Resumo do conteúdo contido na página número 1
MODEL W1774
18 GAUGE BRAD NAILER
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED DECEMBER, 2007 (JM)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9551TS Printed in China
Resumo do conteúdo contido na página número 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/equipment. Failure to read, understand, and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution, or death. The owner of this machine/equipment is solely responsible for its safe use. This responsibility includes, but is not limited to, proper installation in a safe environment, personnel training and usa
Resumo do conteúdo contido na página número 3
Model W1774 18 Gauge Brad Nailer SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper acc
Resumo do conteúdo contido na página número 4
Model W1774 18 Gauge Brad Nailer Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for the 17. DISCONNECT TOOLS before tool. Make sure your air hose is in servicing, changing accessories, or good condition and is long enough moving to another location. to reach your work without 18. DO NOT OVERREACH. Keep proper stretching. footing/balance at all times. 11. WEAR PROPER APPAREL. Do 19. USE THE RECOMMENDED not wear loose clothing, gloves, ACCESSORIES. Consult owner’s neckti
Resumo do conteúdo contido na página número 5
Model W1774 18 Gauge Brad Nailer Additional Safety for Nailers/Staplers 1. HAND INJURIES: Do not place your 5. HOSE USAGE: Make sure your air hands near the nail point of entry. hose is designed for the tool in A nail can deflect and tear through use, is in good condition, and is the surface of the workpiece, long enough to reach your work puncturing your hand or fingers. without stretching. However, an overly long air hose in the work 2. COMBUSTIBLE GASES: Never area may be a tripping h
Resumo do conteúdo contido na página número 6
Model W1774 18 Gauge Brad Nailer INTRODUCTION Woodstock Technical Machine Data Support Nail Size ............................. 18 Gauge 5 Nail Length .............................. ⁄8"–2" This Model W1774 18 Gauge Brad Nailer Magazine Capacity ................. 100 Nails has been specially designed to provide 1 Air Inlet ................................ ⁄4" NPT many years of trouble-free service. Close 1 Weight .................................3 ⁄2 lbs. attention to detail, ruggedly built p
Resumo do conteúdo contido na página número 7
Model W1774 18 Gauge Brad Nailer Compressed Air System The Model W1774 is designed to be operated at 60-100 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum operating pressure for your model. Before using your nailer, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the nailer at a low setting, then increase the air pressure as Exceeding the maximum permissible needed for satisfactory results
Resumo do conteúdo contido na página número 8
Model W1774 18 Gauge Brad Nailer SETUP Unpacking This brad nailer has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1774. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the tool or examine the packaging materials c
Resumo do conteúdo contido na página número 9
Safety Nose Model W1774 18 Gauge Brad Nailer — If the nailer fires when the trigger Safety Nose Mechanism is pulled, without the safety nose A safety mechanism on the nose of mechanism being depressed, then the nailer protects against accidental the nailer is not working properly. firing. When the trigger is pressed, the nailer will not fire until the safety nose — If you find that the safety mechanism is depressed. nose mechanism is not working properly, check the lubrication of Before
Resumo do conteúdo contido na página número 10
Model W1774 18 Gauge Brad Nailer OPERATIONS Loading When replacing nails in your Model W1774, follow these guidelines: Gauge: ........................................18 5 Length: .................................. ⁄8"–2" Capacity: ................................... 100 To load your nailer, do these steps: Figure 3. Loading nails into magazine. 1. DISCONNECT NAILER FROM THE AIR 5. Slide the nails all the way down to SUPPLY! the nose of the nailer. 2. Depress the magazine latch, as shown 6.
Resumo do conteúdo contido na página número 11
Model W1774 18 Gauge Brad Nailer 3. Depress the safety nose mechanism 5. Pull the trigger. against your workpiece. — If the nail drove into the wood 4. Before pulling the trigger, make sure far enough, continue with your your free hand and other body parts intended operations. are positioned out of the way of a potential path of a nail in case of — If the nail either went too far or deflection. not far enough, then adjust the air pressure. More air pressure will Deflection is caused wh
Resumo do conteúdo contido na página número 12
Model W1774 18 Gauge Brad Nailer Clearing Jammed Nails ���������� A jammed nail must be cleared before using the nailer again. ����������� To clear a jammed nail from the dis- charge area, do these steps: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! Figure 5. Removing guide cover. 2. Depress the magazine latch and pull 5. The jammed nail should now be back the magazine cover until it visible; remove it with needle nose stops. pliers. 3. Remove the nail stick from the 6. Throw the damage
Resumo do conteúdo contido na página número 13
Model W1774 18 Gauge Brad Nailer 6. Open the nose cover as if to clear a Replacing Pistons/ jammed nail. O-Rings 7. Watch the discharge area and push Under heavy use, a piston or piston shaft the top of the piston with your may wear out. Replacement is quick finger. You will see the piston shaft and easy. Contact your authorized Shop slide down the discharge area. Fox dealer to obtain the Piston Repair Kit (Part Number X1774068) or the 8. Taking care not to scratch or dent complete O
Resumo do conteúdo contido na página número 14
Model W1774 18 Gauge Brad Nailer CLEANING & LUBRICATION Cleaning Lubricating Use a good solvent to clean the nose Use a quality pneumatic tool oil with your assembly of the nailer. Always be sure new Shop Fox nailer to help maintain its that the nailer is dry before using it useful life. Place two to six drops of oil again. in the nailer air inlet (as shown in Figure 6) before every use, or after 2 hours of Do not allow dust, chips, sand, etc. continuous use. Wipe off any excess oil into
Resumo do conteúdo contido na página número 15
Model W1774 18 Gauge Brad Nailer W1774 PARTS BREAKDOWN -13- ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ���
Resumo do conteúdo contido na página número 16
Model W1774 18 Gauge Brad Nailer W1774 PARTS LIST REF PART � # DESCRIPTION REF PART � # DESCRIPTION 101 X1774101 SPECIAL �BOLT 136 X1774136 COMPRESSION �SPRING 102 X1774102 E XH AU S T � P OR T 137 X1774137 SAF ETY �NO SE 103 X1774103 COMPRESSION � SPRING 138 X1774138 DRIVER � GUIDE 104 XPB42M HEX � BOLT � M5-.8 � X �20 139 X1774139 S P A C E R 105 XPLW01M LOCK �WASHER �5MM 140 XPSB15M CAP � SCREW �M5-.8 � X � 20 106 X1774106 CYLINDER �CAP 141 XPSB23M CAP � SCREW �M4-.7 � X � 12 107 X1774107 O-
Resumo do conteúdo contido na página número 17
Model W1774 18 Gauge Brad Nailer Troubleshooting Symptom Possible Cause Possible Solution Air leaking at 1. O-rings in trigger valve 1. O-rings must be replaced trigger valve area. housing are damaged. & operation of safety nose must be checked. Air leaking between 1. Loose screws in housing. 1. Tighten screws. housing and hose 2. Damaged O-ring. 2. Replace O-ring 3. Loose air fitting. 3. Tighten air fitting & use teflon tape. Air leaking between 1. Damaged seal. 1. Replace damaged seals. ho
Resumo do conteúdo contido na página número 18
� � � � � � � �� � � �� � � � � � � � � � � � � � � ��� � � � � � � � � � � � � � �� � � � �� � � � � � � � �� � � �� � � � � � � � � �� � � ��� � � � �� � �� � �� � � � �� � �� � � � � � � �� � � � �� � � � � � � � � � ��� � � �� � � � � � � � � �� � � �� �� � � � � � �� � �� �� � � � �� � � � �� � � �� � � � �� � �� � � � � �� � �� � � � �� � � � �� � � �� � � � � � � � � �� � � � � �� � � � �� � � � � � � � �� � � � � �� � � �� � � � � � �� � � �� � � � �� � � �� � � � � �� � � ��� � � �� � �
Resumo do conteúdo contido na página número 19
Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email __________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following informa
Resumo do conteúdo contido na página número 20
FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE
