Manual do usuário Metra Electronics 95-7326

Resumo do conteúdo contido na página número 1

INSTALLATION INSTRUCTIONS FOR PART 95-7326
APPLICATIONS
Hyundai Elantra 2007-2010
(US Model Only)
(Non Radio Delete)
(Non Touring Model)
95-7326
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Double DIN Trim Plate B) Double DIN Brackets
A
B
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION

Resumo do conteúdo contido na página número 2

95-7326 TABLE OF CONTENTS Dash Disassembly - Hyundai Elantra 2007-2010 .... ........ ....... ........ ........ .....1 Kit Assembly - Double DIN Radio Provision ..... ........ ........ ....... ..... ... ... 2 - Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions included with the aftermarket radio.

Resumo do conteúdo contido na página número 3

2 A/C 1 3 4 95-7326 DASH DISASSEMBLY HYUNDAI ELANTRA 2007-2010 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove the panel sur- rounding the radio including the a/c vents and hazard button. (Figure A) Remove (4) Phillips screws to remove 3 radio. (Figure B) Continue to kit assembly. B 1

Resumo do conteúdo contido na página número 4

95-7326 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the bar in the factory radio trim panel. (Figure A) TIP: The smoother the cut, the better the 95-7326 will look in the dash panel. CUT OUT BAR 2 Snap the Double DIN brackets to the inside edge of the Double DIN trim CUT HERE plate. (Figure B) 3 Slide the Double DIN radio into the bracket/trim plate assembly and B secure the radio to the assembly using the

Resumo do conteúdo contido na página número 5

95-7326 KIT ASSEMBLY STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the bar in the factory radio trim panel. (Figure A) TIP: The smoother the cut, the better the 95-7326 will look in the dash panel. CUT OUT BAR 2 Snap the Double DIN brackets to the inside edge of the Double DIN trim CUT HERE plate. (Figure B) 3 Slide the stacked ISO units into the bracket/trim plate assembly and B secure the units to the assembly u

Resumo do conteúdo contido na página número 6

95-7326 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

Resumo do conteúdo contido na página número 7

95-7326 NOTES 5

Resumo do conteúdo contido na página número 8

95-7326 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 4/27/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST95-7326