Manual do usuário Fujitsu FTP-632MCL003

Resumo do conteúdo contido na página número 1

24V DRIVE, HIGH SPEED LINE
THERMAL PRINTER
3” MECHANISM, WITH OR WITHOUT CUTTER
FTP-632MCL001/002/303/304
n OVERVIEW
FTP-632MCL/FTP-622DCL Series is an ultra high speed line
thermal printer driven by 24 VDC, printing on 3-inch wide paper
(80 mm/85 mm).
This printer is compact and light weight, and the design allows
easy head maintenance, head cleaning and head replacement.
This printer is suitable for a variety of applications, such as POS
terminals, ticket machines, coupon machines, label prin

Resumo do conteúdo contido na página número 2

FTP-632MCL001/002/303/304 n DESIGNATION Item Part number Printer mechanism *1 Standard FTP-632MCL001/002 Printer mechanism with cutter *1 FTP-632MCL303/304 Parallel (Centronics Standard) *2 Interface board FTP-622DCL001/011 *3 Serial (RS232C) FTP-622DSL001/011/012 *4 FTP-622CU101 LSI(MCU) Thermal head cable Cables FTP-622Y001 Parallel interface cable FTP-622Y201 Serial interface cable FTP-622Y301 Power cable FTP-622Y401 *1: 001/303 is for front paper insertion (curl path) and 002/304 is for rear

Resumo do conteúdo contido na página número 3

FTP-632MCL001/002/303/304 (Continued) Item Specifications Part number FTP-632MCL001/002 FTP-632MCL303/304 TM Interface Centronics (ESC/POS ), RS232C 24 VDC ± 5%, Voltage 2 * Current : average ( ): Peak For head 1.11 (1.45) A (at 80 mm/s printing speed, 25% printing ratio) 0.81 (1.45) A (at 50 mm/s printing speed, 25% printing ratio) 0.75 (0.87) A (at 30 mm/s printing speed, 25% printing ratio) Power supply For motor 24 VDC ± 5%, 1.0 A maximum For cutter --- 24 VDC ± 5%, 1.0 A maximum For log

Resumo do conteúdo contido na página número 4

3-MOUNTING HOLE (M2) 2-POSITIONING HOLE FTP-632MCL001/002/303/304 n DIMENSIONS Mechanism FTP-632MCL001/002 PAPER INSERTION(MCL001) 20.1 HEAD UP LEVER(AT HEAD DOWN) CENTER OF PAPER PAPER INSERTION (MCL002) HEAD CONNECTOR 76.8(POSITIONING HOLE PITCH) + 1 – 50.9 57.0 Unit: mm (107.9) Interface board 130.8 120.7 116.8 87.6 19.1 5.1 5.1 CN2** CN5 CN3 4—ø3.6 CN10 CN11* CN13 5.1 5.1 43.2 95.4 105.4 120.7 *CN11 on FTP-622DCL011/111 & 622DSL011/112 only Unit: mm **CN2 on FTP- 622DSL only 4 88.9 (250

Resumo do conteúdo contido na página número 5

FTP-632MCL001/002/303/304 n DIMENSIONS Mechanism FTP-632MCL303/304 (cutter cable) (motor cable) Unit: mm Interface board 130.8 120.7 116.8 87.6 5.1 5.1 19.1 CN2* CN5 CN3 4-Ø3.6 CN11 CN13 CN10 5.1 5.1 43.2 86.4 105.4 120.7 Unit: mm *CN2 on FTP-622DSL only 5 88.9 78.7 39.4 5.1 5.1 3-2.0 or less CN1 CN8 39.4 5.1 5.1 (sensor cable)

Resumo do conteúdo contido na página número 6

FTP-632MCL001/002/303/304 n CONNECTOR PIN ASSIGNMENT FOR PRINTER MECHANISM 1. Thermal Head Head side : B16B-PH-K-S-2.2 (J.S.T.) or equivalent Board side : PHR-16 (J.S.T.) or equivalent *1: Symbol: " " means a negative logic signal Thermal head heat sink Head up level Motor 1, 2, 3, ......................................15, 16 Connector Pin No. 2. Motor connectors 3. Sensor connectors Motor side : PHR-4 (J.S.T.) or equivalent Sensor : PHR-5 (J.S.T.) or equivalent Board side :

Resumo do conteúdo contido na página número 7

FTP-632MCL001/002/303/304 4. Cutter Mech side : EHR-4 (J.S.T.) or equivalent Board side : B4B-EH (J.S.T.) or equivalent n FUNCTION ITEM ITEM 1. Test printing 8. Cutter trouble detection 2. Paper-out detection 9. Motor power save 3. Paper near end detection 10. Mark detection 4. Head-up detection 11. MCU trouble detection 5. Abnormal temperature detection of thermal head 12. Power on/off sequence protection 6. Blown fuse detection 13. Motor protection 7. Abnormal voltage detection of head