Resumo do conteúdo contido na página número 1
Installation Instructions / Warranty
Metris S Talis S Focus S Solaris E
04135XX0 04136XX0 04137XX0 04138XX0
Allegro E Metro E Swing C
04139XX0 04140XX0 04143XX0
Metris S Talis S Focus S Solaris E
04126XX0 04127XX0 04128XX0 04129XX0
Allegro E
Metro E
Swing C
04130XX0
04131XX0
04134XX0
Resumo do conteúdo contido na página número 2
Two-hole thermostatic tub filler -- requires rough 04125181 04135XX0 04136XX0 04137XX0 04138XX0 04139XX0 04140XX0 04143XX0 2
Resumo do conteúdo contido na página número 3
Three-hole thermostatic tub filler -- requires rough 04124181 04126XX0 04127XX0 04128XX0 04129XX0 3
Resumo do conteúdo contido na página número 4
04130XX0 04131XX0 04134XX0 Technical Information Recommended water pressure 45 - 72 psi Recommended hot water temp. 120 � - 140 � F* Max. hot water temp 165 �F* Max. flow rate 8 gpm Max. flow rate – handshower 2.5 gpm Safety stop 100° F *Please know and follow all applicable local plumbing codes when setting the temperature on the water heater. Installation Considerations • For best results, Hansgrohe recommends that this unit be installed by a licensed, profes- sional plumber. • Please read ove
Resumo do conteúdo contido na página número 5
Install the valve trim Push the escutcheon over the valve. Install the handle. Tighten the screw with a 3 mm Allen wrench. The screw must engage the slot on the cartridge. Justify the handle. Set the high temperature limit stop. slot Install the spout Remove the plug. Push the spout sealing ring firmly into the spout adapter (1). Push the escutcheon and spout over the adapter and sealing ring (2). 3 Tighten the screw using a 3 mm Allen wrench (3). 2 Do not over tighten the set screw. O
Resumo do conteúdo contido na página número 6
Install the handshower Pull the end of the handshower hose from the holder. Push the escutcheon over the end of the hose. Push the elbow firmly over one end of the handshower hose. Tighten the hose nut. Thread the hose down through the handshower holder escutcheon and handshower holder. Tighten the escutcheon over the handshower holder. Place the screen washer in the end of the elbow. Connect the handshower to the elbow. Lower the handshower and elbow into the holder. 6
Resumo do conteúdo contido na página número 7
Set the high temperature limit stop Turn the water on to the tub spout or handshower. Use a 3 mm Allen wrench to loosen the handle screw. Remove the handle from the valve. Carefully remove the retainer clip and the limit stop ring. Turn the temperature control stem until the water is the desired high temperature, usually 110°F* . Turn the stem clockwise to make the water cooler, turn it counter-clockwise to make the water warmer. *Know and follow all applicble local plumbing codes w
Resumo do conteúdo contido na página número 8
Install the stop ring so that it is against the stop -- you should not be able to turn the stem further counter-clockwise. Install the retainer clip. Install the handle. Tighten the screw. Justify the handle. Justify the handle Turn the water on to the tub spout or handshower. Place a thermometer in the water stream. Turn the temperature control knob until the output wa- ter temperature is 100°F. Turn the water off. 8
Resumo do conteúdo contido na página número 9
Loosen the handle screw with a 3 mm Allen wrench. Remove the handle. Hold the handle lever in one hand. With the other hand, turn the temperature control knob until the 100° mark is next to the indexing mark on the handle. Install the handle on the valve. Tighten the screw. 9
Resumo do conteúdo contido na página número 10
User Instructions - ThermoBalance valve Turn the lever clockwise to send the water to one function, counter-clockwise to send the water to the second function. The center position is off. Turn the temperature control knob clockwise to function 2 make the water cooler. Turn the knob counter-clockwise to make the water warmer. function 1 The knob will stop at the 100° position (the safety stop). To override the stop, press the knob down and continue turning it counter-clockwise. User I
Resumo do conteúdo contido na página número 11
If scale deposits build up on the spray face, pour about ¾" of a commercial scale remover, such as LimeAway™ or CLR™, into a shallow dish. Follow the label instructions with regard to dilution. Soak the spray face for the amount of time specified in the label instructions. Rinse the handshower with clear water. Install the handshower. Turn on the water and flush the hand- shower for at least one minute. Maintenance: Clean the filters Turn off the water at the main before opening the val
Resumo do conteúdo contido na página número 12
Grasp the wrench flats on the cartridge stop unit with a wrench. Hold the stop unit still with one wrench. Use a second wrench or a 17mm deep socket wrench to unscrew and remove the thermostatic cartridge. Failure to hold the stop unit steady may result in damage to the ceramic plates. Rinse the debris from the filters, using a soft toothbrush if necessary. Do not at- tempt to remove the screens. Lubricate the o-rings with white plumbers grease. Hold the stop unit steady. Install th
Resumo do conteúdo contido na página número 13
Replacement parts 1 6 2 13 8 8 7 15 14 8 16 12 15 14 8 12 5 4 13 13 15 15 14 14 8 12 8 12 3 16 15 17 8 18 12 13
Resumo do conteúdo contido na página número 14
1 Solaris E handle 88530XX0 2 Talis S handle 88549XX0 9 3 C handle 88610XX0 4 Metris S handle 88713XX0 11 5 Focus S handle 88714XX0 10 6 Allegro E handle 88719XX0 7 Metro E handle 88721XX0 8 handle escutcheon 88734XX0 9 elbow 28071XX0 10 handshower escutcheon 97159XX0 11 check valve 94074000 19 12 spout sealing ring 88512000 13 aerator 13956XX0 14 spout escutcheon 97779XX0 15 screw 96029000 16 aerator 13914XX0 17 C spout 88604XX0 18 escutcheon for C spout 88735XX0 20 19 S 100 3-Jet handshower 28
Resumo do conteúdo contido na página número 15
Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning. Cleaning Materials for Faucets and Showers Acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the follow- ing points when cleaning fauce
Resumo do conteúdo contido na página número 16
maintenance, misuse, abuse, negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no-rinse” cleaning products, or the use of the product in any manner contrary to the product instruc- tions. (3) Conditions in the home such as excessive water pressure or corrosion. C. Labor or other expenses for the disconnection, deinstallation, or return of the product for warranty service, or for installation or reinstallation of the product (including but not limited
