Resumo do conteúdo contido na página número 1
TM 11-6625-2958-14& P
TECHNICAL MANUAL
OPERATOR’S, ORGANIZATIONAL,
DIRECT SUPPORT AND GENERAL SUPPORT
MAINTENANCE MANUAL
(INCLUDING REPAIR PARTS
AND SPECIAL TOOLS LIST)
FOR
POWER SUPPLY PP-7545/U
(HEWLETT-PACKARD MODEL 6269B)
(NSN 6130-00-148-1796)
HEADQUARTERS, DEPARTMENT OF THE ARMY
21 AUGUST 1980
Resumo do conteúdo contido na página número 2
SAFETY STEPS TO FOLLOW IF SOMEON E IS THE VICTIM OF ELECTRICAL SHOC K DO NOT TRY TO PULL OR GRAB THE INDIVIDUA L IF POSSIBLE , TURN OFF THE ELECTRICAL POWE R IF YOU CANNOT TURN OFF THE ELECTRICA L POWER, PULL, PUSH, OR LIFT THE PERSON T O SAFETY USING A WOODEN POLE OR A ROPE O R SOME OTHER INSULATING MATERIA L SEND FOR HELP AS SOON AS POSSIBL E AFTER THE INJURED PERSON IS FREE O F CONTACT WITH THE SOURCE OF ELECTRICA L SHOCK, MOVE THE PERSON A SHORT DISTANC E AWAY AND IMMEDIATELY START ARTIFICI
Resumo do conteúdo contido na página número 3
This manual includes copyright material reproduced by permission of the HEWLETT-PACKARD Company. TM 11-6625-2958-14&P TECHNICAL MANUAL HEADQUARTERS DEPARTMENT OF THE ARMY No. 11-6625-2958-14&P Washington DC, 21 August 1980 OPERATOR’S, ORGANIZATIONAL, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE MANUA L (INCLUDING REPAIR PARTS AND SPECIAL TOOLS LISTS) FOR DC POWER SUPPLY PP-7545/U (HEWLETT-PACKARD MODEL 6269B) (NSN 6130-00-148-1796) FOR SERIALS 1027A00101 AND ABOVE* REPORTING OF ERRORS You can
Resumo do conteúdo contido na página número 4
TABLE OF CONTENTS Section Page No. Section Page No. 3-22 Optional Operating Modes 0 INSTRUCTIONS . . . . . . . . . . . . . . . 6-1 3-3 3-23 Remote Programming, 0-1 Scop e 0-1 0- 1 Constant Voltage 0-2 Indexes of Publications 3-3 3-32 Remote Programming, 0-3 Forms and Records 0-1 Constant Current 3-4 0-4 Reporting Equipment Im- 3-41 Remote Sensing 3-5 provement Recom- 3-46 Auto-Parallel Operation 3-6 mendations (EIR) 0- 1 3-50 Auto-Series Operation 0- 1 3-7 0-5 Administrative Storage 3-55 Auto-T
Resumo do conteúdo contido na página número 5
TABLE OF CONTENTS (Continued) Sectio n Page No. Sectio n Page No. V MAINTANCE . . Continued 5-111 Crowbar Disablement 5-22 5-103 Preregulator Tracking (5 O and 60Hz Operation) 5-21 VI REPLACEABLE PARTS . . . . . . . . . . . ...6-1 5-105 50Hz Operation (Option 005) 5-21 6-1 Introduction 6-1 5-107 Crowbar Trip Voltage 5-21 6-4 Ordering Information 6-1 5-109 Maximum Crowbar Trip Voltage 5-22 VII CIRCUIT DIAGRAMS & COMPONENT LOCATION DIAGRAMS . . . . . . . . . . . 7-1 Page No. APPENDIX A . Reference
Resumo do conteúdo contido na página número 6
LIST OF ILLUSTRATIONS Page No. Figure 1-1 DC Power Supply, Model 6259B, 6260B, 6261B, 6268B, or 6269B . . . . . . . . . . . .. l-l 2-1 2-1 Outline Diagram . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Bias Transformer Primary Connections for 208Vac and 115Vac Operation . . . . . . .2-2 2-3 Power Transformer Primary Connections for 208Vac and 115Vac Operation . . . ...2-2 2-4 Power Transformer T1 Primary Connections for 208Vac Ope
Resumo do conteúdo contido na página número 7
TM 11-6625-2958-14&P SECTION O INTRODUCTIO N 0-1. SCOPE. 4430.3E and DSAR 4140.55. c. Discrepancy in Shipment Report (DISREP) a. This manual describes DC Power (SF 361). Fill out and forward Discrepancy in Supply PP-7545/U (fig. l-l) an d Shipment Report (DISREP) (SF 361) as prescribed provides maintenance instructions. Throughout this manual, PP-7545/U in AR 55-38/NAVSUPlNST 4610.33B/AFR 75- is referred to as the Hewlett-Pack- 18\MCO P4610.19C and DLAR 4500.15. ard (HP) Model 6269B DC Power 0-4
Resumo do conteúdo contido na página número 8
TM 11-6625-2958-14&P SECTION I GENERAL INFORMATION Figure 1-1. DC Power Supply, Model 6259B, 6260B, 6261B, 6268B, or 6269B 1-1 DESCRIPTION 1-4 The power supply has rear output terminals. Either the positive or negative output terminal may 1-2 This power supply, Figure 1-1, is completely be grounded or the power supply can be operated transistorized and suitable for either bench or relay floating at up to a maximum of 300 volts above rack operation. It is a well-regulated, constant ground. voltag
Resumo do conteúdo contido na página número 9
TM 11-6625-2958-14&P may be used in series when a higher output voltage Option No. Description is required in the constant voltage mode of opera- 014 Three Digit Graduated Decadial Cur- t ion or when greater voltage compliance is required rent Control: A single control that in the constant current mode of operation. Auto- replaces the coarse current control Series operation permits one-knob control of the and allows accurate resetting of the total output voltage from a “master” supply. output cu
Resumo do conteúdo contido na página número 10
TM 11-6625-2958-14&P 1-14 ORDERING ADDITIONAL MANUALS your local Hewlett-Packard field office (see list at rear of this manual for addresses). Specify the 1-15 One manual is shipped with each power sup- model number, serial number prefix, and HP part ply. Additional manuals may be purchased from number shown on the title page. Table 1-1. Specifications INPUT: METERS: A front panel voltmeter (0-50V) and ammeter 230Vac *10%, single phase, 57-63 Hz, 18A, 2500W @ 230V. (0-60A) is provided. (Accurate
Resumo do conteúdo contido na página número 11
TM 11-6625-2958-14&P SECTION II INSTALLATION 2-1 INITIAL INSPECTION 2-2 Before shipment, this instrument was inspect- ed and found to be free of mechanical and electri- cal defects. As soon as the instrument is unpacked, inspect for any damage that may have occurred in transit. Save all packing materials until the in- spection is completed. If damage is found, file a claim with the carrier immediately. Hewlett- Packard Sales and Service office should be notified. 2-3 MECHANICAL CHECK 2-4 This ch
Resumo do conteúdo contido na página número 12
TM 11-6625-2958-14&P transformer (see Figure 2-2 B). Leave wire from fan B2 (not used in 62599) soldered to “230V” terminal. c. Re-install RFI assembly by reversing pro- cedure of Step (a). d. Unsolder wire connected to terminal 5 of power transformer T1 (see Figure 7-4) and solder it instead to terminal 4 of transformer (see Figure 2-3 B). Figure 2-3. Power Transformer Primary Connections for 208Vac and 115Vac Operation . (Model 6259B, 6261B, and 6268B) Figure 2-2. Bias Transformer Primary Conn
Resumo do conteúdo contido na página número 13
TM 11-6625-2958-14&P Figure 2-4. Power Transformer T 1 Primary Connections for 208Vac Operation (Model 6260B and 6269B) of power transformer T1 (see Figure 7-4) and solder it instead to "208V" terminal of transformer (see Figure 2-5. RFI Choke (A2L1A/A2L1B) Figure 2-4 B). Connections for 115Vac Operation (Model 6259B, 6260B, 6261B, and 6268B) 2-21 CONNECTIONS FOR 115 VOLT OPERATION (Model -6259B, 6261B, and 6268B: Option 026) fan B2 is not used in Model 6259B. 2-22 To convert Model 6259B, 6261B,
Resumo do conteúdo contido na página número 14
TM 11-6625-2958-14&P b. Perform Steps (b) through (e) of Paragraph grounded) and be of sufficient wire size to handle 2-22. the input current drawn by the supply (see Paragraph 2-16). Note that when the supply is operated from 2-25 CONNECTIONS FOR 50Hz OPERATION a 115Vac source, the input current is approximately double that shown in Paragraph 2-16. 2-26 For operation from a 50Hz ac input, R82 must be replaced with a 240 Ω, ±5%, ½ watt resistor 2-29 REPACKAGING FOR SHIPMENT as specified under O
Resumo do conteúdo contido na página número 15
TM 11-6625-2958-14&P SECTION Ill OPERATING INSTRUCTIONS Figure 3-1. Front Panel Controls and Indicators,’ Modal 6259B, 6260B, 6261B, 6268B or 6269B 3-1 TURN-ON CHECKOUT PROCEDURE 3-3 OPERATING MODES 3-2 The following checkout procedure describes 3-4 The power supply is designed so that its mode the use of the front panal controls and indicators of operation can be selected by making strapping (Figure 3-1) and ensures that the supply is opera- connections between particular terminals on the ter-
Resumo do conteúdo contido na página número 16
TM 11-6625-2958-14&P Clockwise rotation of the control produces higher trip voltages. The factory sets the control fully clockwise. The crowbar may be disabled complete- ly if desired. (Refer to Paragraph 5-11 1.) 3-13 False crowbar tripping must be considered when adjusting the trip point. If the trip voltage is set too close to the operating output voltage of the supply, a transient in the output will falsely trip the crowbar. It is recommended that the crowbar be set higher than the output vo
Resumo do conteúdo contido na página número 17
TM 11-6625-2958-14&P then proceed at a slower rate towards zero. The 3-26 The output voltage of the supply should be -15mV ±5mV when zero ohms is connected across actual time required for the output to fall from two volts to zero will vary from several seconds to the programming terminals. If a zero ohm voltage closer to zero than this is required, it may be several minutes, depending upon which down-pro- gramming method is used. achieved by inserting and adjusting R110 as dis- cussed in Paragra
Resumo do conteúdo contido na página número 18
TM 11-6625-2958-14&P Figure 3-6. Remote Resistance Programming (Constant Current) Figure 3-5. Remote Voltage Programming, Non-Unity Gain (Constant Voltage) with Option 021, by adjusting potentiometer R116 as discussed in Paragraph 5-98. The output current of the supply when zero ohms is placed across the (less than 30ppm Per degree Centigrade) character- istics in order to maintain the Supply's temperature programming terminals may be set to exactly zero and stability specifications. Reference r
Resumo do conteúdo contido na página número 19
TM 11-6625-2958-14&P programmed using an external voltage source with variable gain by utilizing the strapping pattern shown in Figure 3-8. In this mode, the output cur- rent is found by multiplying the external voltage source (Es) by [Rp/(RR x Kp)], where Kp is the constant current voltage programming coefficient as given in Paragraph 3-37. The value of reference resistor RR and programming voltage source E s should be such that the value of ES/RR is equal to or greater than 2.5mA. 3-39 Externa
Resumo do conteúdo contido na página número 20
TM 11-6625-2958-14&P from the -S terminal to the negative side of the load. 3-43 For reasonable load lead lengths, remote sensing greatly improves the performance of the Note that there may be more than one lead connect- ed to the +S and -S terminals. supply. However, if the load is located a consid- erable distance from the supply, added precautions 3-46 AUTO-PARALLEL OPERATION (Figure 3-10) must be observed to obtain satisfactory operation. Notice that the voltage drop in the load leads sub- t
