Resumo do conteúdo contido na página número 1
NEC Display Solutions of America, Inc.
Installation and Assembly Manual:
Custom Ceiling Mount for NEC NP400, NP500, NP500W,
and NP600 Projectors
Model: NP600CM
Maximum Load Capacity: 50 lb (22.7 kg)
Features:
TM
• ImageLock alignment prevents picture sag or drift
Wrench access slot for easier flush mount installations
Exclusive aluminum track quick release
ISSUED: 08-05-08 SHEET #: 056-9008-1
1 of 10
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112
Resumo do conteúdo contido na página número 2
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING Do not begin to install your Peerless product until you have read and understood the instructions and warnings con- tained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call Peerless customer care at 1-800-729-0307. This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully
Resumo do conteúdo contido na página número 3
Before you start check the parts list to insure all of the parts shown are included. Parts List A Description Qty. Part # A projector mount assembly 1 055-2803 B 560-9646 4 mm security allen wrench 1 C #10-32 x 3/8" serrated washer head socket pin screw 2 520-2151 D #10-32 x 1/4" socket pin screw 1 520-2196 C D E flat washer 2 540-1078 F #14 x 2.5 phillips hex head wood screw 2 5S1-015-C04 G concrete anchor 2 590-0097 AA adapter plate 1 055-2869 E G BB M4 x 16 mm serrated socket pin screw 3 510-
Resumo do conteúdo contido na página número 4
Installation to Extension Column / Ceiling Plate NOTE: Refer to accompanying instructions with ceiling plates (sold separately) for installing these models to 2 ceiling. Screw projector mount assembly (A) onto extension column as shown in figure 2.1. NOTE: For 3/4" extension columns, reducer ACC 913 (not included) will be required as shown in figure 2.2. Tighten swivel stop screw against extension column, flush mount tube or reducer using 4 mm security allen wrench (B) as shown in figure 2.3. NO
Resumo do conteúdo contido na página número 5
Installation To Wood Joist Ceilings WARNING Tighten wood screws so that projector mount assembly is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. Never tighten in excess of 80 in lb (9 N.M.). Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is highly recommended. Place projector mount assembly (A) on ceiling as a template and mark the center of the two
Resumo do conteúdo contido na página número 6
Installation to Concrete Ceilings WARNING Tighten wood screws firmly, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. Never tighten in excess of 80 in lb (9 N.M.). Place projector mount assembly (A) on ceiling as a concrete 1 2 template and mark the center of the two mounting ceiling holes. Drill two 1/4" (6 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach projector mount assembly (A) using two concrete anchors (G), two flat wash
Resumo do conteúdo contido na página número 7
Installation to Threaded Rod Thread two 1/4-20 hex thin nylon-insert locknuts (not included) on two 1/4-20 threaded rods (not included) to the 2 desired height of projector mount assembly. Attach projector mount assembly (A) to the two 1/4-20 threaded rods using two 1/4-20 hex thin nylon-insert locknuts as shown in figure 2.7 or figure 2.8. 1/4-20 THREADED ROD (NOT INCLUDED) 1/4-20 THREADED ROD (NOT INCLUDED) 1/4-20 HEX THIN 1/4-20 HEX THIN NYLON-INSERT NYLON-INSERT LOCKNUT LOCKNUT (NOT INCLUDE
Resumo do conteúdo contido na página número 8
Attaching Adapter Plate to Projector Align shoulder on connection block opposite notch 3 in adapter plate (AA). Attach adapter plate to CONNECTION BLOCK connection block from projector mount assembly (A) using two #10-32 x 3/8" serrated NOTCH INDICATES washer head socket pin screws (C) as shown in FRONT OF PROJECTOR SHOULDER figure 3.1. Tighten using 4 mm allen wrench (B). AA C fig. 3.1 Flip projector upside down and attach adapter plate (AA) using three serrated socket pin screws (BB) and retai
Resumo do conteúdo contido na página número 9
Attaching Adapter Plate to Projector Mount WARNING Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the screen. Slide connection block with projector into projector mount assembly (A) as shown. Tighten captive screw to secure 5 projector to projector mount assembly (A). ARROW INDICATES FRONT OF MOUNT FRONT OF A MOUNT CONNECTION BLOCK CAPTIVE SCREW IMPORTANT: For security installations, insert one #10-32 x 1/4"
Resumo do conteúdo contido na página número 10
Projector Alignment To adjust yaw (swivel) for wood stud, concrete ceiling, and threaded rod mounting applications: 7 Loosen wood screws (F) if flush mounted to wood joists (page 5) or concrete ceilings (page 6), or loosen locknuts on threaded rods (page 7), until projector mount can be rotated. Rotate mount to desired position and retighten screws or locknuts. To adjust yaw (swivel) for extension column applications: Loosen screw on projector mount assembly (A) indicated below until projector
