Resumo do conteúdo contido na página número 1
BDL4230ET
www.philips.com/welcome
EN User manual
Cleaning and troubleshooting
Resumo do conteúdo contido na página número 2
User Manual BDL4230ET SAFETY AND TROUBLESHOOTING INFORMATION Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Read and follow these instructions when connecting and using your display: Operation: • Keep the display out of direct sunlight and away from stoves or any other heat sources. • Remove any object that could fall into venti
Resumo do conteúdo contido na página número 3
User Manual BDL4230ET Service: • The casing cover should be opened only by qualified service personnel. • If there is any need for repair or integration, please contact your local service center. • Do not leave your display under direct sunlight. If your display does not operate normally, having followed the instructions set out in this document, please contact a technician or your local service center. Read and follow these instructions when connecting and using your display: • Unplug the disp
Resumo do conteúdo contido na página número 4
User Manual BDL4230ET REGULATORY INFORMATION CE DECLARATION OF CONFORMITY MMD declares under our responsibility that the product is in conformity with the following standards • EN60950-1:2006+A11:2009 (Safety requirement of Information Technology Equipment) • EN55022:2006+A1:2007 (Radio Disturbance requirement of Information Technology Equipment) • EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment) • EN61000-3-2:2006 (Limits for Harmonic Current Emission) • E
Resumo do conteúdo contido na página número 5
User Manual BDL4230ET POLISH CENTER FOR TESTING AND CERTIFICATION NOTICE The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computers, monitors, printers and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 Amperes (A). To completely
Resumo do conteúdo contido na página número 6
User Manual BDL4230ET INFORMATION FOR UK ONLY WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A, A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place. If the mains
Resumo do conteúdo contido na página número 7
User Manual BDL4230ET ( RoHS + (Hg) (Cd) (PBB) (PBDE) (Pb) (Cr 6 ) OOO O O O XX O O O O XO O O O O XO O O O O ( ) XO O O O O O SJ/T11363-2006 X SJ/T11363-2006 ( )
Resumo do conteúdo contido na página número 8
User Manual BDL4230ET NORTH EUROPE (NORDIC COUNTRIES) INFORMATION Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ
Resumo do conteúdo contido na página número 9
User Manual BDL4230ET TABLE OF CONTENTS 1. UNPACKING AND INSTALLATION 1.1. UNPACKING 1.2. PACKAGE CONTENTS 1.3. INSTALLATION NOTES 1.4. MOUNTING THE DISPLAY 2. PARTS AND FUNCTIONS 2.1. FRONT VIEW 2.2. REAR VIEW 2.3. INPUT/OUTPUT TERMINALS 2.4. REMOTE CONTROL 2.4.1. GENERAL FUNCTIONS 2.4.2. INSERTING THE BATTERIES IN THE REMOTE CONTROL 2.4.3. OPERATING RANGE OF THE REMOTE CONTROL 3. CONNECTIONS TO EXTERNAL EQUIPME
Resumo do conteúdo contido na página número 10
User Manual BDL4230ET 7. PIXEL DEFECT POLICY 7.1. PIXELS AND SUB-PIXELS 7.2. TYPES OF PIXEL DEFECTS + DOT DEFINITION 7.3. BRIGHT DOT DEFECTS 7.4. DARK DOT DEFECTS 7.5. PROXIMITY OF PIXEL DEFECTS 7.6. PIXEL DEFECT TOLERANCES 8. CLEANING AND TROUBLESHOOTING 8.1. CLEANING 8.2. TROUBLESHOOTING 9. TECHNICAL SPECIFICATIONS
Resumo do conteúdo contido na página número 11
User Manual BDL4230ET 1. UNPACKING AND INSTALLATION 1.1. UNPACKING • This product is packed in a carton, together with the standard accessories. • Any other optional accessories will be packed separately. • Due to the size and weight of this display it is recommended for two people to move it. • The protective glass and glass substrate are installed on the front of the product. Since glass can be both broken and scratched easily, the product should be handled with care. Never place the pr
Resumo do conteúdo contido na página número 12
User Manual BDL4230ET 1.4. MOUNTING THE DISPLAY Wall mounting holes Notes: Warning: Not for use in portrait mode. Warranty will be void if installed in any orientation other than landscape. • M6 (10mm) screws (with a length 10-15mm longer than the thickness of the mounting bracket) are needed for wall mounting (not included). Tighten the screws securely (recommended torque: 470 - 635N cm) • The mounting interface should comply with the UL1678 standard in North America. The mounting means
Resumo do conteúdo contido na página número 13
User Manual BDL4230ET 2. PARTS AND FUNCTIONS 2.1. FRONT VIEW 1 1. Remote control sensor, ambient light sensor and power indicator • Receives command signals from the remote control. • Detects the ambient lighting conditions around the display. • Indicates the operating status of the unit: - lights green when the display is turned on - lights red when the display is in standby mode - blinks green when remote control signal is received - blinks red when the display enters DPMS mode - off whe
Resumo do conteúdo contido na página número 14
100 mm 100 mm User Manual BDL4230ET 2.2. REAR VIEW 100 mm 9 Dent depth: 6mm 35 mm 8 200 mm 7 210.4 mm 1 2 3 4 5 6 1. ENTER/VIDEO SOURCE button • Use this button to select the input source. • When the On Screen Display menu is active, this is also used as the SET button. 2. MENU button • Use this button to engage the On Screen Display menu. • When the On Screen Display menu is active, use this button to return to the previous menu. 3. / button • When the On Screen Display menu is active, us
Resumo do conteúdo contido na página número 15
User Manual BDL4230ET 2.3. INPUT/OUTPUT TERMINALS 17 7 12 1 2 3 4 5 6 8 9 10 11 13 14 15 16 1. AUDIO IN (AUDIO1) 9. RS232C (OUT/IN) RS232C network connection input/output for the use of Connects to the audio output of a computer. loop through function. 2. AUDIO OUT R/L 10. VIDEO IN (COMPONENT) Outputs the audio signal from the AUDIO IN Component video input (YPbPr) for connecting to the (AUDIO1/AUDIO2/AUDIO3) or HDMI jack. component output of an AV device. 3. SPEAKERS R/L 11. VIDEO IN (S-V
Resumo do conteúdo contido na página número 16
User Manual BDL4230ET 2.4. REMOTE CONTROL 2.4.1. GENERAL FUNCTIONS POWER button Press to switch on the display from standby mode. Press again to turn it to standby mode. SMART button To select smart picture mode from: • HIGHBRIGHT: for moving images such as Video • STANDARD: for images (factory setting) • sRGB: for text based images • CINEMA: for movies. • CUSTOM: create your own picture settings. This mode is automatically selected after you change the settings in the PICTURE menu. VIDE
Resumo do conteúdo contido na página número 17
User Manual BDL4230ET BRIGHTNESS button Press to open the BRIGHTNESS OSD selection, and then press the PLUS or MINUS button to adjust the value. DISPLAY button To turn on/off the setting information displayed on the upper right corner of the screen. MENU button To turn the OSD menu on/off. UP button • To move the highlight bar up to adjust the selected item when OSD menu is on. • To move the sub-picture up in “PIP” mode. DOWN button • To move the highlight bar down to adjust the selected item
Resumo do conteúdo contido na página número 18
User Manual BDL4230ET 2.4.2. INSERTING THE BATTERIES IN THE REMOTE CONTROL 1. Remove the cover on the rear of the remote control. 2. Insert two AAA size 1.5V batteries ensuring that the “+” and “-” ends of the batteries are correctly aligned. 3. Replace the cover. Note: Do not mix battery types, e.g. alkaline and manganese. 2.4.3. OPERATING RANGE OF THE REMOTE CONTROL When pressing a remote control button, point the top of the remote control towards the remote control sensor. Use the re
Resumo do conteúdo contido na página número 19
User Manual BDL4230ET 3. CONNECTIONS TO EXTERNAL EQUIPMENT 3.1. USING THE CABLE RETAINER 3.2. CONNECTING EXTERNAL EQUIPMENT (DVD/VCR/VCD) 3.2.1. USING COMPONENT VIDEO INPUT 1. Connect the green-colored (labeled as "Y") jack of the device to the green-colored "Y" jack of the display. 2. Connect the blue-colored (labeled as "Pb") jack of the device to the blue-colored "Pb" jack of the display. 3. Connect the red-colored (labeled as "Pr") jack of the device to the red-colored "Pr" jack
Resumo do conteúdo contido na página número 20
User Manual BDL4230ET 3.2.2. USING S-VIDEO INPUT 1. Connect the S-Video connector of the external device to the S-VIDEO input of the display. 2. Connect the red (R) and white (L) audio jacks of the device to the AUDIO IN (AUDIO2 or AUDIO3) jacks of the display. DVD/VCR/VCD 3.2.3. USING VIDEO INPUT 1. Connect the Video connector of the external device to the VIDEO IN input of the display. 2. Connect the red (R) and white (L) audio jacks of the device to the AUDIO IN (AUDIO2 or AUDIO3) jack
