Resumo do conteúdo contido na página número 1
45613
Wireless Lighting Control
3-way
Dimmer
Switch Kit
™
GE SmartHome
®
Z-Wave Certified
Wireless Lighting Control
Resumo do conteúdo contido na página número 2
Introduction: ® Thank you for your purchase of a GE Z-Wave enabled control device. Z-Wave technology is designed to automate lighting/ home control and provide easy remote operation of all your Z-wave enabled devices. The GE Z-Wave product family includes a variety of devices to control lighting in your home. Control one room or your entire house, and you can do it all now or start with one room and add more over time. The 3-way dimmer switch kit is one ® components of a Z-Wave control
Resumo do conteúdo contido na página número 3
The auxiliary switch is not Z-Wave enabled and does not directly control electrical loads. It must be used with a compatible Z-Wave enabled, 3-wire switch in three-way installations where a light is controlled from 2 locations such as the top and bottom of a staircase. This switch communicates with the Z-Wave enabled switch, providing manual On/Off/Dim control of the connected lighting (through the Z-Wave enabled switch) and synchronization of the lighting status (On/Off/Dim level) bet
Resumo do conteúdo contido na página número 4
WARNING RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS Controlling Appliances: Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be in a different room than the controlled appliance, also an unintentional activation may occur if the wrong button on the remote is pressed. Z-Wave devices may automatically be powered on due to timed event programming. Depending upon the appliance, these unattended or unintentional operations co
Resumo do conteúdo contido na página número 5
Wireless Range This device complies with the Z-Wave standard of open- air, line of sight transmission distances of 65 feet. Actual performance in a home depends on the number of walls between the remote controller and the destination device, the type of construction and the number of Z-Wave enabled devices installed in the control network. GE Z-Wave network Every Z-Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps
Resumo do conteúdo contido na página número 6
Effects of Home Construction on Wireless Range Between Z-Wave Enabled Devices. Note: The distances shown in the table below are typical examples. Actual performance in your home will vary. From the Remote (or repeating Z-Wave module) to destination device: Type of Construction Wood Frame Brick, Tile or w/Drywall Concrete Plastic Metal Plastic Metal J-Boxes* J-Boxes J-Boxes* J-Boxes ** 0 100’ 80’ 100’ 80’ Number 1 70’ 56’ 60’ 48’ of Walls or Obstacles 2 49’ 39’ 36’ 29’ 3 34’ 27’ 21’ 17’ *
Resumo do conteúdo contido na página número 7
Please Note: Z-Wave home control networks are designed to work properly alongside 802.11 wireless computer networks, Bluetooth® and other 2.4GHz or 5.8GHz devices. Some baby cams, wireless video devices and older cordless phones using the 900MHz frequency range may cause interference and limit Z-Wave functionality. Many 900MHz products have a switch to select channel “A” or “B”. You may find that one of these channels will cause less interference than the other. IMPORTANT NOTE ABOUT 3
Resumo do conteúdo contido na página número 8
Typical 3-way circuit Black Black Black Colored(NOT GREEN) Switch 1 Switch 2 White Correct switch position Z-Wave Z-Wave Primary Auxiliary Incorrect switch position Z-Wave Z-Wave Primary Auxiliary Refer to the wiring diagram for wiring details
Resumo do conteúdo contido na página número 9
IMPORTANT NOTE ABOUT 3-WAY CIRCUITS CONT. The yellow wire from the 45607 must only be connected to the yellow wire of the 45610 via the traveler wire. The dimmer switch will fail if the yellow wire is connected to Line (Hot), Neutral or Ground. It must be insulated properly if it is not used. Please consult an electrician if you have trouble identifying the type of wiring circuit you wish to convert or if you do not feel confident in your ability to convert the circuit to Z-Wave control.
Resumo do conteúdo contido na página número 10
Wiring Digram Hot (Black) Black Black Yellow Yellow Blue Auxiliary Dimmer Switch Switch One Auxiliary White Switch for 500W 3-way installation. Ground Green Green (Green) Neutral (White) Hot (Black) Black Yellow 45610 Auxiliary Two Auxiliary Switch Switches for 4-way installation. Green Up to 2 Auxiliary switches may be used to create a 4-way installation
Resumo do conteúdo contido na página número 11
Single, Dual and Triple Gang Boxes The metal plate surrounding the switch assembly is a heat sink. The maximum load rating (500W) is provided when installed in a Hot (Black) single gang box with the full heat sink. Multiple 45607 Dimmer Switches may be installed in dual or triple gang boxes and, if Black Black Yellow Yellow Blue necessary, one or both sides of the heat sink may be removed by bending it at the score lines. There is a corresponding reduction in the switch’s load rating
Resumo do conteúdo contido na página número 12
Traveler White (Colored not green) (Neutral) Yellow (Traveler) Blue (Load) Black Black (HOT or Load) (HOT or Load) Green (Ground) 45607
Resumo do conteúdo contido na página número 13
Traveler (color not green) Green (grounded) Yellow (traveler) Black (Hot) Red/White (Hot) 45610
Resumo do conteúdo contido na página número 14
WARNING SHOCK HAZARD! Turn OFF the power to the branch circuit at the circuit breaker in your electrical service panel. Ensure power is OFF before you install this device. All wiring connections must be made with the POWER OFF to avoid personal injury and/or damage to the switch. 1. Shut off power to the circuit at fuse box or circuit breaker. 2. Remove wall plate. !Warning: Verify power is OFF to switch before continuing. 3. Remove the switch mounting screws. 4. Carefully remove the s
Resumo do conteúdo contido na página número 15
Instructions: 1. Strip insulation 3/8” for 12 or 14 AWG wire. Strip insulation 7/16” for 16 or 18 AWG wire. 2. Hold stripped ends together in parallel and align any frayed strands (do not twist wires). 3. Push wires firmly into connector. Twist connector clockwise with fingers until tight. Pull wires to check for tightness. Wire Connector / Combination Chart One #14 w/one-to-four #16 or #18 One #12 w/one-to-three #14 or #16 or #18 Two #14 w/one-to-three #16 or #18 Two #12 w/one
Resumo do conteúdo contido na página número 16
Key Features - Controls one light from two locations - Remote On/Off/Brightness control via the Z-Wave controller/ network - Manual On/Off/Brightness control with the front panel rocker - LED indicates primary switch location in a dark room - Adjustable Dim rates BASIC OPERATION Remote Control GE Z-Wave remotes provide control of an Individual device, Groups of devices and Scenes. Other brands of Z-Wave Certified remotes may not offer as much flexibility in how you can set up your lighting c
Resumo do conteúdo contido na página número 17
must still tap (press & release) the bottom of the rocker to turn the power OFF. - When OFF, pressing and holding the bottom of the rocker will cause the lighting to go to the minimum dim level. Program your light Switch (The model 45607 primary switch must be used to include or exclude the dimmer switch from the Z-Wave home control network.) - Refer to the instructions for your primary controller to access the network setup function and include or exclude devices. - When prompted by your
Resumo do conteúdo contido na página número 18
ADVANCED OPERATION The following Advanced Operation parameters require that you have an advanced controller like the 45601 Advanced remote. Advanced remotes from other manufacturers may also be able to change these settings; however, basic remotes do not have this capability. All On/All Off Depending upon your primary controller, the 45607 dimmer switch can be set to respond to ALL ON and ALL OFF commands in up to four different ways. Some controllers may not be able to change the resp
Resumo do conteúdo contido na página número 19
- Parameter No: 3 - Length: 1 Byte - Valid Values = 0 or 1 (default 0) Invert Switch If the dimmer switch is accidentally installed upside down with “On” at the bottom and “Off” at the top, the default On/Off rocker settings can be reversed by changing parameter 4’s value to “1”. - Parameter No: 4 - Length: 1 Byte - Valid Values = 0 or 1 (default 0) Dim Rate Adjustments Both the number of steps (or levels) that the dimmer will change and the timing of the steps can be modified to suit person
Resumo do conteúdo contido na página número 20
- Valid Values: Parameter 7 (default = 1) Valid Values: 1-99 Parameter 8 (default = 3) Valid Values: 1-255 2. Manual Control Dimming (pressing the Dimmer’s rocker) - Parameter 9 (number of steps or levels) - Parameter 10 (timing of the steps) - Length: 1 Byte - Valid Values: Parameter 9 (default = 1) Valid Values: 1-99 Parameter 10 (default = 3) Valid Values: 1-255 3. When Receiving an All-On or All-Off Command - Parameter 11 (number of steps or levels) - Parameter 12 (timing of the steps) - Len
