Resumo do conteúdo contido na página número 1
LM95235 Evaluation Board User’s Guide
Revision A
April 14, 2006
LM95235 Evaluation Board User’s Guide
© Copyright 2006 National Semiconductor Corporation 1 www.national.com
Resumo do conteúdo contido na página número 2
LM95235 Evaluation Board User’s Guide Table of Contents Table of Contents 2 References 3 1.0 Introduction 4 2.0 Quick Start 5 3.0 Functional Description 7 4.0 Software Installation and Operation 8 5.0 Electrical and Mechanical Specifications 9 5.1 Electrical Specifications 9 5.2 Electrical Schematic 9 5.3 Evaluation Board Layout 10 5.4 Bill of Materials 11 5.5 Mec
Resumo do conteúdo contido na página número 3
LM95235 Evaluation Board User’s Guide References 1. “LM95235 Precision Remote Diode Temperature Sensor With SMBus Interface and TruTherm™ Technology” datasheet. The latest copy of the LM95235 datasheet can be obtained by going to the National Semiconductor website www.national.com, by searching on “LM95235”, and then downloading the LM95235.pdf file. 2. SensorEval Version 1.1.0a or later, Evaluation Board CD containing: a. The SensorEval.exe executable program used to r
Resumo do conteúdo contido na página número 4
1.0 Introduction The LM95235 Evaluation Board is used together The block diagram below describes the LM95235 with the National Semiconductor SensorEval Evaluation Board itself. The USB input provides the software (provided in the kit), and with a USB cable +5.0 VDC power to the board, which is regulated (not provided in the kit), and with an external down to 3.3 VDC to power the IC’s. The EEPROM personal computer (PC). Power to the LM95235 is programmed at the factory with a unique
Resumo do conteúdo contido na página número 5
2.0 Quick Start 1. Install the CD into the CD drive of the computer and install the SensorEval software (see Section 4.0). 2. Hookup the USB cable between the PC or notebook computer and the LM95235EVAL board as shown in Quick Start Diagram (See Section 2.1). 3. Run the SensorEval software clicking the icon on the desktop. The first screen after the installation will look like this: Select the LM95235 Evaluation Board. Click OK. 5. The next screen will l
Resumo do conteúdo contido na página número 6
6. The Screen should look like this: . The user can also select the 3904 diode or the Local (on-chip) and remote temperatures should read processor thermal diode called “90 nm”. continuously. The user can experiment with the different settings of Address BF. 7. If the user clicks the 06-FF tab the next screen will look like this: The user can experiment with the Mask settings. Also the user can change the conversion rate. The next screen shows the possi
Resumo do conteúdo contido na página número 7
8. If the user clicks on the Start Plot button a graph box will appear and will graph the temperature. An example is shown below 9. If the user selects the Start Log button the following screen will appear. The user then enters the filename that he chooses to log the data into. © Copyright 2006 National Semiconductor Corporation 7 www.national.com
Resumo do conteúdo contido na página número 8
2.1 Quick Start Diagram Important! NO EXTERNAL POWER SUPPLY OR SIGNAL INPUTS ARE REQUIRED! N/C USB Cable to TCRIT# Computer N/C OS/A0 SCL SDA LM95235 +3.3 JP2 Computer with SensorEval software loaded National Semiconductor LM95235 Evaluation Board Rev. 1 © Copyright 2006 National Semiconductor Corporation 8 www.national.com
Resumo do conteúdo contido na página número 9
Power to the LM95235 Evaluation Board is taken 3.0 Functional Description from the USB 5-Volt line. This +5 VDC is the input to the on-board LM2950 low dropout voltage The LM95235 Evaluation Board, along with the regulator, which regulates the output voltage to +3.3 SensorEval Software, provides the system designer VDC. This output voltage powers the LM95235, the with a convenient way to learn about the operation of on-board microcontroller, and the EEPROM chip the LM95235 Te
Resumo do conteúdo contido na página número 10
4.0 Software Installation and Operation 4.1 Installation 4.2 Operation The CD provided in the LM95235 Evaluation Board Kit contains the SensorEval software used to make the LM95235 Follow the following procedure for operation the LM95235 Evaluation Board operate with the user’s PC. It is assumed Evaluation Board using the SensorEval software: that the user will be using a PC with a Pentium ® III or higher 1. Run the SensorEval program by either double- processor and Mi
Resumo do conteúdo contido na página número 11
5.0 Electrical and Mechanical Specifications 5.1 Electrical Specifications Power Requirements The Board uses the +5.0 VDC and GND lines from the USB connection. +5.0 ± 0.1 V, This +5.0 VDC voltage is regulated down to +3.3 VDC for board power. 100 mA max. * NO EXTERNAL POWER SUPPLY INPUTS ARE REQUIRED * 5.2 Electrical Schematic + 3.3 VDC TP1 Use a 0.1 uF capacitor for each + 3.3 VDC GND Vcc pin of U2 and Reserved_6 pin. C1 C2 C3 C4 C5 C6 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
Resumo do conteúdo contido na página número 12
5.3 Evaluation Board Layout Figure 5.3 Layout diagram of the LM95235 Evaluation Board (Note: socket and socket area not stuffed.) © Copyright 2006 National Semiconductor Corporation 12 www.national.com
Resumo do conteúdo contido na página número 13
5.4 Bill of Materials for LM95235 Evaluation Board Item Qty Reference Part PCB Footprint 1 11 C1,C2,C3,C4,C5,C6, Capacitor, SMD, ceramic, 0.1uF sm/c_0805 C12,C15,C17,C20 2 2 C9, C10 Capacitor, SMD, ceramic, 33 pF sm/c_0805 3 3 C11,C14,C16 Capacitor, SMD, ceramic, 2.2 uF sm/ct_3216_12 4 2 C13,C19 Capacitor, SMD, ceramic, 100 pF sm/c_0805 5 1 J3 Connector, USB-B tm/usb_typeb 6 1 J4 HEADER 2x2 blkcon.100/vh/tm1sqs/w.100/4 7 1 L1 sm/l_1206 Filter, 1uH, Stewart MI1206K90
Resumo do conteúdo contido na página número 14
5.4 Mechanical Specifications 5.4.1 Operating Mechanical and Environmental Specifications Minimum Typical Maximum Temperature 0 °C 25 °C 70 °C 5.4.2 Evaluation Board Basic Dimensions 2.45 in/6.22 cm 3.25 in/8.76 cm 5.4.3 Electrostatic Discharge (ESD) Precautions The user shall use ESD precautions as specified in National Semiconductor ESD control document (SC)CSI-3-038 available through www.national.com. © Copyright 2006 National Semiconductor Corporation 14 www.nationa
Resumo do conteúdo contido na página número 15
BY USING THIS PRODUCT, YOU ARE AGREEING TO BE BOUND BY THE TERMS AND CONDITIONS OF NATIONAL SEMICONDUCTOR'S END USER LICENSE AGREEMENT. DO NOT USE THIS PRODUCT UNTIL YOU HAVE READ AND AGREED TO THE TERMS AND CONDITIONS OF THAT AGREEMENT. IF YOU DO NOT AGREE WITH THEM, CONTACT THE VENDOR WITHIN TEN (10) DAYS OF RECEIPT FOR INSTRUCTIONS ON RETURN OF THE UNUSED PRODUCT FOR A REFUND OF THE PURCHASE PRICE PAID, IF ANY. The LM95235 Evaluation Boards are intended for product evaluation pu
