Resumo do conteúdo contido na página número 1
SCRUBTEC 770 S SCRUBTEC 770 S SCRUBTEC 770 S SCRUBTEC 770 S SCRUBTEC 770 S
SCRUBTEC 770 L SCRUBTEC 770 L SCRUBTEC 770 L SCRUBTEC 770 L SCRUBTEC 770 L
SCRUBTEC 784 S SCRUBTEC 784 S
SCRUBTEC 784 S SCRUBTEC 784 S SCRUBTEC 784 S
Operator's
SCRUBTEC 784 L SCRUBTEC 784 L SCRUBTEC 784 L
SCRUBTEC 784 L SCRUBTEC 784 L
SCRUBTEC 795 S SCRUBTEC 795 S SCRUBTEC 795 S
SCRUBTEC 795 S SCRUBTEC 795 S
Manual
SCRUBTEC 795 L SCRUBTEC 795 L SCRUBTEC 795 L SCRUBTEC 795 L SCRUBTEC 795 L
U.S. Patent No. 6,760,947; No. 6
Resumo do conteúdo contido na página número 2
Table of Contents Operator Safety Instructions ............................................................................................................................. 3 Introduction ....................................................................................................................................................... 4 Machine Specifications .................................................................................................................................... 5
Resumo do conteúdo contido na página número 3
OPERATOR SAFETY INSTRUCTIONS DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner's Manual and on your machine. WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other personnel; property damage could occur as well. Read and observe all WARNING statements found in your Owner's Manual and on your machine. CAUTION: Failure to read and observ
Resumo do conteúdo contido na página número 4
WARNING: Any alterations or modifications of this machine could result in damage to the machine or injury to the operator or other bystanders. Alterations or modifications not authorized by the manufacturer voids any and all warranties and liabilities. WARNING: Electrical components of this machine can "short-out" if exposed to water or moisture. Keep the electrical components of the machine dry. Wipe the machine down after each use. For storage, keep the machine in a dry building. WARNING:
Resumo do conteúdo contido na página número 5
Machine Specifications SPECIFICATIONS: Model Scrubtec 795 S Scrubtec 784 S Scrubtec 770 S Motor, Vac 1 HP (.74kw) three 1HP (.74kw) three 1HP (.74kw) three stage tangential stage tagential stage tagential discharge discharge discharge Power Supply 36 volt (6-6V batteries) 36 volt (6-6V batteries) 36 volt (6-6V batteries) 250AH, 330AH 250AH, 330AH 250AH, 330AH Solution Tank 30 gallon (114 liter) 30 gallon (114 liter) 30 gallon (114 liter) Recovery Tank 30 gallon (114 liter) 30 gallon (114 liter)
Resumo do conteúdo contido na página número 6
Machine Specifications SPECIFICATIONS: Model Scrubtec 795 L Scrubtec 784 L Scrubtec 770 L Motor, Vac 1 HP (.74kw) three 1HP (.74kw) three 1HP (.74kw) three stage tangential stage tagential stage tagential discharge discharge discharge Power Supply 36 volt (6-6V batteries) 36 volt (6-6V batteries) 36 volt (6-6V batteries) 250AH, 330AH 250AH, 330AH 250AH, 330AH Solution Tank 30 gallon (114 liter) 30 gallon (114 liter) 30 gallon (114 liter) Recovery Tank 30 gallon (114 liter) 30 gallon (114 liter)
Resumo do conteúdo contido na página número 7
PROCEDURES FOR TRANSPORTING How To Put The Machine In A Van Or Truck WARNING: The machine is heavy. Make sure you use two able persons to assist the machine in climbing the ramp. 1. Make sure the loading ramp is at least 2.4m long, and strong enough to support the machine. 2. Make sure the ramp is clean and dry. 3. Put the ramp in position. 4. Remove squeegee assembly, brush housings, & brushes or pad drivers before loading. 5. Turn key switch "ON". 6. Align the machine on a level surface 3.1m
Resumo do conteúdo contido na página número 8
SYMBOLS USED ON SCRUBTEC 770, 784, 795 SYMBOLS USED ON SCRUBTEC 770 S, 784 S & 795 S SCRUBTEC 770 L, 784 L, 795 L Traverse Speed Control Hazard Alert Symbol On/Off Key Switch Power SYMBOLS USED ON SYMBOLS USED ON SCRUBTEC 770 L, 784 L & 795 L SCRUBTEC 770 S, 784 S & 795 S Solution Squeegee Control Up/Down Additional Brush Brush Up/Down Pressure Hour Meter Switch Brush Up/Down Charge/Battery Solution Control Meter Charge Indicator One Touch Switch Page -8- CLARKE TECHNOLOGY Ope
Resumo do conteúdo contido na página número 9
SYMBOLS USED ON SCRUBTEC 770, 784, 795 WARNING WARNING READ OPERATOR'S MANUAL BEFORE OPERATING THIS MACHINE READ OPERATOR'S MANUAL BEFORE EXPLOSIVE GASES, OPERATING THIS CAN CAUSE SEVERE MACHINE INJURY, DEATH OR DAMAGE RISK OF FIRE TRANSFORMER. • Use only • Keep flammable commercially materials away from available floor batteries. Charge in cleaners and a cool well ventilated waxes intended area. for machine operation. BATTERIES • Do not use CONTAIN SULFURIC flammable ACID. CAN CAUSE materi
Resumo do conteúdo contido na página número 10
MACHINE CONTROL PANEL SRUBTEC 770 S, 784 S & 795 S Key Switch (See Figure #1, Item "A") The key switch turns "ON" the power to the control panel. "0" is "OFF" and "I" is "ON". Traverse Speed Switch (See Figure #1, Item "B") The speed control varies from low to high speed. To increase the speed, turn the knob to the right. To decrease the speed, turn the knob to the left. Brush Up/Down Switch (See Figure #1, Item "C") The brush switch has two positions: "Up" positions the brushes up; "Dow
Resumo do conteúdo contido na página número 11
MACHINE CONTROL PANEL SRUBTEC 770 S, 784 S & 795 S B G F F C D E A L M K J I H N Figure #1 CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795 - 11 - SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795
Resumo do conteúdo contido na página número 12
MACHINE CONTROL PANEL SRUBTEC 770 L, 784 L & 795 L Key Switch (See Figure #2 Item "A") The key switch turns "ON" the power to the control panel. "O" is "OFF" and "I" is "ON". Traverse Speed Switch (See Figure #2, Item "B") The speed control varies from low to high speed. To increase the speed, turn the knob to the right. To decrease the speed, turn the knob to the left. Squeegee Up/Down Switch (See Figure #2, Item "C") The squeegee switch is used to raise and lower the squeegee and to tur
Resumo do conteúdo contido na página número 13
MACHINE CONTROL PANEL SRUBTEC 770 L, 784 L & 795 L Circuit Breakers (See Figure #2, Item "K", "L", "M") The circuit breaker reset buttons are located on the control panel. The breakers are located as follows: Item "L" and "M" - Brush Motors (35A); Item N - Key Switch (5A). If a circuit breaker trips, determine which motor is not operating and turn the key switch "OFF". Wait five minutes and push the reset button back in. Turn the key switch "ON", and try again. An authorized service person
Resumo do conteúdo contido na página número 14
Display Screens For SCRUBTEC 770 L, 784 L, 795 L Position arrow indicating current position of squeegee (up or down) 3 Indicators are on all the time showing current settings. SCREEN 1 Water “droplets” off when solution is off and they are flashing when solution is on. “Battery” blinks when low voltage occurs. Arrows indicating vacuum status. Screens They are flashing when vac is on Available and off when vac is off. to Operator SCREEN 2 Example SCREEN 3 (Diagnostic) The Diagnostic only. It
Resumo do conteúdo contido na página número 15
EN MACHINE CONTROLS & FEATURES Squeegee Lift Handle ("S Class" models only) See Figure #3a, 3b, & 3c. The squeegee lift handle is located below the control handles on the right side. It is used to raise or lower the squeegee. The vac motor is turned on when the handle is lowered. Parking Brake (Optional)See Figure #4. The parking brake prevents movement of the machine. The brake is located on the left hand side of the transaxle motor. Turn the key switch off or disconnect the power to the b
Resumo do conteúdo contido na página número 16
HOW TO PREPARE THE MACHINE FOR OPERATION 38722B How To Install The Batteries The Scrubtec machines use six 6-volt batteries. The batteries are located in the battery compartment under the recovery tank. To Install the batteries, follow this procedure: 1. Turn key switch off. 38722B 2. Make sure both tanks are empty. 3. Disconnect the hoses from the recovery tank (upper tank) & unplug the vac motor and float 38720B switch. 38722B 4. Remove the tank support bracket. Figure #6a 5. Remove the rec
Resumo do conteúdo contido na página número 17
HOW TO PREPARE THE MACHINE FOR OPERATION Battery Maintenance The electrical power to operate the machine comes from the Correct fill level storage batteries. Storage batteries need preventive main- tenance. WARNING: Working with batteries can be dan- gerous. Always wear eye protec- tion and protective clothing when working near batteries. NO SMOKING! Figure #7 To maintain the batteries in good condition, follow these instructions: 1. Keep the electrolyte at the correct level. The correct l
Resumo do conteúdo contido na página número 18
HOW TO PREPARE THE MACHINE FOR OPERATION How To Charge The Batteries WARNING: Charging the batteries in an area without adequate ventilation could result in an explosion. To prevent an explosion, charge the batteries only in an area with good ventilation. WARNING: Lead acid batteries generate gases which could explode. Keep sparks and flames away from batteries. NO SMOKING! To charge the batteries, follow this procedure: 1. Make sure the key switch is in the “OFF” position. 2. Before chargi
Resumo do conteúdo contido na página número 19
HOW TO PREPARE THE MACHINE FOR OPERATION How To Install The Brushes Or Pad Drivers To install the brushes or pad drivers on the machine, follow this procedure: 1. Turn the key switch "ON". 2. Put the brush switch in the "UP" position. 3. Turn the key switch "OFF". 4. Go to the front of the machine. 5. Unlatch right and left brush housings and remove Figure #9 them. See figure #9. 6. Put a brush or pad driver under the brush motor plate. See figure #10. 7. Align the lugs on the motor gimbal wi
Resumo do conteúdo contido na página número 20
HOW TO OPERATE THE MACHINE How to Operate the One Touch System ("L Class" models only) One touch cleaning is a feature on the new Scrubtec Walk-behind Scrubber. The factory defaults for this setting are two bars of brush pressure and four bars for solution flow and squeegee in the down position. 1. Press and release the green button for all cleaning functions to begin, see figure #11, item A. 2. The squeegee and brush head lower to the floor and the vacuum starts. NOTE: The squeegee switch mus
