Resumo do conteúdo contido na página número 1
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page a
INSTALLATION & USER GUIDE
For High Performance
Home Theater Reproduction
from In-Wall Locations
RIGHT, LEFT, SURROUND AND
LST-RLS/CTR
CENTER CHANNEL IN-WALL LOUDSPEAKER
Resumo do conteúdo contido na página número 2
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page b LST-RLS/CTR RIGHT, LEFT, SURROUND AND CENTER IN-WALL LOUDSPEAKER TABLE OF CONTENTS Features............................................................................................................................1 Product Overview...........................................................................................................1 Package Contents .......................................................................................
Resumo do conteúdo contido na página número 3
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page 1 FEATURES: LST-RLS FEATURES: LST-CTR ■ Dual 5-1/4” mica filled polypropylene ■ Dual 5-1/4” magnetically shielded mica woofers with butyl rubber surrounds filled polypropylene woofers with butyl rubber surrounds ® ■ 1” liquid cooled ElastoDynamic dome tweeter ■ 1” liquid cooled magnetically shielded ® ElastoDynamic dome tweeter ■ Front mounted bass and treble cut switches (-3dB) ■ Front mounted dialog enhancement switch ■ Configurable as a main
Resumo do conteúdo contido na página número 4
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page 2 PACKAGE CONTENTS TOOLS REQUIRED ■ Speaker x 1 ■ Stud Locator (for existing construction) ■ Speaker frame x 1 ■ Drywall saw (for existing construction) ■ Speaker grille x 1 ■ Pencil (for existing construction) ■ Speaker bracket x 1 ■ Cordless screwdriver with No2 Philips bit ■ Wings for new construction x 2 ■ 1/8” Slotted screwdriver x 2 ■ #6 x 1-5/8” Philips head ■ Wire stripper drywall screws x 14 ■ Wire labels ■ Speaker cutout template x 1
Resumo do conteúdo contido na página número 5
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page 3 6. Locate the cutout template. 13. Tightly twist the end of each wire until no frayed ends remain. 7. Use a pencil and the cutout template to trace the speaker outline in the desired 14. Attach the speaker wires to the speaker locations on the wall. terminal connectors. Connect the negative output from the amplifier to the 8. Use a drywall saw to cut along the black terminal. Connect the positive penciled line. output from the amplifier to t
Resumo do conteúdo contido na página número 6
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page 4 Installation New Construction: 8. In unique situations where the bracket must be located precisely next to a joist, The speaker brackets should be installed the bracket has “emergency” screw prior to the drywall. holes located on its snap-on tabs. Break 1. Attach the wings to the bracket by away two of the outer mounting tabs on snapping them into the sides of the the side you wish to affix, see Figure 3. bracket. (See Figure 1). To shorten
Resumo do conteúdo contido na página número 7
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page 5 12. The screws should pull the frame and LST-RLS Main/Surround Switch bracket together (sandwiching the The crossover on the back of the LST-RLS drywall) so that the frame is flush with enables you to configure the speaker for the wall surface. best performance as either a front “main” speaker or rear “surround” speaker. When 13. Strip 1/4” of insulation from the end of the LST-RLS is used as a surround speaker, each wire. set the switch to
Resumo do conteúdo contido na página número 8
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page 6 REMOVAL OF GRILLE OPERATION Removing the Grille Listening at Higher Volumes: If the grille is already installed, remove it by Listening at Higher Volumes: using a bent paper clip or the tip of a It requires more power to achieve a corkscrew and pulling it away from the reasonable volume of sound in a large room frame. See Figure 4. than it does in a small room. It is possible to turn the volume so high that the amplifier runs out of power. Th
Resumo do conteúdo contido na página número 9
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page 7 SPECIFICATIONS: LST-RLS Power handing: 10 – 150 watts Frequency response: 45Hz-21kHz +/- 3dB Impedance: 8 ohms Dimensions: 8-1/4” x 14-1/2” outside dimension 7-1/8” x 13-1/4” hole cutout 3-1/8” deep when installed in 1/2” drywall Warranty: 5 year limited SPECIFICATIONS: LST-CTR Power handing: 10 – 150 watts Frequency response: 45Hz-21kHz +/- 3dB Impedance: 8 ohms Dimensions: 8-1/4” x 14-1/2” outside dimension 7-1/8” x 13-1/4” hole cutout 3-1
Resumo do conteúdo contido na página número 10
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page 8 LIMITED WARRANTY A factory Return Authorization Number will JobSite Systems (“JOBSITE”), a Niles be sent to you. DO NOT RETURN ANY Audio Corporation company, warrants its UNIT WITHOUT FIRST RECEIVING passive products (those not requiring AC or WRITTEN AUTHORIZATION AND battery power) to the original purchaser to SHIPPING INSTRUCTIONS FROM be free of manufacturing defects in material JOBSITE. and workmanship for a period of ten years from date
Resumo do conteúdo contido na página número 11
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page 9 NOTES: 9
Resumo do conteúdo contido na página número 12
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page 10 JOBSITE SYSTEMS 12331 S.W. 130 STREET, MIAMI, FLORIDA 33186 P (866) 4JB-SITE (866-452-7483) – F (305) 238-0185 WWW.JOBSITESYSTEMS.COM JobSite Systems, a Niles Audio Corporation company, 12331 S.W. 130 Street, Miami, Fl 33186. ©2004 Niles Audio Corporation. JobSite, Pure Custom, ElastoDynamic and Niles are registered trademarks of Niles Audio Corporation and the JobSite Logo is a trademark of Niles Audio Corporation. All other trademarks are
