Resumo do conteúdo contido na página número 1
TS8G~16GCF600
TS8G~16GCF600 600X CompactFlash Card
TS8G~16GCF600
Features
Description
• CompactFlash Specification Version 4.1 Complaint
Dedicated to fulfilling the demanding requirements of
• RoHS compliant products
performance-conscious photographers, Transcend
• Single Power Supply: 3.3V ± 5% or 5V ± 10%
proudly releases its Extreme Plus 600X CompactFlash
o o
• Operating Temperature: -25 C to 85 C
cards with Turbo MLC technology. With its amazing
Resumo do conteúdo contido na página número 2
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Transcend Transcend Information Inc. 2 V1.0
Resumo do conteúdo contido na página número 3
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Block Diagram Transcend Information Inc. 3 V1.0
Resumo do conteúdo contido na página número 4
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Transcend Information Inc. 4 V1.0
Resumo do conteúdo contido na página número 5
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Pin Assignments and Pin Type PC Card Memory Mode PC Card I/O Mode True IDE Mode4 Pin Signal Pin Signal Pin In, Out Pin Signal Pin In, Out In, Out Type Pin Num Num Name Type Name Type Type Num Name Type Type 1 GND Ground 1 GND Ground 1 GND Ground 2 D03 I/O I1Z, OZ3 2 D03 I/O I1Z, OZ3 2 D03 I/O I1Z, OZ3 3 D04 I/O I1Z, OZ3 3 D04 I/O I1Z, OZ3 3 D04
Resumo do conteúdo contido na página número 6
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 PC Card Memory Mode PC Card I/O Mode True IDE Mode4 Pin Pin In, Out Pin Pin In, Out Pin Pin In, Out Signal Name Signal Name Signal Name Num Type Type Num Type Type Num Type Type 7 -HIOE -HIOE -HIOE 10 10 8 34 HSTROBE I I3U 34 HSTROBE I I3U 34 HSTROBE I I3Z 11 11 9 HDMARDY -HDMARDY -HDMARDY 7 -IOWR -IOWR -IOWR 35 I I3U 35 I I3U 35 I I3Z 10,11 10,11 8,9
Resumo do conteúdo contido na página número 7
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Input Leakage Current Note: In Table 1 below, x refers to the characteristics described in table 2. For example, I1U indicates a pull-up resistor with a type 1 input characteristic. Table 1: Input Leakage Current Type Parameter Symbol Conditions MIN TYP MAX Units IxZ Input Leakage Current IL Vih = Vcc / Vil = Gnd -1 1 μA IxU Pull-Up Resistor RPU1 Vcc = 5.0V 50k 500k
Resumo do conteúdo contido na página número 8
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Output Drive Characteristics Table 4: Output Drive Characteristics Type Parameter Symbol Conditions MIN TYP MAX Units Vcc Voh Ioh = -4 mA -0.8V 1 Output Voltage Volts Gnd Vol Iol = 4 mA +0.4V Vcc Voh Ioh = -4 mA -0.8V 2 Output Voltage Volts Gnd Vol Iol = 4 mA +0.4V Vcc Voh Ioh = -4 mA -0.8V 3 Output Voltage Volts Vol Iol = 4 mA Gnd +0.4V Tri-State Leakage
Resumo do conteúdo contido na página número 9
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Signal Description Signal Name Dir. Pin Description A10 – A00 I 8,10,11,12, These address lines along with the -REG signal are used to select the following: (PC Card Memory Mode) 14,15,16,17, The I/O port address registers within the CompactFlash Storage Card , the 18,19,20 memory mapped port address registers within the CompactFlash Storage Card, a byte in the card's information struct
Resumo do conteúdo contido na página número 10
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Signal Name Dir. Pin Description These input signals are used both to select the card and to indicate to the card -CE1, -CE2 I 7,32 whether a byte or a word operation is being performed. -CE2 always accesses (PC Card Memory Mode) the odd byte of the word.-CE1 accesses the even byte or the Odd byte of the word depending on A0 and -CE2. A multiplexing scheme based on A0,-CE1, Card Enable -CE
Resumo do conteúdo contido na página número 11
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Signal Name Dir. Pin Description -INPACK O 43 This signal is not used in this mode. (PC Card Memory Mode except Ultra DMA Protocol Active) The Input Acknowledge signal is asserted by the CompactFlash Storage Card -INPACK when the card is selected and responding to an I/O read cycle at the address (PC Card I/O Mode except Ultra that is on the address bus. This signal is used by the host
Resumo do conteúdo contido na página número 12
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Signal Name Dir. Pin Description -IOWR This signal is not used in this mode. I 35 (PC Card Memory Mode– Except Ultra DMA Protocol Active) The I/O Write strobe pulse is used to clock I/O data on the Card Data bus into -IOWR the CompactFlash Storage Card controller registers when the CompactFlash (PC Card I/O Mode –Except Ultra Storage Card is configured to use the I/O interface. DMA P
Resumo do conteúdo contido na página número 13
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Signal Name Dir. Pin Description This signal is used during Memory Cycles to distinguish between Common -REG I 44 Memory and Register (Attribute) Memory accesses. High for Common Memory, (PC Card Memory Mode– Except Low for Attribute Memory. Ultra DMA Protocol Active) Attribute Memory Select In PC Card Memory Mode, when Ultra DMA Protocol is supported by the host and the host has enabled
Resumo do conteúdo contido na página número 14
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Signal Name Dir. Pin Description -VS1 Voltage Sense Signals. -VS1 is grounded on the Card and sensed by the Host O 33 -VS2 so that the CompactFlash Storage Card CIS can be read at 3.3 volts and -VS2 is 40 (PC Card Memory Mode) reserved by PCMCIA for a secondary voltage and is not connected on the Card. -VS1 This signal is the same for all modes. -VS2 (PC Card I/O Mode) -VS1 This sig
Resumo do conteúdo contido na página número 15
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Electrical Specification The following tables indicate all D.C. Characteristics for the CompactFlash Storage Card. Unless otherwise stated, conditions are: Vcc = 5V ±10% Vcc = 3.3V ± 5% Absolute Maximum Conditions DC Characteristics CompactFlash Interface I/O at 5.0V Parameter Symbol Min. Max. Unit Remark Supply Voltage V 4.5 5.5 V CC High level output voltage V V ─ ── ─ 0.8 V
Resumo do conteúdo contido na página número 16
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Input Power Input Characteristics for UDMA mode >4 In UDMA modes greater than 4, the following characteristics apply. Voltage output high and low values shall be met at the source connector to include the effect of series termination. Table: Input Characteristics (UDMA Mode > 4) Parameter Symbol MIN MAX Units DC supply voltage to drivers V 3.3 –8% 3.3% + 8% Volts DD3 Low to high inp
Resumo do conteúdo contido na página número 17
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Signal Interface Electrical specifications shall be maintained to ensure data reliability. Additional requirements are necessary for Advanced Timing Modes and Ultra DMA modes operations. See next sections for additional information. 10 10 Item Signal Card Host -CE1 Pull-up to V 500 K Ω ≧ R ≧ 50 K Ω and CC -CE2 shall be sufficient to keep inputs inactive Control Signal -REG when the p
Resumo do conteúdo contido na página número 18
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 state and 100 μ A high state, including pull-up resistor. The card shall be able to drive at least the following load 10 while meeting all AC timing requirements: 50 pF at a DC current of 400 μ A low state and 100 μ A high state. μ 4) Status Signals: the socket shall present a load to the card no larger than 50 pF 10 at a DC current of 400 A low state and 100 μ A high state, including pull-up res
Resumo do conteúdo contido na página número 19
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Ultra DMA Electrical Requirements Host and Card signal capacitance limits for Ultra DMA operation The host interface signal capacitance at the host connector shall be a maximum of 25 pF for each signal as measured at 1 MHz. The card interface signal capacitance at the card connector shall be a maximum of 20 pF for each signal as measured at 1 MHz. Series termination required for Ultra
Resumo do conteúdo contido na página número 20
TS8G~16GCF600 TS8G~16GCF600 600X CompactFlash Card TS8G~16GCF600 Table: Ultra DMA Termination with Pull-up or Pull down Example Printed Circuit Board (PCB) Trace Requirements for Ultra DMA On any PCB for a host or device supporting Ultra DMA: The longest D[15:00] trace shall be no more than 0.5" longer than either STROBE trace as measured from the IC pin to the connector. The shortest D[15:00] trace shall be no mo
