Resumo do conteúdo contido na página número 1
ATTACHMENT
OPERATOR’S
MANUAL
Clean Sweep
Triple Catcher
Clean Sweep Triple Catcher
Mfg. No. Description
1695065 Clean Sweep Triple Catcher
1732613
Rev. 00
Rev. Date 01/2006
TP 100-4268-00-AT-SMN
Resumo do conteúdo contido na página número 2
THIS PAGE INTENTIONALLY BLANK (FOR PLACEMENT ONLY - DO NOT PRINT)
Resumo do conteúdo contido na página número 3
Table of Contents Safety Rules & Information Initial Collector Assembly General Warnings............................................2 Assemble Catcher Bags ................................13 Safety Decals ..................................................2 Install Cover...................................................13 General Operating Information Removing & Re-attaching the Triple Catcher Mowing with the Triple Catcher........................3 Removing the Grass Catcher ....................
Resumo do conteúdo contido na página número 4
Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian- gle in text signifies important cautions or warnings which must be followed. GENERAL WARNINGS � Know the unit’s controls and how to stop quickly. � If the mower stalls or the collector chute plugs: READ THE OPERATOR’S MANUALS. 1. Disengage the
Resumo do conteúdo contido na página número 5
General Operating Instructions BEFORE OPERATION Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag is very important. For this reason, BEFORE YOU BEGIN MOWING you should make certain the underside of the mower and the u
Resumo do conteúdo contido na página número 6
Initial Turbo Installation Torque to 12 55-70 ft. lbs. 11 44" 24 49 35 25 10 18 29 21 1 50" 18 17 19 20 2 26 33 1 22 16 27 8 2 9 Existing Pulley 3 23 & Spacer 15 14 4 7 8 48 13 36 32 31 37 30 38 22 6 39 5 Existing 27 45 47 Hardware 46 27 34 27 8 17 38 44 22 43 28 42 Existing Hardware 41 (Bolt, Washer, Lockwasher, & Nut) Existing Hardware 40 17 2 WASHER, Flat, 3/8 34 1 WASHER,3/8 Ref.Qty. Description 1 2 CAPSCREW, Hex Head, 5/16-18 x 1 18 1 CAPSCREW, Hex Head, 3/8-16 x 2 35 1 V-BELT, 50” Turbo
Resumo do conteúdo contido na página número 7
Initial Turbo Installation TURBO INSTALLATION Remove Mower Deck Remove the mower deck from the unit (see Operator’s Manual for instructions). A Deflector Removal 1. Remove and retain the carriage bolts, washers, lock- washers, and nuts (A, Figure 3) holding the deflector rod to the deck. Remove and discard the deflector Figure 3. Remove Deflector rod. Retain the deflector. A. Carriage Bolts, Washers, Lockwashers, & Nuts Install Discharge Baffle B 1. Attach the baffle bracket (A, Figure 4) und
Resumo do conteúdo contido na página número 8
Initial Turbo Installation Install Deflector B 1. See Figure 6. Drill four 13/64” holes from the bottom of the deflector at the pre-molded drill points (A, bot- tom of deflector). 2. Attach the deflector to the support rod wire-form using four #10-14 x 3/4 truss head screws and nylock nuts. A C Figure 6. Install Deflector A. 13/64 Hole Locations C. Screws, #10-24 x 3/4 B. Nylock Nuts Install Belt Guide C E 50” Models 1. See Figure 7 & 8. Locate the taptite screw that will be replaced by capsc
Resumo do conteúdo contido na página número 9
Initial Turbo Installation Torque to E 55-70 ft. lbs. B D D E Original F Pulley and Spacer C B C A A Figure 9. Install Idler Assembly A. Idler Assembly. D. Locknuts, 5/16-18 Figure 10. Install Turbo Drive Pulley B. Belt Guide E. Taptite Screws A. Original Pulley & Spacer D. Spring Washer C. Capscrew, 5/16-18 x 7/8 B. Spacer, W/Notches (New) E. Sleeve Nut C. Pulley (New) F. Spacer (New) Install Idler Assembly & Belt Guide 1. See Figure 9. Remove and discard the two taptite screws from location
Resumo do conteúdo contido na página número 10
Belt Cover Initial Turbo Installation C B B A 50" D A 44" E Figure 13. Belt Cover Plates F A. Belt Cover Plate for 50” Mower B. Belt Cover Plate for 44” Mower Figure 14. Install Belt Cover Plate WARNING A. Belt Cover Latch E. Support Bracket When the turbo blower assembly is removed from B. Belt Cover Plate F. Nylock Nut, 5/16 the mower deck, the deflector MUST be properly C. Capscrew, 5/16-18 x 1 D. Washer, 5/16 installed. Install Belt Cover Plate 1. Attach the belt cover plate (B, Figure 1
Resumo do conteúdo contido na página número 11
Initial Turbo Installation Install Turbo Blower D E 1. Install the turbo unit by sliding the turbo pivot rod into the pivot bracket at the front edge of the mower deck (A, Figure 17). C B 2. Tilt the deflector (B) UP. 3. Rotate the turbo unit (C) into position on the dis- A charge of the mower deck, and “latch” the slot in the turbo housing over and onto the anchor bracket at (D). Tighten the wing nut (E) to secure. Figure 17. Install Turbo Blower A. Pivot Bracket D. Anchor Bracket B. Deflector
Resumo do conteúdo contido na página número 12
Initial Counter Balance & Weight Carrier Installation B A. Rear Deck Lift Lever D B. Trunnion (Existing) C C. Hair Pin (Existing) A D. Spacer, Spring (New) E E. Spring (New) F. Washer (New) F L G. Plate, Spring Support (New) H. Spacer (Existing) I M I. Eyebolt (Existing) J J. Washer (Existing) K. Capscrew (Existing) G L. Nut (Existing) M. Mower Deck H K Figure 1. Counter Balance Installation C A COUNTER BALANCE & WEIGHT CARRIER INSTALLATION C Counter Balance Installation B 1. Remove hair pin (
Resumo do conteúdo contido na página número 13
Initial Hitch & Tube Installation D D A E A D B F C D F D B C C Figure 1. Install Hitch Plate (Flat Style Bumper) A. Hitch Plate D. Locknuts, 1/2-13 Figure 2. Install Hitch Plate (Tube Style Bumper) B. Heat Shield E. Upper & Lower A. Hitch Plate C. U-Bolts C. Capscrews Hex, Bumper B. Bumper, Tube D. Locknuts, 3/8-16 1/2-13 x 1-1/4 F. existing Holes HITCH & TUBE INSTALLATION Install Hitch Plate and Back Plate G I Flat Style Bumper 1. Remove and discard hardware holding heat shield H E (B, Fig
Resumo do conteúdo contido na página número 14
Initial Hitch & Tube Installation A A B Figure 6. Upper Tube Length A C B C D B Figure 7. Mount Deflector and Tube Pivot Figure 4. Install Back Plate (Flat Style Bumper shown) A. Tube Pivot C. 5/16” Mounting Hardware A. Back Plate and Support C. Hitch Plate B. Deflector B. Hair Pin D. Rod G D C H A E L B I F E M J A. Deflector F. Locknut, 5/16-18 K. Capscrew, N B. Back Plate G. Upper Tube #10-32 x 1/2 C. Capscrew, H. Middle Tube L. Nut, #10-32 K 5/16-18 x 1 I. Lower Tube M. Clip D. Socket J.
Resumo do conteúdo contido na página número 15
Initial Collector Assembly G A H F B E B A D C Figure 2. Install the Bags A. Bags B. Back Plate Figure 1. Assemble Catcher Bags A. Clip E. Clamp B. Cloth Bag F. Nut C C. 5/16-18 x 3/4 Carriage Bolt G. Lockwasher D. Hanger Bracket H. Wire Hoop A COLLECTOR ASSEMBLY Assemble Catcher Bags 1. See Figure 1. Insert the wire hoop (H) through the cloth bag (B). 2. Install the clamp (E) and hanger bracket (D). Secure with two 5/16-18 x 3/4 carriage bolts (C), lockwashers (G) and nuts (F). B Install C
Resumo do conteúdo contido na página número 16
Removing & Re-attaching Grass Catcher A A B D C C B Figure 1. Remove the Cover A. Cover C. Hinge B. Hinge Pin D. Hair Pin Clip D Figure 3. Install Back Plate (Flat Style Bumper shown) A. Back Plate & Support C. Hitch Plate B. Hair Pin D. Rod A Figure 2. Remove the Bags A. Bags REMOVING & RE-ATTACHING THE A GRASS CATCHER Removing the Grass Catcher & Tubes C 1. Remove the hair pin clips (D, Figure 1) and hinge B pins (B) and remove the cover (A). To Turbo Blower 2. Remove the bags (A, Figure 2)
Resumo do conteúdo contido na página número 17
Removing and Re-attaching Grass Catcher A A B C B Figure 6. Bags A. Bags B. Back Plate D C Figure 5. Install Back Plate (Flat Style Bumper shown) A. Back Plate & Support C. Hitch Plate A B. Hair Pin D. Rod Re-attaching the Grass Catcher 1. Set the back plate and support (A, Figure 5) onto pins of hitch plate (C). Secure with rod (D) and hair pin (B). 3. Hook the bags (A, Figure 6) on the back plate(B). 4. Install the catcher cover (A, Figure 7 & 8) and secure with the hinge pins (B) and hair
Resumo do conteúdo contido na página número 18
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.SimplicityMfg.com Simplicity Mfg. Inc. - Snapper Products Simplicity Mfg. Inc.500 N Spring 535 Macon Street Street / PO Box 997 McDonough, GA 30253 Port Washington, WI 53074-0997 www.Snapper.com www.MasseyLawn.com © Copyright 2006 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA.
