Resumo do conteúdo contido na página número 1
Subwoofer
VMS-8
USER’S
MANUAL
Small, High-Performance Subwoofer
Resumo do conteúdo contido na página número 2
. www.v elodyne.com VMS User’s Manual i
Resumo do conteúdo contido na página número 3
Table of Contents Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Prepare for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Line-Level Connection - Option A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 L
Resumo do conteúdo contido na página número 4
Congratulations! Congratulations on your purchase of a Velodyne VMS subwoofer system. This system represents the state-of-the-art in home audio reproduction and will provide you with years of listening pleasure when properly cared for. Read and follow this instruction manual to insure safe and proper system connection and operation. Caution! Please observe the following instructions to insure safe and proper system operation. Note: Do not leave unit in direct sunlight or use in high humidity en
Resumo do conteúdo contido na página número 5
Prepare for Installation Your new Velodyne subwoofer provides for a number of installation options. Read all the installation information below in order to determine which installation option is best for your system. Remember to perform all installation procedures with system power turned off to prevent possible damage. Placement The first step in installing your new VMS is to determine where it will be placed in the room. Unpack the system carefully and use the following guidelines in order
Resumo do conteúdo contido na página número 6
Installation Your new subwoofer is equipped with speaker-level and line-level inputs. Use the LINE LEVEL jacks when connecting your subwoofer to a pre-amp, signal processor, line-level crossover or receiver with pre-amp level outputs. The SPEAKER LEVEL jacks connect directly to the speaker outputs of any amplifier, integrated amplifier or receiver. Your amplifier section will notice no additional loading effects when you use these inputs due to their very high impedance. Important!!! Do not use
Resumo do conteúdo contido na página número 7
Crossover Switch - INTERNAL X-OVER/SUBWOOFER DIRECT This switch allows the internal crossover circuitry to be removed from the signal path. This is r equired in certain installations which route the signal through external processors with a crossover circuit of their own, such as the new digital units. Simply move the switch to SUBWOOFER DIRECT to disengage the built-in crossover. For all other installations which do not have a separate electronic crossover, we recommend you leave the switch se
Resumo do conteúdo contido na página número 8
Figure 1. Installation Using LFE Line-Level Inputs Note: If not using an external crossover, you should use the built-in crossover for optimal performance. When using a single channel input (such as a surround sound processor’s subwoofer out or LFE), the auto on/off circuit sensitivity will be affected. When one input channel is used instead of two, the unit will see lower signal levels present at the inputs. This may cause the unit to turn off when listening at low volume levels. If this occur
Resumo do conteúdo contido na página número 9
Line-Level Connection - Option B Figure 2 shows connection from a pre-amplifier’s main outputs to the left and right inputs of your Velodyne subwoofer. You will also need to connect a second pair of RCA cables from the outputs on the back of your subwoofer to the inputs on the back of your amplifier. When the subwoofer is installed in this fashion, your satellite speakers will be crossed over at 80 Hz which removes the lower bass frequencies from your external amplifier and speakers, enabling th
Resumo do conteúdo contido na página número 10
Speaker-Level Connections Figure 3 shows an easy way to connect your Velodyne subwoofer directly to your receiver or integrated amplifier, if it lacks line-level outputs. You may also connect your satellites directly to your receiver or amplifier along with the subwoofer. Your receiver or amplifier will not notice the additional load of the subwoofer due to the high input impedance. Figure 3. Installation Using Speaker-Level Inputs Caution!!! To avoid damage to your main amplifier, be sure to
Resumo do conteúdo contido na página número 11
Subwoofer Outputs The Velodyne subwoofer is designed to operate using the full range audio signal for input when ® ® using the built-in crossover. Many home theater processors/receivers (Dolby Digital , DTS , THX™) have a “subwoofer out” jack that is internally filtered and designed to be used with a powered subwoofer. In these installations, you may bypass the internal crossover in either the processor or the Velodyne subwoofer. In some installations, it may be beneficial to have a steeper ulti
Resumo do conteúdo contido na página número 12
Care of Your Subwoofer Your Velodyne subwoofer does not require any regular maintenance. Normal dusting or cleaning of the surface for appearance purposes is all that is required. We suggest you avoid any harsh detergents or chemicals when cleaning the cabinet. Abrasives, detergents, or cleaning solutions may damage the finish on the cabinet. We recommend using only a damp cloth to clean the cabinet. During normal conditions, your new subwoofer may be left on continuously without any problems.
Resumo do conteúdo contido na página número 13
Specifications Specifications VMS-8 Woofer 8” forward firing (6.5” piston diameter) Amplifier 2000 watts Dynamic (Class D) 1000 watts RMS Power High Pass Crossover 80 Hz (6 dB/octave) Low Pass Crossover 40 Hz-120 Hz 12 dB octave initial, 48 dB octave ultimate Frequency Response 26-120 Hz (+/-3 dB) Harmonic Distortion <5% (typical) Magnet Structure 204 oz. (12.7 lbs) Voice Coil 2.5” Dual Layer inner/outer wind Inputs Gold plated line-level and speaker-level Outputs Line-level, 80 Hz up Phase
Resumo do conteúdo contido na página número 14
Velodyne Products 115 -120V 220 - 240V ® ® DD Series Optimum Series DD Series SPLi Series DD-10 Optimum-8 DD-10 SPL-800i DD-12 Optimum-10 DD-12 SPL-1000i DD-15 Optimum-12 DD-15 DD-18 DD-18 SPL-Ultra Series Digital Drive 1812 Digital Drive 1812 SMS™-1 SPL-800 Ultra Signature Edition Signature Edition SPL-1000 Ultra SubContractor™ SPL-1200 Ultra DEQ-R Series Series CHT-Q Series DEQ-8R SC-1250 CHT-8Q SubContractor™ DEQ-10R SC-10 CHT-10Q Series DEQ-12R SC-12 CHT-12Q SC-1250 DEQ-15R SC-15 CHT-15Q SC-
Resumo do conteúdo contido na página número 15
FOR YOUR RECORDS. . . Date Purchased_________________________________________________________________ Dealer_________________________________________________________________________ Serial #________________________________________________________________________ *NOTE: Please complete and return your warranty card within ten (10) days or Register. . . ON LINE . . . It’s faster . . . and easier www.velodyne.com LIMITED WARRANTY - U.S. AND CANADA ONLY VELODYNE ACOUSTICS, Inc. (“VELODYNE”) warr
Resumo do conteúdo contido na página número 16
Velodyne Acoustics, Inc. 345 Digital Drive Morgan Hill, CA 95037 408.465.2800 voice 408.779.9227 fax 408.779.9208 service fax .velodyne.com www -mail: service@velodyne.com Service E Product E-mail: help@velodyne.com Technical E-mail: techhelp@velodyne.com 63-VMS Rev A MAY09 . www.v elodyne.com VMS User’s Manual 13
