Resumo do conteúdo contido na página número 1
1” SDS ROTARY HAMMER
Model 47606
SET up AnD OpERATing inSTRucTiOnS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THiS MAnuAl.
© ®
Cop
Resumo do conteúdo contido na página número 2
Specifications Chuck Capacity 1 Inch Power 120 V, 60 Hz, 1.13 HP, 850 Watts Amperage 6.8 Peak Amps, 4.6 Working Amps RPM 900 Blows per minute 3,200 Accessories: Break Point (Bull) Bit, Flat Head Chisel, Depth Rod, Lubricant, Masonry Drill Bits (10mm, 9/16”, 7/8”), Extra Brushes, Blowmold Case Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual
Resumo do conteúdo contido na página número 3
damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times. 10. Disconnect power. Unplug tool when not in use. 11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are removed from the tool or machine work surface before plugging it in. 12. Avoid unintentional starting. Be sure the switch is in the Off position when not in use and before plugging in. Do not carry any tool with your finger
Resumo do conteúdo contido na página número 4
- Lead from lead-based paints - Crystalline silica from bricks and cement or other masonry products - Arsenic and chromium from chemically treated lumber Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code § 25249
Resumo do conteúdo contido na página número 5
Assembly Refer to Figure 1. 1. Fit the Handle band (508) over the front of the housing above the Bit Sleeve and screw the Handle (506) clockwise to secure. At this point do not fully tighten. 2. Rotate the Handle (506) around the tool until it rests on a flat spot on the housing, on the side you prefer. note: The Drill Stop (504) is used as a guide when doing repetitive drilling (not chiseling) at the same depth. 3. With the Handle (505) still loose, insert the Drill Stop (504) into the h
Resumo do conteúdo contido na página número 6
inserting and removing bits. 1. Make sure the Rotary Hammer is not plugged in. 2. To insert a bit, pull back and retract the Bit Sleeve (see FIGURE 2) and insert the bit. Slide the two notches on the bit into the notched receptacle and then release the Bit Sleeve. Put on gloves and then tug on the bit forcefully, making sure it is in the Bit Sleeve firmly. 3. When removing a bit, make sure the bit has had a chance to cool. Wear gloves and grip the bit with one hand, and pull back on the Bit
Resumo do conteúdo contido na página número 7
Operation note: Make sure unit is not plugged in. Dust Dust F Figu iguRE 4 RE 4 note: If you wish, you may attach a Dust cap for overhead Cap Cap drilling applications. To do so, after you install a bit, Curved end Curved end before you tighten the Bit Sleeve, slide the Dust cap of Drill Stop of Drill Stop over the bit and adjust the Drill Stop so that the curve on the end of the Drill Stop secures the Dust c ap. Tighten the Handle. See FIGURE 4. note: Do not plug in the Rotary Hammer
Resumo do conteúdo contido na página número 8
Troubleshooting and Maintenance note: Other than changing or cleaning the carbon brushes, all internal repairs should be done by a qualified service technician. problem cause Action Motor doesn’t rotate when switched 1. Disrupted power 1. Check Power Supply on. 2. Poor switch contact 2. Repair switch 3. Armature or field coil burnt 3. Change coil 4. Broken Stator Coil 4. Replace Stator coil 5. Worn carbon brushes 5. Replace carbon brushes Abnormal motor noise, rotates slowly, Overload due to e
Resumo do conteúdo contido na página número 9
parts list part Description part Description part Description 1 O-ring 35 Spring 302 Switch Handle 2 Steel Ball 36 Label 71* Air Baffle 3 Cylinder 37 Small Cone Gear 72* Stator 4 Flat Pin 38 Oil Seal 74* Motor Casing 5 Striker 39 Bearing 75* Bolt 6 O-ring 40 Washer 76* Bottom Cap 706 Spring 41 Pull Board 77* Tap Bolt 7 Cone Gear 42 Clutch Washer 78 Tap Bolt 7D Steel Retaining Ring 43 Second Gear 79 Handle Cap 511 Oil Bearing 44 Dish Form Spring 80 Handle Buff 8 Piston 45 Specialty Nut 85 Capacit
Resumo do conteúdo contido na página número 10
Assembly Drawing 701 702 1 2 703 3 4 704 504 503 501 705 5 6 706 509 7 508 7D 507 18 506 511 19 20 505 6 11 21 8 9 22 10 12 23 14 13 24 16 25 27 26 28 29 30 47 36 31 48 32 37 33 34 49 38 30 35 39 50 40 57 51 41 52 42 58 53 43 54 42 60 55 41 56 44 45 61 46 89 71 90 19 91 72 85 86 64 73 65 66 92 78 79 93 66 74 19 67 68 98 75 80 69 70 76 77 97 77 SKU 47606 For technical questions, please call 1-800-444-3353. Page 10
Resumo do conteúdo contido na página número 11
plEASE READ THE FOllOWing cAREFull Y THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UND
