Resumo do conteúdo contido na página número 1
16 Port 10/100Mbit/s
Ethernet Switch with Optional
Fiber Uplink Port
-
Product User Guide
Introduction
This Tyco Electronics auto-negotiating Fast Ethernet workgroup
switch with optional fiber uplink enables clusters of up to 16 users
to have high speed, low latency LAN connections to the corporate
network.
Local management functions such as control of port speed, duplex
mode, port trunking and VLAN membership are supported.
The optional fiber uplink module enables
Resumo do conteúdo contido na página número 2
16 Port Ethernet Switch With Optional Fiber Port Features 16 x Auto-sensing 10/100Base-T RJ-45 Ethernet ports 1 x Option slot for 100Mbit/s fiber uplink module that operates over distances of up to 2Km (multi-mode) or 15 Km (single-mode) fiber 1 x Additional 10/100Mbit/s RJ-45 port for uplinking Meets IEEE 802.3, .3u and .3x Ethernet standards Local management using an RS232 console port Management enables detailed control of each port Support f
Resumo do conteúdo contido na página número 3
16 Port Ethernet Switch With Optional Fiber Port Front Panel The front panel of the switch has 16 x RJ-45 Shielded/Unshielded Ethernet Ports, an optional fiber Ethernet 100Base-FX uplink port, a console management port and an array of LED indicators. Figure 1 – Switch with optional fiber module (SC Connector) fitted Ports RJ-45 Ports. These Ethernet RJ-45 ports support both shielded and unshielded cabling systems. The port auto- negotiates the 10/100Mbit/s net
Resumo do conteúdo contido na página número 4
16 Port Ethernet Switch With Optional Fiber Port Installation Copper and Fiber Cabling Guidelines 1. The RJ-45 ports can be connected to unshielded twisted pair (UTP) or shielded twisted pair (STP) cabling systems compliant with the IEEE 802.3u 100Base TX standard for Category 5. The cable between the switch and the link partner device (router, hub, workstation, etc.) must be less than 100 metres long. 2. The fiber link on t
Resumo do conteúdo contido na página número 5
16 Port Ethernet Switch With Optional Fiber Port Completing The Installation When the switch has been installed as specified above, then the unit can be configured as detailed below:- 1. Apply AC power to the switch. The green Power LED on the front panel should light. 2. Connect the Cat. 5/5e twisted pair cables from the network partner devices to the RJ-45 ports on the front panel of the switch. In certain cases a cross-over RJ-45 cable may be needed. When a connection is obtained, the green
Resumo do conteúdo contido na página número 6
16 Port Ethernet Switch With Optional Fiber Port LED Indicators The diagnostic LED indicators located on the front panel of the switch provide real-time information about switch status. The following table describes the LED status and meaning. LED Color Function Power Green Power on The switch is trunking to another Trunking Green compatible switch. Green The UTP port is operating at 100Mbit/s 100 The UTP port is operating at 10Mbit/s or Off no partner de
Resumo do conteúdo contido na página número 7
16 Port Ethernet Switch With Optional Fiber Port Trouble Shooting Power 1. Verify that the AC power is present and that the external fusing is correct and compliant with national requirements. The green Power LED should be lit to indicate that the switch is powered correctly. Data Problems 1. Ensure that the Ethernet partner device (switch, router, NIC etc) connected to the RJ-45 UTP port of the switch is set for auto- negotiation. If this Ethernet partner device does
Resumo do conteúdo contido na página número 8
16 Port Ethernet Switch With Optional Fiber Port Accessory Product Part Numbers The following plug-in fiber modules are available as accessory products for this switch:- Product Part Number Module with SC multimode connectors 0-1591050-0 Module with ST multimode connectors 0-1591052-0 Module with MT-RJ multimode connector 0-1591054-0 Module with SC singlemode connectors 0-1591056-0 Consult dealer for precise order codes. Optional Fiber Uplink Port Specifications Th
Resumo do conteúdo contido na página número 9
16 Port Ethernet Switch With Optional Fiber Port Product Specification Standards IEEE 802.3 10Base-T Ethernet Compliance IEEE 802.3u 100 BASE-TX Fast Ethernet IEEE 802.3u 100 Base-FX Fast Ethernet ANSI/IEEE standard 802.3 N-way Auto-Negotiation Max Forwarding 14,880 pps Ethernet port (10Mbit/s) Rate 148,800 pps Fast Ethernet port (100Mbit/s) LED Indicators Power, Trunking UTP Ports: Speed, Link Activity, Duplex / Collision Ethernet LAN 10Base-T: 2-pair UTP/STP Cat. 3, 4,
