Resumo do conteúdo contido na página número 1
CRW4260tx
User Guide
Guide de I’utilisateur
Bedienungsanleitung
POWER
CRW-4260tx
Resumo do conteúdo contido na página número 2
COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Yamaha Systems Technology, Inc. Address: 100 Century Center Court San Jose, California 95112 Telephone: (408) 467-2330 FAX: (408) 437-8791 Type of Equipment: CD Recorder Model Name: CRW4260tx This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received inc
Resumo do conteúdo contido na página número 3
Laser Diode Properties CAUTION Material : GaAlAs Use of controls or adjustments or performance of Wavelength : 782-789 nm procedures other than those specified herein may Emission Duration : Continuous result in hazardous radiation exposure. Laser Output Power : Less than 44.6 μW* * This output is value measured at a distance 200mm from the objective lens surface on the optical pick-up block. ANSI Class : Class 1 This compact disc player is classified as a CLASS 1 LASER product. CLAS
Resumo do conteúdo contido na página número 4
Important Precautions Important Precautions Please read the following precautions before operating CRW4260tx. • Do not remove the CRW4260tx’s top cover. This device uses semiconductor laser. Refer all servicing to qualified personnel. • Do not attempt to touch the inside of the CRW4260tx. Electricity may have been built up even after you turn off the power. • CRW4260tx is a sophisticated electronic device. Handle it with care. • If the fuse blows, CRW4260tx should be checked by a qual
Resumo do conteúdo contido na página número 5
Installation Precautions Installation Precautions • Install CRW4260tx on a level surface. • Do not install CRW4260tx near water, in direct sunlight, close to heating units, or in areas subject to high or low temperature extremes, excessive dust, vibration, or severe shocks. • Do not expose CRW4260tx to extremes of humidity. • The ambient temperature where CRW4260tx is installed should be between 5 C and 40 C (41 F–104 F). • Using CRW4260tx close to a television or radio ma
Resumo do conteúdo contido na página número 6
Operating Precautions Operating Precautions • Do not subject CRW4260tx to impact or shock when in use. This may impair recording or playback. • Do not place heavy objects on CRW4260tx. • Avoid moving CRW4260tx from cold to warm places, and avoid sudden room temperature rises, as condensation that could cause CRW4260tx to malfunction may occur. If condensation does occur, wait at least one hour before operating CRW4260tx. • Do not let liquid or other foreign objects enter CRW4260tx. • To
Resumo do conteúdo contido na página número 7
Preventing Premature Disc Failure Preventing Premature Disc Failure The NUMBER ONE cause of premature disc failure with recordable CDs is contamination of the recording surface before recording is completed. To minimize disc failure, use the following disc-handling guidelines: • Keep the disc tray and disc as clean and dust-free as humanly possible during the record process. DO NOT touch the recording surface, and do not expose the disc tray and disc to dust or dirt. • DO NOT BLOW ON
Resumo do conteúdo contido na página número 8
Table of Contents Table of Contents Introduction ............................................................................. 1 Accessories .................................................................... 1 CRW4260tx Features .................................................... 2 Orange Book Compatible Recording ............................ 3 Chapter 1 - System Configuration ..................................... 4 Computer ..................................................
Resumo do conteúdo contido na página número 9
User Guide Guide de l’utilisateur Bedienungsanleitung YAMAHA CRW4260tx W CR -4260tx POWER Introduction Introduction Thank you for purchasing a Yamaha CRW4260tx drive. Please read this manual before using the drive in order to make the best use of the superior CRW4260tx functions. After reading, please retain this manual for future reference. Accessories The package should contain the following items along with the drive. Check to see if you have all these items. 1 Power cable x 1
Resumo do conteúdo contido na página número 10
Introduction CRW4260tx Features n 2xS Recording (Rewritable) - 4xS Recording (Recordable) - 6xS Reading The CRW4260tx is able to write (overwrite) CD-RW discs at double speed, and is able to write CD-R discs at quad speed, double speed, or normal speed. For both types of media, this drive is able to read at 6X speed, quad speed, double speed, or normal speed, and any of these modes can be selected as desired. n Compatible with Seven Different Formats The CRW4260tx can bot
Resumo do conteúdo contido na página número 11
Introduction Orange Book Compatible Recording Track at Once In this mode, data can be recorded to disc one track at a time. Discs recorded in this mode cannot be played in CD players or CD-ROM drives other than a CD-RW or CD-R drive until the session is closed. Multisession In this mode, data can be recorded to disc in stages (one session at a time). Additional data can be written later. Disc at Once In this mode, data can be recorded to an entire disc in one pass. It is not poss
Resumo do conteúdo contido na página número 12
Chapter 1 - System Configuration Chapter 1 - System Configuration In order to use the CRW4260tx, you will require the following. Computer The following operating environment is required: • An IBM/AT compatible computer with a 100 MHz or faster Pentium CPU (in order to write at 4x speed), or a 100 MHz or faster 486 CPU (in order to write at 2x speed) • A vacant slot in which to install a SCSI card or a pre-installed SCSI card • Windows 3.1, Windows 95, Windows NT4.0 or Higher • Suf
Resumo do conteúdo contido na página número 13
Chapter 1 - System Configuration Discs On the CRW4260tx, you can use conventional CD-RW and CD-R discs that conform to the Recordable Compact Disc Systems Part 2 and Part 3 (Orange Book). Yamaha recommends the following Yamaha CD-RW and CD-R discs: CD-RW Discs > CRWM74R (f 120mm, 74 minutes) CD-R Discs > CDM12Y63 (f 120mm, 63 minutes) > CDM12Y74 (f 120mm, 74 minutes) > CDM12Y74M (f 120mm, 74 minutes) > CDM12Y74T (f 120mm, 74 minutes) Read-only Discs You can use discs with
Resumo do conteúdo contido na página número 14
Chapter 2 - Touring Around CRW4260tx Chapter 2 - Touring Around CRW4260tx Rear Panel 5 SCSI-1 SCSI-2 AC I N LINE OUT CDR ID R L TERMINATOR 1 OFF ON 1 2 3 4 1 AC IN Connect the included power cable here. 2 CDR ID Use this switch to set a unique SCSI ID number for the CRW4260tx. 3 TERMINATOR This switch is used to set termination. Refer to the terminator setting section for details. 4 LINE OUT (L, R) These jacks are used to output audio to the amplifier. 5 SCSI-1, SCSI-2 Thes
Resumo do conteúdo contido na página número 15
Chapter 2 - Touring Around CRW4260tx Front Panel 1 6 7 8 POWER CRW4260tx 2 3 4 5 1 Disc tray The disc is inserted and ejected here. Pressing the eject button will open the tray. 2 Headphone jack This stereo mini jack allows you to connect headphones and listen to audio. 3 Headphone volume control This control adjusts the volume level of the headphone output. Rotating the control clockwise will increase the volume level. 4 ON/DISC LED This indicator lights up in orange when the CRW4260tx
Resumo do conteúdo contido na página número 16
CDR ID – 1 + Chapter 3 - Installing the Yamaha CRW4260tx Drive Chapter 3 - Installing the Yamaha CRW4260tx Drive CRW4260tx drive settings ' SCSI ID settings The SCSI ID number is used so that the computer will recognize a connected SCSI device. You can assign 0 through 7 as the SCSI ID number. Usually, “7” is reserved for the SCSI card ID number, and “0” is reserved for the first SCSI device in the chain. Use a number between 1 and 6 for the CRW4260tx. Use the switch on the rear panel to set
Resumo do conteúdo contido na página número 17
Chapter 3 - Installing the Yamaha CRW4260tx Drive Cable Connection Power cable Insert the power cable securely to the “AC IN” connector on the rear panel. SCSI-1 SCSI-2 AC I N LINE OUT CDR ID R L TERMINATOR 1 OFF ON SCSI cable Connect the SCSI cable to either of the CRW4260tx rear panel SCSI connectors (1) or (2), and connect the other end of the SCSI cable to the host computer. The CRW4260tx is not supplied with a SCSI cable. You will need to obtain one that will fit the drive and the hos
Resumo do conteúdo contido na página número 18
Chapter 4 - Operation Chapter 4 - Operation Loading a Disc 1. Press the eject button to open the tray. 2. Carefully place the disc, label-side up, on the disc tray. 3. Press the disc tray softly or press the eject button again to close the disc tray. Important: Take great care when handling CD-ROM discs. They are more sensi- tive to damage than audio CDs, and the slightest scratch can render a disc useless. Do not expose discs to dust, dirt, heat, or moisture. 10 POWER CDR-400cx
Resumo do conteúdo contido na página número 19
Chapter 4 - Operation Ejecting the Disc If the CRW4260tx is powered on: Press the eject button to eject the disc. Note: You cannot eject the disc if the SCSI command prohibits the eject operation while the CRW4260tx is reading data. Caution: Be sure to remove the disc after it is completely ejected. (Trying to remove the disc before it is completely ejected may cause the drive to malfunction.) Press the eject button If the CRW4260tx is not powered on: Pressing the eject button will not eject
Resumo do conteúdo contido na página número 20
Chapter 4 - Operation Manual Eject (emergency use) Here we explain how to eject the disc when it cannot be ejected in the normal way; for example, the power is shut off inadvertently or the loading mechanism fails. This technique should be used only as a last resort. Frequent use may lead to malfunction. You’ll need a pin-like object of 2 mm or less in diameter to do this. A straightened paper clip makes an ideal tool. 1. Insert the pin-like tool into the manual eject hole and push gently.
