Resumo do conteúdo contido na página número 1
®
LAMP REPLACEMENT
INSTRUCTIONS
Replacement Lamp Kit
PK-CL200U
WARNING:
This Lamp Kit is for use only with JVC model
AV-61S902.
LCT0811-001A
Resumo do conteúdo contido na página número 2
The following instructions will tell you how to safely replace the projection lamp. Please read these instructions fully before attempting to replace the lamp. If you feel unsure about replacing the lamp, call a service technician. WARNING! It is very important you DO NOT TOUCH THE GLASS SURFACE OF THE NEW LAMP. Touching the glass surface will deposit oils from your hand onto the lamp surface. When the lamp heats up to operating temperature, the oil will cause a difference in temperature on th
Resumo do conteúdo contido na página número 3
Check the accessories Check that nothing is missing. The kit will include: • High-Pressure Mercury Lamp • Hex Wrench • Replacement Instructions • Recycling Information Sheet • Pre-paid shipping label Replacing the Lamp 1) Turn the television off. Press the Power button on the remote control or television’s front panel to turn the television off. Wait until the picture has closed and the LED lights on the front panel have stopped blinking indicating the lamp cool-down cycle is complete. Warn
Resumo do conteúdo contido na página número 4
3) Remove the left speaker panel. The next step is to remove the left speaker panel locat- ed at the bottom of the front 1. Pull of the television cabinet. Make sure the television is unplugged (see steps 1 and 2) before removing the 2. Lift speaker panel. To remove the panel - Grab Speaker the panel from the side near Panel the top. Gently pull the top away from the television. When the top part of the speaker panel is fully away from the television, lift up. The panel will come away from the
Resumo do conteúdo contido na página número 5
5) Removing the filter assembly. Next you will need to remove the filter Interlock switch assembly. To remove the assembly, use a coin to loosen the three large- slotted screws fastening the filter Coin etc. assembly. When the screws have been loosened, slide the filter assembly out to remove it. • Do not touch the surface of the filter Filter unit or try to remove it from the filter Filter assembly. These actions could damage the filter. If the filter is damaged, call a service technician to r
Resumo do conteúdo contido na página número 6
6) Removing the lamp assembly. Using the hex wrench included with the replacement lamp, loosen the two hex screws fastening the lamp assembly unit. Remove the screws and set aside. When the screws have been removed, remove the lamp assembly by grabbing the handle and sliding the assembly towards you. 7) Install the new lamp unit Slide the new lamp assembly into the television by holding the han- dle attached to the unit. When the new lamp assembly is securely installed inside the television, Han
Resumo do conteúdo contido na página número 7
8) Install the filter unit. Position the filter assembly back into its place, being careful not to touch the surface of the filter. Position the three screws and tighten using an correct-sized coin. 9) Reinstall the filter cover. Place the filter cover over the filter. Insert the four screws and tighten them using the screwdriver. 10) Reinstall the speaker cover. Replace the bottom of the speaker cover first. Insert the two pegs located at the bottom of the cover into the holes at the bottom lip
Resumo do conteúdo contido na página número 8
Warning Messages If the lamp replacement was successful, the television will operate normally. If there was a problem with the installation, one of several messages may display on the front panel LED lights. Lamp installed on a slant or not fully inside the television. If the lamp assembly has been installed into the unit slanted (not flat) or is not fully inserted into the lamp housing inside the television, when the television is turned on the ON TIMER and POWER light will flash. The 10 LEDs w
Resumo do conteúdo contido na página número 9
Warranty For Canadian model televisions, see the separate sheet for Canadian Warranty information. JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase for the period shown below. (“The Warranty Period”) 6 Months or PARTS 1 YEAR LABOR 1 YEAR LAMP 2000 Hours* * whichever comes first. THIS LIMITED WARRANTY IS VALID ONLY
Resumo do conteúdo contido na página número 10
Warranty 4. Damage that occurs in shipment, due to an act of God, and cosmetic damage. 5. Signal reception problems and failures due to line power surge. 6. Products used for commercial purposes (including but not limited to rental). *7. Lamp is covered for 6 months or 2000 hours from date of purchase (whichever comes first). Labor to replace lamp is not included upon expiration of the lamp warranty period. 8. Accessories. 9. Batteries (except that Rechargeable Batteries are covered for 90 day
Resumo do conteúdo contido na página número 11
Authorized Service Centers QUALITY SERVICE HOW TO LOCATE YOUR JVC SERVICE CENTER TOLL FREE: 1 (800) 252-5722 http://www.jvc.com Dear Customer, In order to receive the most satisfaction from your purchase, please read the instruction booklet before operating the unit. In the event that repairs are necessary, please call 1 (800) 252-5722 or visit our website at www.JVC.com. Remember to retain your Bill of Sale for Warranty Service. Do not service the television yourself Caution To prevent electric
Resumo do conteúdo contido na página número 12
JVC COMPANY OF AMERICA JVC CANADA, INC. Division of JVC Americas Corp. 21 Finchdene Square 1700 Valley Road Scarborough, Ontario Wayne, New Jersey, 07470 Canada, M1X 1A7
