Resumo do conteúdo contido na página número 1
Accessory Application Publications No.
AII 23268
CD CHANGER
INSTALLATION
INSIGHT
Issue Date
ATTACHMENT KIT
INSTRUCTIONS
OCT 2001
PARTS LIST 4 Clip nuts
CD Changer Attachment Kit:
P/N 08B26-S3Y-100
2 Clips
CD changer trim
4 Self-tapping screws
4 Flange nuts
Front bracket
Bus cable
2 Spacers
Rear bracket
5 Long wire ties
(4 not used)
Front base bracket
CD Changer:
P/N 08A26-1B1-100
CD changer
Rear base bracket
6 EPT sealers
4 Washer-screws, 4 x 6 mm
(Not used)
10 Cushion tapes
Adhesive seal sh
Resumo do conteúdo contido na página número 2
3. Remove the two bolts that fasten the glove box, TOOLS AND SUPPLIES REQUIRED and remove the glove box. #2 Phillips screwdriver Flat-tip screwdriver Stubby Phillips screwdriver GLOVE BOX 10 mm Combination wrench Ratchet 10 mm Socket Diagonal cutters Utility knife Tape measure Gloves Illustration of the CD Changer Installed on the Vehicle BOLTS 4. Remove the center lower cover by removing the CD CHANGER two screws, releasing the 11 clips, and (sold separately) disconnecting the connector. BUS CO
Resumo do conteúdo contido na página número 3
5. Remove the self-tapping screws that fasten the 7. Detach the clips, and pull the driver's side cowl radio, and pull the unit out toward you. Unplug the carpet down and out of the way. vehicle harness connector and the antenna lead from the rear of the radio. SELF-TAPPING SCREW CLIPS DRIVER'S SIDE COWL CARPET (Pull down and out toward you.) ANTENNA LEAD VEHICLE HARNESS 8. Remove the B-pillar lower trim panel (four CONNECTOR retaining clips). Take care not to damage the retaining clips. 6. Remo
Resumo do conteúdo contido na página número 4
9. Remove the four expansion clips that fasten the 12. Route the BUS cable above the steering shaft, floor carpet, and fold the carpet down and out of and secure it to the vehicle harness with four the way. short wire ties in the areas shown. EXPANSION SHORT CLIP WIRE TIES VEHICLE HARNESS STEERING SHAFT FUSE BOX HOOD OPENER FLOOR CARPET (Fold down.) BUS CABLE Routing the BUS Cable 10. Route one end of the BUS cable up under the 13. Route the BUS cable down alongside the fuse dashboard, and out
Resumo do conteúdo contido na página número 5
14. Continue routing the BUS cable toward the rear 18. Remove the rear side trim panel (three of the vehicle. Measure 35 mm below the door expansion clips). opening, and secure the BUS cable to the body REAR SIDE with four cushion tapes. TRIM PANEL EXPANSION CLIP SHORT 35 mm WIRE TIE WASHER-BOLT CUSHION TAPES VEHICLE HARNESS LEFT TRUNK SIDE BOARD 15. Secure the BUS cable to the vehicle harness RELAY with one short wire tie in the area shown. 19. Remove the left trunk side board by pulling out 16
Resumo do conteúdo contido na página número 6
22. Remove the three clips, and fold down the top 24. Attach one cushion tape around the lower edge portion of the middle carpet. If the vehicle you are of the hole in the inner panel; then route the BUS working on is equipped with rear speakers, cable toward the rear over the cushion tape. remove the speakers and rear speaker holders. Secure the BUS cable to the inner panel with additional cushion tape. SPEAKER HOLDER CLIP BUS CABLE CUSHION TAPE SCREW FLOOR CARPET (Turn over.) 25. Route the BUS
Resumo do conteúdo contido na página número 7
Installing the CD Changer 30. Position the front and rear brackets on the CD changer, and install four 4 x 8 mm washer- 26. Carefully unpack the CD changer. Remove the screws into each bracket. three shipping clips, and discard the shipping cover. Save the shipping clips for your customer FRONT BRACKET in the event the unit needs to be serviced. CD CHANGER SHIPPING CLIP REAR BRACKET SHIPPING COVER (Discard.) 4 x 8 mm WASHER- SCREW ADHESIVE SEAL 4 x 8 mm WASHER-SCREW 31. Using a utility knife, c
Resumo do conteúdo contido na página número 8
32. Place the CD changer trim on the CD changer, 35. Remove the vehicle harness clip from the hole in and install the four self-tapping screws. the inner panel. CLIP CD CHANGER TRIM SELF-TAPPING SCREWS CD CHANGER SELF-TAPPING CLIP NUT SCREWS 36. Slide one clip nut onto each of the four holes in 33. Remove 40 to 50 mm of the adhesive backing the inner panel. from the back of each spacer, and fold them back. Position the spacers on the CD changer 37. Apply one EPT sealer to the left taillight harn
Resumo do conteúdo contido na página número 9
38. Cut one piece of EPT sealer in half. Attach the 42. Position the CD changer on the studs extending halves to the rear clip nuts you installed in step from the front and rear base brackets, and install 36. the four flange nuts. Install the CD changer first on the front bracket, then the rear bracket. EPT SEALER FRONT BRACKET STUDS REAR EPT SEALER BRACKET (Cut in half.) STUDS CD CHANGER FLANGE NUTS 43. Reinstall the relay that was removed in step 20. REAR BASE FRONT BRACKET BASE EPT BRACKET SE
Resumo do conteúdo contido na página número 10
45. Secure the BUS cable connector to the vehicle 47. Reinstall the left trunk side board on the CD harness 135 mm away from the vehicle harness changer brackets, and install the two clips. clip with one long wire tie. Attach the BUS cable to the corner of the body panel with one cushion BASE tape in the area shown. BRACKET CD CHANGER BUS CABLE LONG WIRE TIE CD CHANGER BASE BRACKET 135 mm CLIPS LEFT TRUNK BUS CABLE CUSHION TAPE SIDE BOARD CONNECTOR Secure to the corner. 48. Reinstall the trunk b
