Resumo do conteúdo contido na página número 1
EF5001U-B Pellet Heater
Installation & Operating Instructions
Please read this entire manual before installation. Save these instructions.
GENERAL INFORMATION
Installation and repair should be done by a qualified service
person. The heater should be inspected before use and at
least annually by a professional service person. More
frequent cleaning may be required due to fuel quality,
excessive lint from carpeting, bedding material, etc. It is
imperative that control compartments, burners and cir
Resumo do conteúdo contido na página número 2
Figure 2 WARNING: Installation of a Mobile Home Attachment Kit P/N 10412 and outside combustion air is mandatory in Figure 1 -Overall Dimensions mobile or modular home installations although it may also be used in all residential applications. An outside air inlet MUST be provided for combustion OUTSIDE COMBUSTION AIR IS MANDATORY IN and ventilation air. The air inlet must remain unrestricted MOBILE OR MODULAR HOME INSTALLATIONS. while unit is in use. Outside air connection is located in the r
Resumo do conteúdo contido na página número 3
Figure 3 c. 2 ft. minimum to an adjacent building and 7 ft. minimum above grade when located adjacent to public walkways. Figure 5 Figure 4 Figure 6 3
Resumo do conteúdo contido na página número 4
IMPORTANT - Any electrical work performed on the UNIT INSTALLATION EASYFIRE Heater should be done by qualified personnel. Route the power supply cord so that it does not touch any of the exterior components of the heater. 1. W hen exiting through the wall with your type L Pellet vent pipe, you may go straight out through a wall thimble. You must connect a pellet vent tee at this point and extend the vent pipe at least 3' (three feet) vertically outside to provide good draft and allow the gase
Resumo do conteúdo contido na página número 5
stove operates based on the EasyFire digital control system requirements. If the house AC power should quit, the AutoLite system will not be available however, with the optional battery attached the stove can be manually lit and operate on battery power for several days (depending on battery size). START-UP AND OPERATION Warning: This stove incorporates a hopper lid safety switch. The feed system will remain in-operable when the door is open. Figure 9 Door handle assembly Priming the feed syst
Resumo do conteúdo contido na página número 6
B. In the LOW position, the EASYFIRE will be feeding Feed Trim Adjustment approximately 1 to 1½ lbs. of pellets per hour and the flame will fluctuate between 1" and 6" in height. Underneath the control button you will find a small round button that will turn forward and reverse. This button can C. In the MEDIUM position the EASYFIRE will be feeding adjust the feed motor in the LOW operating position. By approximately three (3) pounds of pellets per hour and turning the button clockwise you can
Resumo do conteúdo contido na página número 7
heat exchanger hot before turning it to "LOW ". You will are disposed of by burial in soil or otherwise locally need to burn the heater for a few hours before deciding dispersed, they should be retained in the closed container which setting is best for your particular needs. until all cinders have been thoroughly cooled. NOTE: CAUTION MUST BE TAKEN WHEN OPTIONAL 12V HOOK-UP & OPERATION INSTALLING BURN POT OR OPERATING DOOR NOT TO DAMAGE CERAMIC GLASS. DO NOT ATTEMPT TO 1. The EASYFIRE 12V back
Resumo do conteúdo contido na página número 8
4. Clearance to combustibles may only be reduced by a. Open door and remove clean out slide cover. To means approved by the regulatory authority. remove, simply slide up and out from retaining angle bracket (Figure 10). Clean one side at a time. With one slide cover removed, leave door open and turn 5. Store pellet fuels in a dry area away from unit. Do not control knob to the "CLEAN" position. Let heater run store fuels within the space heater installation until ash in fire pot area is vacuumed
Resumo do conteúdo contido na página número 9
existing flue must be installed with a tee connector frame. Apply sealer to mating edge of glass and frame. Allow two hours dry time before installing door onto (Figure 3,4,& 5) to allow access to clean the ash from the pellet vent pipe. heater. Note: Replace with Pyro-Ceramic Glass only. Refer to parts list for specifications. TROUBLE-SHOOTING The following scenarios are provided in order to help you locate a difficulty if the heater performs in a manner which would seem to indicate a malfunct
Resumo do conteúdo contido na página número 10
under the control knob came on. This light is the Hi 10. Problem: Feed system jammed. Temp/Flue Indicator Light. Solution: This condition is caused by fuel contaminated Solution: The Hi-Temp/Flue Indicator light indicates with hard materials such as rocks or metal objects. To that fly ash has built up in the exhaust system and/or correct this remove all pellets from hopper. Unplug there is a restriction in the exhaust/flue system. Check heater from any power source (12V & 110V). Remove the pipe
Resumo do conteúdo contido na página número 11
` ITEM No. PART NUMBER DESCRIPTION 1 110499 DOOR FRONT GLASS (Ceramic glass 13 1/2"x11 3/4"x5mm) 2 100125 DOOR FIBER ROPE GASKET 3 10401 12VDC - 30 AMP SLA BATTERY 4 202228 BATTERY DRAWER 5 300522 ASH DRAWER 6 300513 FIRE POT - 5001 AL 7 120117 AUTOLITE IGNITOR 8 110451 ASH DUMP KNOB 9 110058 HANDLE ASSEMBLY 10 120114 DOOR CATCH 11 300106 AUTOLITE SWITCH MOUNTING PLATE 12 110049 TRANSFORMER 13 120116 AUTOLITE WIRING HARNESS 14 120114 V2- MAIN CONTROL BOARD 15 120118
