Resumo do conteúdo contido na página número 1
P03 / P06 / P09
®
Cod. 2850018 - Rev. 00 - Marzo 2009
Resumo do conteúdo contido na página número 2
INTRODUCTION Dear Customer, Thank you for choosing our product. This machine, thanks to its reliability, will be able to win your preference also for other products in our range. Each dealer will be able to refer you to the nearest Service Centre. Notwithstanding the ease of use of the machine, in order to get the best results it is important to thoroughly read this booklet and follow all instructions before starting the machine. GENERAL INFORMATION The machine is suitable for p
Resumo do conteúdo contido na página número 3
IMPORTANT PRECAUTIONS SAFETY REGULATIONS Make sure to implement all necessary precautions to avoid contact of the When using electric material it is important to ensure the appropriate machine with liquids. Liquids can seep inside the machine and cause short- precautions are adopted in order to avoid electric shock, accidents circuits or energise external parts of the machine. and damage to persons and things. • Thoroughly read all information contained in this manual and in any INTEN
Resumo do conteúdo contido na página número 4
• Check that the power supply cable is not damaged or defective. If CLEANING there is a problem, do not use the machine under any Before starting any cleaning on the machine, ensure that it is switched off circumstances. The power supply cable must be replaced by the and that the plug is unplugged. manufacturer or by one of its service centres. Wait several minutes to allow the components to cool down. Do not insert any objects in the holes of the machine. Pay attention to the positio
Resumo do conteúdo contido na página número 5
OPERATING INSTRUCTIONS CONTROL PANEL F03 F06 F09 1 Drip tray The figure shows the F09, 2 Cup support grille which has 3 canisters. The 3 Canister of product A 3 Canister of product B F06 and F03 versions differ 3 Canister of product C from this in number of 4 Door canisters, respectively 2 and 5 Water level sensor 1 6 Water tank 7 Main switch 8 Control panel 7 8
Resumo do conteúdo contido na página número 6
PRELIMINARY OPERATIONS • As indicated in the figures of the previous page, the machines have 2 Before inserting the plug and switching the machine on, remove the water dispensing buttons for each granulated product: tank, thoroughly rinse it and fill it with fresh water. - Large cup: long dose Replace the tank, ensuring that the level sensor is immersed in the water. - Small cup: short dose Pour in the tank only fresh drinking still water. Hot water or other liquids In addition, they have
Resumo do conteúdo contido na página número 7
STARTING THE MACHINE N.B.: the machine requires little time for heating, if not For correct dispensing, it is important that the used in the immediate future, it is advisable to switch it off. product inside the canister never falls below this level. After completing the preliminary operations, place a large enough container in the drink dispensing point. NOTE: the different configurations of the machine allow one or more Make sure the main switch is set to the position “
Resumo do conteúdo contido na página número 8
Pay attention now, the display will indicate the message “READY - SEL.PRODUCT“ and at this point it will be possible to dispense the desired drink by pressing the corresponding button. Periodically wash the water tank and replace the water. Using a soft cloth damp with warm water, clean the outside of the softener filter and the intake tube to which it is fitted. INSTRUCTIONS FOR ROUTINE CLEANING N.B.: The softener filter operates correctly up to 35 litres of water, after which it must b
Resumo do conteúdo contido na página número 9
TROUBLE-SHOOTING • The machine dispenses too little water: replace the resin filter fitted on the water intake tube and located inside the water tank. • The machine dispenses one drink and then stops: check the water level in the tank and if necessary refill it or verify that the shut-off valve is open. • The powder is not dispensed: check that the product canister is correctly inserted in its seat and/or there is sufficient product. • There is a water leak between component Z and
