Resumo do conteúdo contido na página número 10
LES RAYONS DE L’ARC peuvent pro- LES ACCUMULATIONS DE GAZ ris- voquer des brûlures dans les yeux et quent de provoquer des blessures ou sur la peau. même la mort. Le rayonnement de l’arc du procédé de soudage Fermer l’alimentation du gaz protecteur en cas de génère des rayons visibles et invisibles intenses non utilisation. (ultraviolets et infrarouges) susceptibles de provoquer des brûlures dans les yeux et sur la peau. Des étincelles sont projetées Veiller toujours à bien aérer les espaces
Resumo do conteúdo contido na página número 11
1-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance Risque D’INCENDIE OU DES ORGANES MOBILES peuvent D’EXPLOSION. provoquer des blessures. Ne pas placer l’appareil sur, au-dessus ou à proxi- Rester à l’écart des organes mobiles comme le mité de surfaces infllammables. ventilateur. Maintenir fermés et fixement en place les portes, Ne pas installer l’appareil à proximité de produits inflammables panneaux, recouvrements et dispositifs de Ne pa
Resumo do conteúdo contido na página número 12
1-4. Principales normes de sécurité Safety in Welding and Cutting, norme ANSI Z49.1, de l’American Wel- Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1, ding Society, 550 N.W. Lejeune Rd, Miami FL 33126 de la Compressed Gas Association, 1235 Jefferson Davis Highway, Suite 501, Arlington, VA 22202. Safety and Health Sandards, OSHA 29 CFR 1910, du Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. Règles de sécurité en soudage, coupage et procédés conne
Resumo do conteúdo contido na página número 13
SECTION 2 – DEFINITIONS 2-1. Manufacturer’s Warning Label Definitions Warning! Watch Out! There are possible hazards as shown by the symbols. 1 Electric shock from welding electrode or wiring can kill. 1.1 Wear dry insulating gloves. Do not touch electrode with bare hand. Do not wear wet or damaged gloves. 1.2 Protect yourself from electric shock by insulating yourself from work and ground. 1.3 Disconnect input plug or power before working on machine. 2 Breathing welding fumes can be hazardous t
Resumo do conteúdo contido na página número 14
1 Warning! Watch Out! There are possible hazards as shown by the symbols. 2 Electric shock from wiring can kill. 1 34 5 6 2 3 Disconnect input plug or power before working on machine. 4 Hazardous voltage remains on input capacitors after power is turned off. Do not V touch fully charged capacitors. V 5 Always wait 60 seconds after > 60 s V power is turned off before working on unit, OR 6 Check input capacitor voltage, and be sure it is near 0 before touching any parts. S-185 836 7 When power is
Resumo do conteúdo contido na página número 15
2-2. Manufacturer’s Rating Labels OM-193 084 Page 11
Resumo do conteúdo contido na página número 16
2-3. Symbols And Definitions Alternating Amperage Panel Voltage Current (AC) A V Output Circuit Breaker Remote On Gas Tungsten Arc Off Negative Voltage Input Welding Direct Current Protective Earth Positive Inductance (DC) (Ground) Constant Current Constant Voltage Foot Control Line Connection Three Phase Static Frequency Con- Shielded Metal Arc Gas Metal Arc Arc Force verter- Welding (SMAW) Welding (GMAW) Transformer- Rectifier Rated No Load Conventional Primary Voltage Duty Cycle U Voltage (Av
Resumo do conteúdo contido na página número 17
SECTION 3 – INSTALLATION 3-1. Specifications Voltage Amperes Input Range Maximum at Rated Load Rated Welding Amperage Open-Circuit IP Rating (CC/CV Output 50/60 Hz Output Output Range Range Models Voltage DC 460 V KVA KW Only) 300 A @ 18.5 14.9 11.4 32 Volts DC, 10 – 35 5 – 400 90 23 (0.15*) (0.09*) (0.04*) 60% Duty Cycle *While idling 3-2. Duty Cycle And Overheating Duty Cycle is percentage of 10 min- utes that unit can weld at rated load without overheating. If unit overheats, output stops, a
Resumo do conteúdo contido na página número 18
3-3. Volt-Ampere Curves Volt-ampere curves show minimum and maximum voltage and amper- age output capabilities of unit. Curves of other settings fall be- tween curves shown. A. CC Mode B. CV Mode ARC CONTROL va_curve1 4/95 – SA-178 652 / SA-178 653 OM-193 084 Page 14
Resumo do conteúdo contido na página número 19
3-4. Selecting A Location 24 in (610 mm) Dimensions And Weight 87 lb (39.5 kg) 17 in (432 mm) 12-1/2 in (318 mm) Movement 1 Lifting Handles Do not move or operate unit 1 Use handles to lift unit. where it could tip. 2 Hand Cart Use cart or similar device to move unit. 1 3 Plate Label 2 Use label to determine input power needs. 4 Line Disconnect Device Locate unit near correct input power supply. Special installation may be required where gasoline or volatile liquids are present – see NEC Art
Resumo do conteúdo contido na página número 20
3-5. Weld Output Terminals And Selecting Cable Sizes ARC WELDING can cause Electromagnetic Interference. To reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor. Locate welding operation 100 meters from any sensitive electronic equipment. Be sure this welding machine is installed and grounded according to this manual. If interference still occurs, the user must take extra measures such as moving the welding machine, using shiel
Resumo do conteúdo contido na página número 1
OM-193 084E
March 2002
Processes
Multiprocess Welding
Description
Arc Welding Power Source
XMT 304
(460 Volt Models)
CC/CV and CC Models
Visit our website at
www.MillerWelds.com
Resumo do conteúdo contido na página número 2
From Miller to You Thank you and congratulations on choosing Miller. Now you can get the job done and get it done right. We know you don’t have time to do it any other way. That’s why when Niels Miller first started building arc welders in 1929, he made sure his products offered long-lasting value and superior quality. Like you, his customers couldn’t afford anything less. Miller products had to be more than the best they could be. They had to be the best you could buy. Today, the people that bu
Resumo do conteúdo contido na página número 3
TABLE OF CONTENTS SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-3. Additional Symbols For Installation, Operation, And Maintenance . . . . . . .
Resumo do conteúdo contido na página número 4
Declaration of Conformity For European Community (CE) Products Manufacturer’s Name: Miller Electric Mfg. Co. Manufacturer’s Address: 1635 W. Spencer Street Appleton, WI 54914 USA Declares that the product: XMT 304 conforms to the following Directives and Standards: Directives Electromagnetic compatibility Directives: 89/336/EEC, 92/31/EEC Low Voltage Directive: 73/23/EEC Machinery Directives: 89/392/EEC, 91/368/EEC, 93/C 133/04, 93/68/EEC Standards Electromagnetic compatibility (EMC) Product st
Resumo do conteúdo contido na página número 5
SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING som _nd_4/98 1-1. Symbol Usage Means Warning! Watch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols. This group of symbols means Warning! Watch Out! possible Marks a special safety message. ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessary actions Means “Note”; not safety related. to avoid the hazards. 1-2. Arc Welding
Resumo do conteúdo contido na página número 6
ARC RAYS can burn eyes and skin. BUILDUP OF GAS can injure or kill. Shut off shielding gas supply when not in use. Arc rays from the welding process produce intense visible and invisible (ultraviolet and infrared) rays Always ventilate confined spaces or use that can burn eyes and skin. Sparks fly off from the approved air-supplied respirator. weld. Wear a welding helmet fitted with a proper shade of filter to protect your face and eyes when welding or watching (see ANSI Z49.1 and Z87.1 li
Resumo do conteúdo contido na página número 7
1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. MOVING PARTS can cause injury. Do not install or place unit on, over, or near Keep away from moving parts such as fans. combustible surfaces. Keep all doors, panels, covers, and guards Do not install unit near flammables. closed and securely in place. Do not overload building wiring – be sure power supply system is properly sized, rated, and protected to handle this unit. FALLING UNIT can cau
Resumo do conteúdo contido na página número 8
1-5. EMF Information Considerations About Welding And The Effects Of Low Frequency 1. Keep cables close together by twisting or taping them. Electric And Magnetic Fields 2. Arrange cables to one side and away from the operator. Welding current, as it flows through welding cables, will cause electro- magnetic fields. There has been and still is some concern about such fields. However, after examining more than 500 studies spanning 17 3. Do not coil or drape cables around your body. years of resea
Resumo do conteúdo contido na página número 9
SECTION 1 – CONSIGNES DE SECURITE – LIRE AVANT UTILISATION som _nd_fre 4/98 1-1. Signification des symboles Signifie Mise en garde ! Soyez vigilant ! Cette procédure présente des risques de danger ! Ceux-ci sont identifiés par des symboles adjacents aux directives. Ce groupe de symboles signifie Mise en garde ! Soyez vigilant ! Il y a des Identifie un message de sécurité particulier. risques de danger reliés aux CHOCS ÉLECTRIQUES, aux PIÈCES EN MOUVEMENT et aux PIÈCES CHAUDES. Reportez-vous au
