Resumo do conteúdo contido na página número 1
General Mobile Radio Service (GMRS) General Mobile Radio Service (GMRS) General Mobile Radio Service (GMRS) General Mobile Radio Service (GMRS) General Mobile Radio Service (GMRS)
Model Model:: GMRS1100-2CH GMRS1100-2CH
Model Model Model ::: GMRS1100-2CH GMRS1100-2CH GMRS1100-2CH
Owner Owner Owner’s Man ’s Man ’s Manual ual ual
Owner Owner’s Man ’s Manual ual
EMG
PWR
F
© 2002 Audiovox Electronics Corp., Hauppauge, NY 11788 Customer Service
1-800-290-6650
Resumo do conteúdo contido na página número 2
CAUTION NEVER ATTEMPT TO CHARGE ALKALINE OR DRY CELL BATTERIES, AS BATTERIES MAY BURST CAUSING PERSONAL INJURY AND DAMAGE TO THE PRODUCT. WHEN RECHARGING NICKEL METAL HYDRIDE (Ni- MH) BATTERIES WITH THE SUPPLIED AUDIOVOX CHARGER AND WALL ADAPTER, USE ONLY AUDIOVOX-APPROVED RECHARGEABLE BATTER- IES. USE OF THE AUDIOVOX CHARGER WITH OTHER BRANDS OF BAT- TERIES IS NOT RECOMMENDED, AS BATTERY CHARGING TIMES WILL VARY WITH DIFFERENT BRANDS. REFER TO THE MANUFACTURERS INSTRUCTIONS FOR CHARGING OTHE
Resumo do conteúdo contido na página número 3
Model GMRS1100-2CH (FCC License Required) MIC SP. CHG 5 7 16 6 4 8 M 3 9 15 EMG 17 10 2 PWR 14 F 11 1 12 13 1. Battery Cover 9. Combination Transmit Indi- cator (Red)/Receive and 2. Monitor/Function Confirmation Monitor Indicator (Green) Button 10. Emergency (EMG) Button 3. Detachable Carry Clip 11. Channel SCAN Button 4. Push-To-Talk (PTT) and Func- 12. Built-in Microphone tion Confirmation Button 13. Down Channel/Volume 5. Antenna Button 6. External Speaker (SPK), Micro- 14. Function (F) Bu
Resumo do conteúdo contido na página número 4
Model GMRS 1100-2CH DISPLAY 8 1 9 2 EMG 10 3 11 4 12 5 6 13 7 14 1. Beep Tone Indicator: Icon appears when beep button confirmation tone is selected; icon disappears when tone is off. 2. Key Lock Indicator: Icon appears when the keypad is locked. This function disables keys such as channel up/down and Function (F). 3. Monitor Indicator: Icon appears when the Monitor (M) button is pressed and the channel monitor function is activated. 4. Signal Strength Indicator: Icon appears when a signal
Resumo do conteúdo contido na página número 5
11. Roger Beep Tone Indicator: This icon appears when the Roger Beep tone is on, and disapppears when the tone is not in use. 12.Small Segment Display: Indicates the CTCSS tone code (1-38) function is active for the main channel in use. 13.Dual Watch Mode Indicator: Icon appears when dual watch mode is active. 14.Voice Activated Transmission (VOX) Indicator: This icon appears when the VOX mode is activated. Equipment and Accessories Supplied 1. Radio (2) GMRS1100-2CH 2. Owners Manual (1) 12
Resumo do conteúdo contido na página número 6
Use only Audiovox-approved rechargeable batteries and charger when charging batteries internal to the unit. NOTE: To extend battery life, avoid overcharging the batteries. 3. Various Brands of Rechargeable Batteries - Use of the Audiovox charger with other brands of rechargeable batteries is not recommended, as battery charging times will vary with different brands of batteries.Refer to the manufacturers instructions for charging other brands of batteries. Installing the batteries: Battery ins
Resumo do conteúdo contido na página número 7
PWR The following guidelines will improve performance and provide longer operating times for the GMRS1100-2CH: 1. Do not mix old and new batteries. 2. The use of alkaline-type batteries is recommended to provide the longest operating time. 3. Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries. 4. If the unit is not to be used for an extended period of time, remove the batteries. Old or leaking batteries can cause damage to the unit and will void the warranty. CHARGING STAND P
Resumo do conteúdo contido na página número 8
GMRS1100-2CH OPERATIONAL MODES FUNCTION (F) CHANNEL BUTTON SELECT CTCSS SELECT POWER SELECT VOX SELECT DUAL WATCH BUTTON BEEP ROGER BEEP CALL SELECT NOTE: To differentiate between operating modes, look for HI or LO indication below the battery power level indicator when in GMRS mode.Refer to the appropriate section of this manual for de tailed operating instructions for each mode. When in standby mode, the transmit/receive indicator will flash once every 5 sec onds, indicating the unit is in the
Resumo do conteúdo contido na página número 9
volume. The display will indicate the current volume level (UL) followed by the number (0-7). As volume is increased upward, the beep sound (if enabled) also increases, and vice-versa. When the minimum and maximum volume settings are reached, a unique tone will sound. Monitor/Display Backlight Button (2) This button is used to to check activity on the current frequency before transmitting. Check activity by pressing the Monitor (M) Button longer than 2 seconds; the icon will apppear on th
Resumo do conteúdo contido na página número 10
The PTT Button can also be used as a two-way call ringer. Pressing the button twice quickly will call another party on the same channel. The transmit LED will light red for approximately 3 seconds and then go out. Up Channel/Volume Button (16) In the standby mode, pressing this button will increment the listening volume. When in function edit mode this button will be used to adjust the units settings. Down Channel/Volume Button (13) In the standby mode, pressing this button will decrement the
Resumo do conteúdo contido na página número 11
Operating Modes and Features GRMS/FRS Operation: - From GMRS/FRS standby mode, press and hold the PWR button for 2 seconds to turn on power. - Press the Function (F) button so the Channel number flashes. - Select the desired channel with the Up (16) and Down (13) Buttons. When receiving a call, the signal strength meter appears to indi- cate incoming received signal strength and the Monitor section of the Transmit/Monitor LED(9) lights green. - Press and hold the PTT button (4) to transmit, then
Resumo do conteúdo contido na página número 12
To change the channel: - From GMRS/FRS standby mode, press the Function (F) button (14) until the channel number flashes. - Press the Up Button (16) briefly to move to the next higher main chan- nel number. - Press the Down Button (13) briefly to move to the next lower main channel number. - Press the PTT or PWR button momentarily to confirm selection. CTCSS Mode (Sub-Channel) Selection The Coded Tone Controlled Squelch System (CTCSS) has 38 Sub-Frequencies. This feature allows you to utilize t
Resumo do conteúdo contido na página número 13
Transmit Power Selection Mode (GMRS Channels Only) This feature permits selection of the transmitting power level to high or low. Using low power, the unit will have a lower transmit range, but battery life will be increased. NOTE: You will find that for the majority of your needs, the low-power setting will provide adequate communications on all channels; there should seldom be any need to use high power, except in situations where you need absolute maximum range. Using low power will greatly e
Resumo do conteúdo contido na página número 14
- Momentarily press the PTT or PWR button to confirm the VOX selection. - The VOX icon will appear steady on the LCD display. VOX can be turned off by selecting oF as the setting. Dual Watch Mode This feature allows you to monitor two channels at the same time. While in dual watch mode, the unit will continuously monitor both the primary and dual watch channel. Received signals will be heard for 5 seconds, then the unit will resume scanning the two channels. Pressing the PTT button during a re
Resumo do conteúdo contido na página número 15
Button Beep (Key Tone) This feature allows the transceiver to sound a confirmation tone whenever the following keys are pressed: Monitor (M) Button, Up/Down Buttons, Func- tion Button, SCAN Button or the EMG Button. To turn the key tones on or off: - From GMRS/FRS standby mode, press the MODE Button six times until bP, the Bell ( ) icon, and On or oF flash on the LCD display. - Press the Up or Down Button to toggle the key tone feature On or Off. - Press the PTT or PWR button momentarily to co
Resumo do conteúdo contido na página número 16
- Press the Up or Down Button to preview and hear the 5 available call melodies. - Press the PTT or PWR button momentarily to confirm selection. Refer to the PTT button (4) to transmit ring signal. Channel Scan Operation This feature allows you to monitor all channels automatically for valid signals. While scanning, you can transmit and receive. When a signal is received, the scan is interrupted and will return to scan mode approxi- mately 5 seconds after reception is terminated. NOTE: While
Resumo do conteúdo contido na página número 17
Key Lock Selection Mode This feature prevents accidental channel change to the preferred settings of the unit. The Key Lock function temporarily disables the Up, Down and Function (F) Buttons. To access the Key Lock selection menu: - From FRS standby mode, press and hold the Scan Button for over 2 seconds to Lock the Key function; the ( ) icon appears on the display. - The PTT and Monitor Buttons are not effected. - To unlock the Key function, press and hold the SCAN button for at least 2 s
Resumo do conteúdo contido na página número 18
To turn the Emergency Channel feature on or off: - Press and release the EMG Button; EMG appears on the display together with a Channel 20 indication. - When the transceiver is set to Emergency Channel 20, The trans- ceiver transmits and receives on a special frequency (CH20: 462.6750 MHz). - To turn off the Emergency Channel feature, press and release the EMG Button Battery Alert When the battery icon ( ) blinks on the LCD panel, recharge unit or install fresh batteries. If the batteries
Resumo do conteúdo contido na página número 19
Warning Do not operate the transceiver unless you are licensed to do so. Remove the batteries from the transceiver if it is not expected to be used for long periods. This will eliminate the possibility of chemicals leaking from the batteries and corroding the transceiver. Avoid exposing the transceiver to water or extremes of temperature. Do not use this device in or near a mining facility, which uses remotely triggered explosives or in areas labeled Blasting Area. Premature or accid
Resumo do conteúdo contido na página número 20
Troubleshooting Problem Possible cause Correction No transmission Weak batteries Charge or replace batteries while pressing Incorrect battery polarity Install the batteries the PTT Button following the directions in paragraph Installing the Batteries. Weak or no Weak batteries Charge or replace batteries signal received Channel and privacy Adjust the transceivers code not set the same settings to match those as target transceiver settings of the target transceiver Volume level too low Increase
