo do conteúdo contido na página número 9
2.0 Nitrous System Installation 2.1 Nitrous Bottle Installation The nitrous oxide storage cylinder is typically called a “nitrous bottle”. It is an aluminum cylinder, designed and manufactured to withstand very high pressures. The valve on top of the bottle is a high-flow design that allows easy opening and closing which controls the nitrous flow to the engine compartment. Accurate calibration of your nitrous system depends on the bottle remaining at a stable temperature. In vehicles (such as Co
Resumo do conteúdo contido na página número 10
2.2 Bottle Orientation Accurate calibration of your nitrous system depends on the bottle remaining at a stable temperature. Choosing the proper location and orientation for your bottle can greatly affect the overall operation of the nitrous system. Please read the entire bottle mounting instruction section before making your final bottle location decisions. Bottle placement is critical to the performance of your nitrous system. It is important to understand how the bottle valve and siphon tube a
Resumo do conteúdo contido na página número 11
2.3 Nitrous Bottle Installation After you have determined the location and orientation of the nitrous bottle, use the following procedure to install the bottle: 2.3.1 Street Car Installations 1. Disconnect vehicle’s battery. 2. Determine the location of the bottle within the confines of the rear of the vehicle. 3. Once a mounting location has been determined, raise the vehicle (following all safety practices involved in working on a vehicle from under the vehicle) and verify that there are no fu
Resumo do conteúdo contido na página número 12
2.4 Nitrous Feed Line Mounting 1. Determine the route your main nitrous feed line will follow. Ensure the path does not route the nitrous feed line too close to the exhaust system, suspension, electrical lines/components or tires. 2. Attach nitrous supply line to bottle. 3. Feed nitrous line along proposed route. 4. Secure nitrous supply line to underside of vehicle. Note: Stainless steel covering of the main nitrous feed line is very abrasive. Shield painted components or sensitive system comp
Resumo do conteúdo contido na página número 13
2.5.2 Performer Solenoid Assembly 1. Hold the Performer Nitrous Solenoid securely (such as in a bench vise) being careful not to harm the solenoid or block the inlet or outlet of the solenoid. 2. Install the nitrous filter fitting (Blue filtered fitting 4AN x 1/8NPT) using liquid Teflon paste in the inlet port of the Performer Solenoid. Be careful not to over tighten the fitting causing it to strip or gaul. 3. Install the 3AN x 1/8NPT (Blue straight fitting) using liquid Teflon aste in the outle
Resumo do conteúdo contido na página número 14
2.6 Mounting Your Solenoids (Continuation)... Remember that there are many factors to take into account when mounting your solenoids. Make sure that you mount the solenoids within line length of the plate. Other factors or components that could potentially interfere with solenoid placement are: - Water neck/thermostat housings - Water fittings - Distributor housing - Vacuum advance canisters - Air filter housings - Throttle linkage passageways - Valve covers and valve cover fasteners Pictured be
Resumo do conteúdo contido na página número 15
2.8 Nitrous Injection Plate Installation The Edelbrock Nitrous System injection plate is a precision-designed CNC-machined component. It has been designed to safely introduce a precise, metered nitrous and fuel signal to promote proper mixing and distribution into the intake manifold. The jet map supplied in this manual will give you the proper jet sizes to use for each of the power levels available for this plate. The jet fittings are color-coded for use with nitrous (blue) and fuel (red). The
Resumo do conteúdo contido na página número 16
3.0 Electrical System Installation 3.1 Nitrous Electrical Components Bill of Materials (BOM) Item # Quantity Description 1 1 ea. Activation microswitch 2 1 ea. Activation microswitch bracket (not shown) 3 2 ea. Activation microswitch mounting nut 4 2 ea. Activation microswitch mounting screw 5 1 ea. 2 Stage 30 amp relay 6 1 ea. Wire harness with integral relay/fuse holders 7 1 ea. Red lighted toggle switch 8 6 ea. 18/22g female spade connector, Nylon insulated 9 2 ea. 14/16g female spade connec
Resumo do conteúdo contido na página número 17
3.2 Nitrous Electrical System Wiring Diagram Page 17 of 28 Rev. 03/04 ©2004 Edelbrock Corporation Brochure No. 63-0190 - DC/mc
Resumo do conteúdo contido na página número 18
3.3 Nitrous Electrical System Installation Procedures Determine the location of the relay and fuse holder wire harness. Most common installations locate these components inside the driver’s compartment and close to the fuse panel under the dash. You can also mount the relay and ruse holder harness close to the battery. However, these connectors are water-resistant not waterproof, so care is required when mounting this assembly under the hood of your vehicle. Wire Schematic Origin and Destination
Resumo do conteúdo contido na página número 19
3.5 Arming Switch and Installation The arming switch is a red, lighted switch that is a “MASTER” arming switch for your nitrous system. Without it, your nitrous system would be “on” all of the time and capable of engaging anytime you go to wide-open throttle conditions with your vehicle. The switch, when in the “armed” position, is well lit. Therefore, it should be placed in an obvious position well within the line of sight and easy reach of the driver. Please refer to the procedures below for t
Resumo do conteúdo contido na página número 20
3.6 Microswitch Installation and Wiring (continuation)... The bolts used to attach the microswitch have extra length to allow for spacing the microswitch away from the bracket to offer a level of adjustability of the microswitch. After determining the position of the microswitch, we recommend trimming the bolts for a clean installation. Due to the wide variety of throttle linkage combinations in use, it is impossible to supply a microswitch bracket custom tailored to each application. The univer
