Resumo do conteúdo contido na página número 1
MOSFET POWER AMPLIFIERS
Installation Instructions / Owner's Manual
400MSX
600MSX
Resumo do conteúdo contido na página número 2
INTRODUCTION Congratulations on your purchase of a California state-of-the-art power amplifier. Your selection of a California car audio product indicates a true appreciation of fine musical reproduction. Whether adding to an exi sting system or including your California amplifier in a new system, you are certain to notice immediate performance benefits. KEEP YOUR SALES RECEIPT Take this time to attach your sales receipt to the manual and put in a safe place. In case of any unforeseen re
Resumo do conteúdo contido na página número 3
SAFETY PRECAUTIONS Fuse amplifier's power wire at the battery. Be sure to fuse the power wire within 12" of the car's battery. This will protect the car's battery in case of a short circuit between the power amplifier and battery. THIS IS A MUST, the amplifier's built-in fuse will only protect the power amplifier not the car's battery! Use high grade wire connectors. To ensure maximum power transfer and secure safe connections, it is recommended to use high grade connectors where needed.
Resumo do conteúdo contido na página número 4
FEATURES AND BENEFITS DC Offset Protection This circuit protects the output of the amplifier against DC voltage. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current. Short Circuit Protection The circuit protects the amplifier from damage due to a short found in the speakers or wiring. If one of the speakers or its wiring comes in contact with ground, the amplifier will shut down. To resume normal operatio
Resumo do conteúdo contido na página número 5
Power Fusing This protects the amplifier against short circuits and excessive current. Remote Turn-on Automatically turns amplifier on when connected to the head unit's remote output. The amplifier will turn on and off with the head unit to save current consumption. This control also operates the reset circuit for the amplifier's protection. It must be connected with the head unit in order to reset protection circuits. Gold Plated connections For positive contact, maximum power and signal
Resumo do conteúdo contido na página número 6
MOUNTING LOCATION Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the trunk or under the seat. Select the location in which you wish to mount the amplifier. Use caution when mounting amplifier, there are many wires, gas lines, vacuum lines, brake lines as well a
Resumo do conteúdo contido na página número 7
POWER CONNECTIONS Speaker Output B+ REM GND Fuse I IN N- -L LI IN NE E P PO OW WE ER R F FU US SE E M MO OU UN NT TE ED D W WI IT TH HI IN N 1 12 2" " R RA AD DI IO O' 'S S R RE EM MO OT TE E F FR RO OM M B BA AT TT TE ER RY Y R RE EC CO OM MM ME EN ND DE ED D T TU UR RN N- -O ON N O OU UT TP PU UT T ( (N NO OT T P PR RO OV VI ID DE ED D) ) - - + + 9 94 4..7 7 C CA AR R B BA AT TT TE ER RY Y + +1 12 2V V IMPORTANT! Before making any connections, disconnect the car's battery until the installa
Resumo do conteúdo contido na página número 8
L L R R SIGNAL CONNECTIONS Connect the output of the head unit (AM/FM cassette player, CD, or DAT) to the RCA input terminals of the amplifier. To make these connections, we recommend high quality RCA cables, which are available at your local car audio retailer. Run signal wires away from electrical wires to avoid possibility of induced noise from the car's electrical system (i.e. popping noises or engine noise). TWO CHANNEL SIGNAL CONNECTIONS LP Bass X-over Boost Level Input Hi-Level Inp
Resumo do conteúdo contido na página número 9
HIGH LEVEL CONNECTIONS (OPTIONAL) If a low level RCA signal source is not available, you may still wire the amplifier with high-level or speaker level outputs from your head unit. However, only speaker leads from a "floating ground" system may be used (see diagram below). Use the provided plug to make the following connections . Note: The speaker leads from a "common ground" head unit systems should not be connected to the hi-level input terminals of the following connections. CAUTION!
Resumo do conteúdo contido na página número 10
SPEAKER CONNECTIONS Make the speaker connections using speaker wire that is at least 10 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response. When connecting, make sure that positive (+) from the amplifier is connected to the positive (+) of the speaker, and the same for negative (-). SINGLE SPEAKER CONNECTION Speaker Output B+ REM GND Fuse 4 4 O Oh hm m S Sp pe ea ak ke ers rs (2 (2 O Oh hm m M Min inim imu um m) )
Resumo do conteúdo contido na página número 11
SETTING THE CROSSOVER AND BASS BOOST Select your crossover type and frequency. The amplifier is equipped with a built-in variable low -pass crossover network allowing you to select the desired crossover point for your subwoofers. Please refer to speaker manufactures recommended crossover point. Bass LP X-over Boost 85 40 130 0 12 Select the crossover point You can add up to 12dB bass boost by for your speakers. increasing the Bass Boost control. FINE TUNE THE SYSTEM Fine tune the a
Resumo do conteúdo contido na página número 12
TROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself. In addition, there are many components in the system that could cause various signal problems such as inducted electrical noise and engine noise. Before you can properly address the problem, you must first find the component that is
Resumo do conteúdo contido na página número 13
SPECIFICATIONS 400MSX 600MSX Max Power @ 4 Ohm 1 x 400W 1 x 600W RMS Power @ 4 Ohm 1 x 200W 1 x 300W Max Power @ 2 Ohm 1 x 600W 1 x 850W RMS Power @ 2 Ohm 1 x 300W 1 x 410W THD @ RMS Power <0.07% <0.07% Frequency Response 10Hz ~ 94Hz (at-1dB) 10Hz ~ 94Hz (at-1dB) Signal To Noise >105dB >105dB RCA Input Sensitivity 200mV ~ 8V 200mV ~ 8V RCA Input Impedance 16K Ohms 16K Ohms High Level Input Impedance 100 Ohms 100 Ohms Load Impedance
Resumo do conteúdo contido na página número 14
LIMITED WARRANTY Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser. If this product is proven to be defective within this one year period, Profile will repair it when said product is returned, with a copy of the dated sales receipt, freight prepaid to Profile. This warranty is valid only in the United States.
Resumo do conteúdo contido na página número 15
WARRANTY REPAIR POLICY In the unlikely event of product failure, the following procedures should be followed 1) The unit must be under the 1-year warranty period. 2) The unit must have no physical damage. 3) A copy of the original proof of purchase must be sent with the unit. 4) Include a brief description of the problem or failure with the unit. 5) Include the return street address and daytime telephone number. 6) Allow 2~3 weeks for rep
Resumo do conteúdo contido na página número 16
By PROFILE CONSUMER ELECTRONICS, INC. 15060 SHOEMAKER AVE SANTA FE SPRINGS, CA 90670 TEL: (562)404-9393 FAX: (562)404-9433 WWW.PROFILEUSA.COM
