Manual do usuário Winegard 1000

Resumo do conteúdo contido na página número 1

®
Replacement DISH 1000
LNB Assembly
www.winegard.com/mobile
For Technical Services,
email help@winegard.com or call 1-800-788-4417
2452138

Resumo do conteúdo contido na página número 2

Raising the Antenna Follow the steps below to raise the antenna for reflector, bracket, and LNB assembly removal. Pay attention to the pinch points as the antenna raises. See below. Top View Side View Pinch Point Pinch Point 1 Press [POWER], and hold for two seconds to turn on the TRAV’LER® interface box. Wait until the interface box finishes “connecting to antenna.” The TRAV’LER antenna may enter the search routine after ten seconds. 2 As the antenna raises, press [POWER] and [SELECT] at

Resumo do conteúdo contido na página número 3

Removing the Reflector and LNB Assembly 1 If converting a DIRECTV SWM Slimline antenna to a DISH TRAV’LER antenna, remove the power inserter and SWM splitter; these will not be used. 2 Remove the four reflector nuts and bolts, and remove the dish. Set the nuts and bolts aside. Reflector nut not shown 3 Disconnect the coaxial cables from the turret. Note that the D port will not be present on a SWM TRAV’LER antenna. Turret 4 Remove the bolt holding the cable harness to the unit, and detach the

Resumo do conteúdo contido na página número 4

6 Remove the bolts holding the reflector bracket to the skew housing. Reflector bracket Skew housing Stiffener If replacing a Slimline assembly with a plate NOTE DISH assembly, remove and set aside the stiffener plate inside the reflector bracket. Remove the LNB arm assembly, and set aside. 7 If replacing a Slimline assembly with a DISH assembly, remove the NOTE four bolts from the adaptor plate, and remove the adaptor plate. Adaptor plate Bolts Installing the DISH Reflector and LNB Assem

Resumo do conteúdo contido na página número 5

1 Align the four holes on the inside of the reflector bracket with the four marked holes in the adaptor plate. See image below for the holes to align with the reflector bracket and adaptor plate. The numbers on the reflector bracket and adaptor plate should match. 1 1 4 4 2 2 3 3 The bracket should be installed so that the LNB TIP arm assembly is at the bottom of this plate. 1 3 2 Replace the supplied / Allen screws through 16 these four holes, and tighten. 4 2 3 After the bracket has been

Resumo do conteúdo contido na página número 6

Setting the IDU for DISH 1000 1 Press and hold [POWER] for two seconds or until the TRAV’LER interface displays “POWER ON.” Now that the power is on, release the [POWER] button. 2 3 Press and hold the [ENTER] button for two seconds.The TRAV’LER interface will ask if you wish to enter the User Menu. Press [SELECT] to choose “Yes”; then, press [ENTER]. 4 The User Menu consists of four choices: Search Mode, Diagnostics, Installation, and Exit. Press [SELECT] until the asterisk is next to “Inst

Resumo do conteúdo contido na página número 7

If you had to raise the antenna with the emergency manual stow drive, follow the instructions below for calibrating the elevation motor. 1 From the installation menu, press [SELECT] to move the asterisk to “Calibrate EL”; then, press [ENTER]. 2 Press [SELECT] to move the asterisk to “Yes.” 3 Press [ENTER] to start the elevation calibration procedure. The LCD should now display “Calibrate EL In Progress.” 4 After a few moments, the TRAV’LER interface box will display “On EL Hard Stop?/Yes *No

Resumo do conteúdo contido na página número 8

3 Place another two sheets of void 4 Position the LNB in the center of fill in the cardboard box, and the box. Make sure the cables place the LNB on top of these are still connected to the LNB. sheets of void fill. Place an additional two sheets of Place two sheets of void fill in the 5 6 void fill in the cardboard box so cardboard box, and push these that they form an ‘X’; close the two sheets into the box so that box, and tape it closed. they cover the LNB. 7 Return the package to 31