Resumo do conteúdo contido na página número 1
NETWORK CAMERA
Model: IK-WD14A
Quick Start Guide and Important Safeguards
This guide describes the hardware installation.
Refer to the user's manual (PDF file) contained in the CD-ROM for settings, operations
and other information.
The application Adobe Reader is needed to view PDF files. If you do not have this
application, download it from the Adobe Systems Incorporated website.
n http://www.adobe.com/
For information on our latest products and peripheral devices, refer to the following
Web
Resumo do conteúdo contido na página número 2
Introduction FCC (USA)-INFORMATION NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Howeve
Resumo do conteúdo contido na página número 3
Thank you for purchasing the IK-WD14A Network Camera. Before using the camera, read this quick start guide carefully to ensure correct usage. After reading this quick start guide, save it for future reference. The design, specifications, software, and quick start guide contents are subject to change without prior notice. Terms and Trademarks l The term "OS" is used in this manual to indicate operating systems compatible with this product. -- Windows XP: Microsoft Windows XP operating syste
Resumo do conteúdo contido na página número 4
Table of Contents Introduction 2 FCC (USA)-INFORMATION .......................................................................................2 Terms and Trademarks ..............................................................................................3 Table of Contents.............................................................................................. 4 Important Safeguards ....................................................................................... 5 Important Safe
Resumo do conteúdo contido na página número 5
Important Safeguards 1. Read Instructions Read all the safety and operating instructions before operating the product. 2. Retain Instructions Retain the safety instructions and user's manual for future reference. 3. Warnings Comply with all warnings on the product and in the user's manual. 4. Follow Instructions Follow all operating and use instructions. 5. Cleaning Disconnect this camera from the power supply before cleaning. 6. Attachments Do not use attachments not recommended by the camera m
Resumo do conteúdo contido na página número 6
13. Lightning For additional protection on this camera during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the power supply and cable system. This will prevent damage to the camera due to lightning and power-line surges. If lightning occurs, do not touch the unit or any connected cables in order to avoid electric shock. 14. Overloading Do not overload the power supply or extension cords as this can result
Resumo do conteúdo contido na página número 7
Important Safeguards (Cont.) CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclama
Resumo do conteúdo contido na página número 8
Notes on Use and Installation l Do not aim the camera at the sun Never aim the camera at the sun even with the camera power off. l Do not shoot intense light Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may appear on the screen. However, this is not a malfunction. l Treat the camera with care Dropping or subjecting the camera to intense vibration may cause it to malfunction. l Never touch internal parts Do not touch the internal parts of the camera other than
Resumo do conteúdo contido na página número 9
Setting the Network Camera Environment Items needed for network camera monitoring Administrator's personal computer l The personal computer that allows setting, operating, monitoring and other functions with the network camera is called the "administrator's personal computer" in this guide. * The personal computer for viewing monitored images is called the "user's personal computer" in this quick start guide. The network camera can be viewed by more than one personal computer at the same t
Resumo do conteúdo contido na página número 10
Contents l IK-WD14A l AV Out cable l CD-ROM l Alignment Sticker IK-WD14 A Ver. WD14-01 P/N : 62XXXXXXXG Warranty Card Quick Start Guide and Important l l Safeguards l Torx driver l Screws and Anchors 10 10
Resumo do conteúdo contido na página número 11
Physical Description Dome Cover Internal microphone Cover screws Knock out Tilt adjustment screws Lens cover Mounting holes 1 11 1
Resumo do conteúdo contido na página número 12
CAMERA MAIN UNIT l Front View IR LEDs (SR-LED) Lens Light Sensor Focus Button Built-in Microphone Status LED Rear View l General IO Terminal Block Micro SD/ 1. GND SDHC Card 2. Power input (DC 12V) Slot 3. Power input (AC 24V) 4. Power input (AC 24V) 5. Signal GND Recessed 6. Digital Input Reset Button 7. Digital output 8. 12V DC Output DIP switch 10/100BaseT Microphone Video Output Ethernet Socket NTSC internal 60Hz MIC In (Printed "Audio In") Audio/Video Out external PAL 50Hz (Printe
Resumo do conteúdo contido na página número 13
Hardware Installation First, use the supplied driver to detach the dome cover from the camera base. Then, follow the steps below to install the camera; either to a ceiling or to a wall. Bottom of the Camera Dome Cover 13
Resumo do conteúdo contido na página número 14
Alignment sticker Notes: l The included screws and anchors are used to install the Alignment sticker camera to a solid surface. (e.g. concrete) If installing on loose or thin material surfaces , use the appropriate anchors (not included) with the screws. l Generally the camera turns a built-in microphone in the direction of object. l Install the camera securely. Mounting the camera to a solid surface (1) Attach the Alignment Sticker to the surface. (2) Drill three pilot holes (Ø0.28inch×1.
Resumo do conteúdo contido na página número 15
P P A A R R T T I I T T I I O O N N P P A A R R T T I I T T I I O O N N L L I I N N K K R R E E C C E E I I V V E E P P O O W W E E R R C C O O L L L L I I S S I I O O N N 1 1 2 2 3 3 4 4 5 5 L L I I N N K K R R E E C C E E I I V V E E P P O O W W E E R R C C O O L L L L I I S S I I O O N N 1 1 2 2 3 3 4 4 5 5 Network Deployment Power over Ethernet (PoE) l When using a PoE-enabled switch The camera is PoE-compliant, allowing transmission of power and data via single LAN cable. See the followin
Resumo do conteúdo contido na página número 16
P A R T I T I O N L I N K R E C E I V E P O W E R C O L L I S I O N 1 2 3 4 5 General Connection (without PoE) 1. Connect the camera to an Ethernet switch via LAN cable. 2. Connect the power cable from a power unit (not supplied) to the appropriate port of the general I/O terminal. (See page 12). 3. Connect the PC to an Ethernet switch via Ethernet cable. Ethernet switch 3 (not supplied) 1 Client PC (not supplied) 2 AC 120V AC24V or DC12V adapter UL Listed Class 2 power supply (not supplied) NO
Resumo do conteúdo contido na página número 17
Assigning IP Address 1. Install the "Installation Wizard" under the Software Utility directory from the CD- ROM. 2. The program will analyze your network environment. After your network is analyzed, please click on the "Next" button to continue the program. Installation Wiza rd 3. The program searches for other Network Cameras on the same network. 4. After searching, the main installer window will pop up. Click on the MAC address of the appropriate device to connect to the Network Camera. 00-0
Resumo do conteúdo contido na página número 18
Retrieving Images 1. Access the Network Camera from the network. ® 2. Retrieve live video through Internet Explorer . For more information on camera configuration, please refer to user's manual on the CD-ROM. 18 18
Resumo do conteúdo contido na página número 19
Adjusting the Lens Based on the live image retrieved from the camera, adjust the camera lens by performing the following: To adjust the viewing angle 1. Turn the lens module left and right. 2. Loosen the tilt adjustment screws on both side of the camera and then turn the lens module up and down. Upon completion, tighten the screws. 3. Turn the lens cover to adjust the image orientation. 2 3 o Tilt 81 1 o Pan 350 DO NOT over rotate the lens. Doing so will damage the camera lens module
Resumo do conteúdo contido na página número 20
Dome cover 1. Attach the dome cover to camera. 2. Secure the two dome screws with a screwdriver. Make sure all parts of the camera are securely installed. 2 1 The supplied screwdriver is exclusively designed to match the dome screws. Do not discard the screwdriver. 20 20
