Resumo do conteúdo contido na página número 1
This Manual is Bookmarked
This Manual is Bookmarked
Owner's Manual
Cold Saw
Models: FK350-2, FK350-2SX, FK350-4, FK350-4SX
FK350 FK350-SX
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60124 Part No. M-FK350-2
Ph.: 800-274-6848 Revision B 02/07
www.wmhtoolgroup.com Copyright © WMH Tool Group
Resumo do conteúdo contido na página número 2
Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your WILTON® tools. For the name of an Authorized Service Center in your area call 1-800
Resumo do conteúdo contido na página número 3
Table of Contents Warranty and Service....................................................................................................................................2 Table of Contents..........................................................................................................................................3 Warnings .......................................................................................................................................................4 Introduct
Resumo do conteúdo contido na página número 4
Warnings 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. The cold saw is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a cold saw, do not
Resumo do conteúdo contido na página número 5
23. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 24. Maintain a balanced stance at all times so that you do not fall into the blade or other moving parts. Do not overreach or use excessive force to perform any machine operation. 25. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the
Resumo do conteúdo contido na página número 6
Introduction The FK350 and FK350-SX are circular saws designed to provide a reliable solution to the needs of machine shops and production environments that work with steel or iron. The FK350 is manually operated: after clamping the material in the vise, the operator presses the trigger handle starting the blade, and brings the operating lever downward to cut the material. The SX offers both semi-auto and manual mode. When in semi-auto mode, operator positions material, and then presses the
Resumo do conteúdo contido na página número 7
FK350 Features FK350 Cold Saw FK350-SX Cold Saw 7
Resumo do conteúdo contido na página número 8
Features Miter Cutting Head The miter cutting head is the unit that cuts the material and consists of a cast iron base, blade support unit and guard, transmission unit, and motor. The depth of cut is set by adjusting the depth cut stop. The miter cutting head swivels and locks into -45º, 90º, and +45º by means of a locking mechanism. Depressing the mechanism overrides the lock, permitting the head to adjust Figure 1 to any position between -45º and +45 . Flood Coolant System Miter Po
Resumo do conteúdo contido na página número 9
Installation Electrical Connections All electrical connections Unpacking the machine must be done by a qualified electrician. All adjustments or repairs must Do not handle the packed be done with the machine disconnected from machine using slings. the power source, unplugged. Failure to comply may result in serious injury! To install the machine, first remove the packing, paying particular attention not to cut any electric FK350-2 and FK350-2SX are rated at 220V. wires or hydraulic
Resumo do conteúdo contido na página número 10
Control Panel – FK350-SX Controls Emergency – Emergency Stop: This turns off the controls, and the machine. When used, it Control Panel – FK350 requires that “Control On” button be pushed. The Control Panel (Figure 4) is located on the Vise – Open/Close (Manual mode front the cabinet stand and consists of the Mode selection – Select Semi-auto, or Manual Power and High/Stop/Low switches, described mode. below. Start – In manual mode, this starts the saw Power Switch – The Power switch
Resumo do conteúdo contido na página número 11
Operation Before using the machine: Check that safety devises (ex., blade guards) are in position and work perfectly and that personal safety requirements are complied with. Check the sharpness of the blade and verify FK350-SX coolant flow. To operate machine, FK350 1. Clear the Emergency Stop. 2. Press Control On. 1. Make sure the work piece is securely clamped in the vise. 3. Select the desired blade speed. 2. Turn the power on (A, Fig. 8). 4. Select Manual or Semi-auto. 3. Sel
Resumo do conteúdo contido na página número 12
Miter Adjustment The adjust the miter position follow the steps below while referring to Figure 10: 1. Move the miter position lock (A) to the right to release. 2. Adjust the head to the desired angle ranging from –45º to +45º by pushing on the back of the motor to the right or left. The miter position is shown on the scale (B). 3. A detent mechanism locks the head in the -45º, 90º and +45º positions and will prevent the head from rotating. For a miter position other than -45º, 90º a
Resumo do conteúdo contido na página número 13
Air Prep Unit – FK350-SX only Maintenance The Air Prep Unit regulates the air pressure supplied to the saw. It is located in the cabinet Maintenance Requirements stand and is accessible through the access door located below and to the left of the control panel. All maintenance must be Referring to Figure 13, it consists of a pressure carried out with the power switched off. regulator, pressure gauge, water trap and Failure to comply may result in serious lubricator. Air pressure (90lbs.
Resumo do conteúdo contido na página número 14
Lubrication For long life and trouble free operation, it is essential that this machine is kept well lubricated. The vice and leadscrew should be oiled daily. Pivot joints and bearings should be greased weekly Check the gearbox oil level weekly, full level is top of sight glass with head in full up position. The gearbox oil should be changed annually, and the hydraulic fluid [FK350-SX] should be changed annually. Recommended Lubricants: Gearbox Use Texaco Meropa 460 or equivalent. Gre
Resumo do conteúdo contido na página número 15
Blade Selection When using the FK350 cold saw, it is important to select the correct type of blade for the material to be cut. This section explains the limitations and specific applications of the different types of blades. General Characteristics: Fine Tooth Pitch --used for thin wall materials such as sheet steel, tubes and profiles Coarse Tooth Pitch --used for large cross- sections -- for soft materials (aluminum alloys and soft alloys in general). Determining Proper Tooth Pitch
Resumo do conteúdo contido na página número 16
Blade Structure For non--ferrous metals, it is common to use circular saws with brazed hard metal HM cutting edge, consisting of a disc made of alloy tool steel (71Cr1) on which the shape of the teeth and the seats for the cutting edges are made of Widia K10. These saws have shown excellent wear resistance but low resistance to impact, which is in any case a minor problem with non- ferrous materials. Figure 14 ”BW” TYPE SHARPENING DIN 1838--UNI 4014 Coarse toothing with teeth alternate
Resumo do conteúdo contido na página número 17
Figure 17 Figure 19 Short swarf material such as brass, bronze, Circular saws can also be characterized by other aluminum and hard cast iron require smaller parameters such as the whine reduction feature, cutting angles because the swarf becomes which cuts down noise at high speeds, or crushed immediately and the rake angle has expansion, which compensates for the pushing little effect during the cutting stage. of chips inside the cutting edge, thus reducing the thrust on the walls o
Resumo do conteúdo contido na página número 18
Troubleshooting Troubleshooting – Blade and Cutting Problems Problem Probable Cause Solution Incorrect lubricant/coolant fluid Ensure proper coolant flow. Check the cutting speed, feed speed and air pressure Material too hard parameters and the type of blade you are using. With a new blade it is necessary to start cutting at half feeding speed. After the wearing--in period (a cutting Disc not worn--in correctly surface of about 300 cm2 for hard materials and about 1000 cm2 for soft mate
Resumo do conteúdo contido na página número 19
Troubleshooting – Machine Fault & Operating Problems Problem Probable Cause Solution Check: the phases; the cables; the plug; the socket. Electrical power supply Also check that the motor connections are in place. Check that the voltages are present both on the input Transformer and output. Otherwise replace. Check that the phases in it are present both on the input and output, that it is not jammed, that it closes Contactor when powered and that it is not causing short circuits. Chan
Resumo do conteúdo contido na página número 20
Head Assembly – FK350 & FK350-SX Index No. Part No. Description Size Qty 1 ...............FK350-201 ...............Head Body ........................................................... .................................... 1 2 ...............FK350-202 ...............Spindle ................................................................. .................................... 1 3 ...............FK350-203 ...............Spindle Housing................................................... ........
