Resumo do conteúdo contido na página número 1
INSTALLATION INSTRUCTIONS
Instrucciones de instalación Istruzioni di installazione
Installationsanleitung Installatie-instructies
Instruções de Instalação Instructions d´installation
Automated Display Lift
This device complies with part 15 of the FCC rules. Operation is subject to the following 2 conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has b
Resumo do conteúdo contido na página número 2
CM2 Installation Instructions CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. CSAV
Resumo do conteúdo contido na página número 3
Installation Instructions CM2 CONTENTS INSTALLATION REQUIREMENTS ..............................................................................................................5 Power Requirements and Wiring ...............................................................................................................5 INSTALLATION ............................................................................................................................................5 Pre-Installation Configur
Resumo do conteúdo contido na página número 4
CM2 Installation Instructions LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging losdraaien Gat
Resumo do conteúdo contido na página número 5
Installation Instructions CM2 2. Measure the distance from the center of a bottom mounting INSTALLATION REQUIREMENTS button to the lowest point of the display. The CM2 has been designed to be mounted into a cabinet or 3. Record measurement. similar type of furnishing. WARNING: IMPROPER INSTALLATION CAN LEAD TO LIFT TIPPING CAUSING SEVERE PERSONAL INJURY OR 1 DAMAGE TO EQUIPMENT! It is the installers responsibility to make certain the structure to which the lift is being mounted is capable of sup
Resumo do conteúdo contido na página número 6
CM2 Installation Instructions 9. Secure faceplate to faceplate mounting bracket using two locknuts. (See figure 6) 6 6 10 10 9 x2 Figure 5 10. Using the remote control, lower the lift until it stops. 5 4 (See figure 3) If more than 2" of faceplate adjustment is required: 11. Raise lift following instructions in step 6. (See figure 3) 12. Loosen four nuts securing faceplate mounting bracket to frame. (See figure 6) Figure 3 13. Slide faceplate mounting bracket upward desired amount. (See figure 6
Resumo do conteúdo contido na página número 7
Installation Instructions CM2 15. Align studs in faceplate with appropriate holes in faceplate mounting bracket and hang faceplate on bracket with studs. WARNING: IMPROPER INSTALLATION CAN LEAD TO 16. Secure faceplate to faceplate mounting bracket using two MOUNT FALLING CAUSING SEVERE PERSONAL INJURY locknuts. (See figure 7) OR DAMAGE TO EQUIPMENT. Displays can weigh in excess of 40 lbs (18.1kg). ALWAYS use two people and proper lifting techniques when installing display. WARNING: IMPROPER INST
Resumo do conteúdo contido na página número 8
CM2 Installation Instructions NOTE: Verify that there is at least 1" of clearance between bottom of display and mount base. 3. If there is less than 1" of clearance, remove the display and refer to Adjusting Faceplate Location section, and adjust display height accordingly. NOTE: Holes are provided in the faceplate for use with a padlock or similar locking device, if desired. In addition, the pin and nut may be removed from the upper holes and moved to the lower holes for use as a more Top of D
Resumo do conteúdo contido na página número 9
Installation Instructions CM2 NOTE: With the mount configured for the display and the display installed, it is now possible to calculate the Cover minimum I.D of the cabinet. Determining Minimum I.D. of Furniture 1. Measure and record distance "A" in figure below. (See figure 16) 2. Measure and record distance "B" from figure below. This is the material thickness of the cover that will be mounted to the CM2. (See figure 16) 3. Add measurements from step one and two together. The total is the min
Resumo do conteúdo contido na página número 10
CM2 Installation Instructions Cable Installation and Routing Cable Guide The CM2 has an integrated cable management system that Side Cover allows cables to be automatically "fed out" as the lift raises, and "reeled in" as the lift lowers while maintaining constant cable tension. IMPORTANT ! : The CM2 requires minimum cable lengths of 8 feet from display through lower mount. To install cables: 1. Remove two screws securing cable guide side cover. 2. Set screws aside for reuse. (See figure 17) 3 1
Resumo do conteúdo contido na página número 11
Installation Instructions CM2 4 From Display x1 5 5 6 8 4 x3 8 4 x2 7 7 9 9 10 10 Figure 19 11
Resumo do conteúdo contido na página número 12
CM2 Installation Instructions 6. Route cable(s) down through opening at rear of middle 13. Slide cable guide side cover over cable guide making cable clamp mounting bracket. (See figure 19) and certain lip on back cover plate is fully seated in groove in (See figure 20) cable guide side cover. (See figure 21) NOTE: If plug on cable will not fit through opening loosen or remove one screw securing middle cable clamp Back Cover Plate mounting bracket to mount frame and pivot middle cable clamp moun
Resumo do conteúdo contido na página número 13
Installation Instructions CM2 7. Mark eight base mounting hole locations. (See figure 24) Mount Installation 8. Drill pilot holes at marked locations. The CM2 has been designed to be mounted into a cabinet or 9. Mark four side bracket mounting hole locations. similar type of furnishing. (See figure 41) The following installation instructions assume a suitable 10. Drill four pilot holes at marked locations. structure and surface exists prior to installation. 11. Secure mount base to mounting surf
Resumo do conteúdo contido na página número 14
CM2 Installation Instructions ADJUSTMENTS Display Travel Adjustment The CM2 is designed to allow the adjustment of both "Extend" and "Retract" display travel limits. The CM2 is shipped set at maximum extension and retraction. There is an upward travel limit adjustment screw and a downward travel limit adjustment screw located on the top right hand side of the mount. (See figure 25) NOTE: 10 full turns of the "Extend" or "Retract" travel adjustment screws is equal to 1" of display travel. 1. Tur
Resumo do conteúdo contido na página número 15
Installation Instructions CM2 Lift Column Bearing Adjustment The upper and lower lift columns are aligned using two lift bearings, one upper and one lower. Bearing adjustment is pre-set at the factory, however, there may be times when it is required to make slight adjustments in Upper Lift Column bearing tightness to eliminate excess play in lift columns or Bearing Adjustment Points noise. WARNING: OVERTENSIONING CAN LEAD TO DAMAGE TO EQUIPMENT! DO NOT overadjust! IMPORTANT ! : Display should be
Resumo do conteúdo contido na página número 16
CM2 Installation Instructions Normal Operating Mode Extended Programming Capabilities The CM2 allows for extended programming to make the mount KEY FUNCTION REQUIRED ACTION compatible with other devices such as a Universal Remote or 1 MOVE DISPLAY TO HOME PRESS ONCE other control devices through a serial connection. 2 EXTEND DISPLAY PRESS AND HOLD Setting or changing the configuration of the CM2 is done 3 NOT USED N/A through the remote control provided with the mount. 4 NOT USED N/A The remote
Resumo do conteúdo contido na página número 17
Installation Instructions CM2 NEC Protocol: Table 1-1: IR System Code The modulated carrier is usually derived from 455kHz and is 1/12 of the frequency with 1/3 duty cycle. Switch # 2 Switch # 1 Switch # 3 Custom Code When data are transmitted repeatedly, the frame cycle is 107.9ms or 186 period. Off Off Off 6E A frame consists of a syn pulse, an eight-bit custom code, an On Off Off E1 eight-bit inverted custom code, an eight-bit data code and an Off E2 Off On eight-bit inverted data code. On O
Resumo do conteúdo contido na página número 18
CM2 Installation Instructions IR-SE15 Programming IR-SE15 Control Features: Carrier Frequency:38KHz Protocol:NEC - Full Repeat System Code(s):6E (Default) - Multiple Codes Selected via Key-Press (see below) Table 1-2: IR-SE15 Control Codes Key Number Key Name Hex Code 1 HOME 02 2 SAVE 1A 3 UP 07 4 LEFT 09 5 STOP 0A 6 RIGHT 0B 7 DOWN 0D 8 PRESET 1 12 10 PRESET 2 13 12 PRESET 3 14 To Change System Code: 1. Press and Release Key 3 + 7 (Enter Setup Mode) 2. Press and Release Key 8 3. Press an
Resumo do conteúdo contido na página número 19
Installation Instructions CM2 IR-SC33a Programming IR-SC33a Control Features Carrier Frequency: 38KHz Protocol: NEC - Full Repeat System Code: 6E Table 1-4: Key Number Key Name Hex Code 3 HOME 02 8 RETRACT 07 10 LEFT 09 12 RIGHT 0B 14 EXTEND 0D 19 PRESET 1 12 20 PRESET 2 13 21 PRESET 3 14 27 SAVE 1A 3 8 12 10 14 20 19 21 27 19
Resumo do conteúdo contido na página número 20
CM2 Installation Instructions Serial Communications NOTE: Check with the appropriate automation system vendor for available drivers and/or software for any external devices. Notes: [PR] = Product ID (CM2 = 02) [AD] = Address (see address description & table) [CR] = ASCII Carriage Return [CH] = Check Code [ST] = Status (see status table) Connecctions to be made to 9 pin connector as follows: RS-485 REF Pin 7 RS-485 + Pin 8 RS-485 - Pin 9 Communication parameters as specified in ANSI TIA/EIA-485-A
