Resumo do conteúdo contido na página número 1
Hickory Industries, Inc.
Installation Manual
USA
Hickory Rotisseries
Models: N/5.5 E
Machine Type N / 5. 5 E
Total Power Rating 6000 or 8400 Watts
Elements / Spits 4 Elements with 5 Spits
Electrical Rating 208/240 V or 380/410 V
T emperature Range
200ºF - 550ºF
Timer Manual or Fully Automatic
Delivery Date: Final Inspection:
4900 Westside Avenue, North Bergen, New Jersey 07047 N/5.5E Installation 8/5/97
Tel: [201] 223-0050 Fax: [201] 223-0950 Page 1 of 15
Resumo do conteúdo contido na página número 2
Hickory Industries, Inc. Table of Contents 1.0 Installation Instructions 3 1.1 General Information 4 1.2 Description of the Data Plate 4 1.3 Machine Drawings and Dimensions 6 1.4 Electrical Conversion and Adjustment Instructions 7 1.5 Cooking Cycle 7 1.6 Maintenance, Response to Technical Problems 7 1.6.1 Reasons for Problems and Solutions 8 1.7 Spit Drive Mechanism 9 1.8 N/5.5E Parts List 10 1.9 N/5.5E Exploded View 12 4900 Westside Avenue, North Bergen, New Jersey 07047 N/5.5E Insta
Resumo do conteúdo contido na página número 3
Hickory Industries, Inc. 1.0 Installation Instructions a. When installing these units, it is important to comply with the most recently established rules and regulations as deemed pertinent by the local and national electrical, ventilation, sanitation, and fire codes. These units are classified by Underwriters Laboratories, Inc. as Electrically Heated Food Service Equipment. b. Electric units must not be directly connected to a flue or exhaust vent. However, electric units may require operati
Resumo do conteúdo contido na página número 4
Hickory Industries, Inc. 1.1 General Information The Operating Instructions are to be given to the operator of the rotisserie. All unit operators are to be familiar with the functions of the rotisserie. The Operating Instructions should be kept in a location close to the rotisserie. It should be easily recognizeable and easily accessible. Electric units can be ordered to meet most electrical specifications. It is recommended that a repair and maintenance contract be signed with the manufacture
Resumo do conteúdo contido na página número 5
Hickory Industries, Inc. HICKORY INDUSTRIES, INC. HICKORY INDUSTRIES, INC. NORTH BERGEN, NJ 07047 NORTH BERGEN, NJ 07047 MODEL: N/5.5 E M SERIAL NO. MODEL: N/5.5 E M SERIAL NO. MOTOR: 208 - 220 VOLTS 60 CYCLE AC CURRENT MOTOR: 110 - 120 VOLTS 60 CYCLE AC CURRENT WATTS SINGLE PHASE 3 RPM WATTS SINGLE PHASE 3 RPM HEATING ELEMENTS 208 VOLTS 60 CYCLE HEATING ELEMENTS 208 VOLTS 60 CYCLE
Resumo do conteúdo contido na página número 6
Hickory Industries, Inc. 1.3 Machine Drawings and Dimensions The following drawing of the Front View, Side View, and Top View indicate where the dimensions are taken and should be used to plan the installation of the units. N/ 5.5 E Top View Front View Right Side View N/ 5.5 E inches mm Height 29" 737 Width 39-1/4" 997 Depth 22-1/16" 560 4900 Westside Avenue, North Bergen, New Jersey 07047 N/5.5E Installation 8/5/97 Tel: [201] 223-0050 Fax: [201] 223-0950 Page
Resumo do conteúdo contido na página número 7
Hickory Industries, Inc. 1.4 Electrical Conversion and Adjustment Instructions Before converting or adjusting the machine to another type of electricity, it is imperative that electrical power to the machines should also be turned off. When converting, make sure that the proper electrical diagram is followed and that the motor and timer match the connected single phase voltage! 1.5 Cooking Cycle In order to start the cooking cycle, the elements must be powered. The heating cycle will start onl
Resumo do conteúdo contido na página número 8
Hickory Industries, Inc. 1.6.1 Reasons for Problems and Solutions Problem Cause Solution Unit does not heat. a. Rotisserie not "on". 1. Make sure that the TEMPERATURE switch is on. 2. Thermostat must be set (i.e. 550°F). The cooking timer must be operational (cook cycle). 3. A red LED on the TEMPERATURE switch indicates that the contactor is supplying power to the heating elements. 4. Using the electrical diagram, make sure that the entire system is fully functional. Unit takes too a . T e
Resumo do conteúdo contido na página número 9
Hickory Industries, Inc. 1.7 Spit Drive Mechanism This unit is equipped with a planetary motion spit drive system. This means that each spit is turning upon its axis at the same time that they turn about the center shaft. When the motor switch is turned to on, the disks and the spits will begin to turn. Insure that the mechanism turns smoothly when testing the unit. Center Shaft Aluminum Drive Disk Spit Before cooking, it is imperative that the center shaft be covered and protected with alumi
Resumo do conteúdo contido na página número 10
Hickory Industries, Inc. 1.8 N/5.5E Parts List Item Qty. Description Material Length Size Manufacturer 553 1 Shaft 5/8 (Removable Drums - Center) S S 5/8" Hickory 554 1 Shaft Locking Slide S S Hickory 519 1 Drive Bearing Holder (Left - with brass bearing) Steel (Chromed) Hickory 520 1 Drive Bearing Holder (Right - with teflon bearing) Steel (Chromed) Hickory 1 Brass Shaft Bearing Brass Hickory 566 1 Teflon Shaft Bearing Teflon Hickory 501 1 Aluminum Disk Drive (Bare) Cast Aluminum
Resumo do conteúdo contido na página número 11
Hickory Industries, Inc. 1.8 N/5.5E Parts List (Contd.) Item Qty. Description Material Length Size Manufacturer 123 1 Electrical Grounding Cap Hickory Electrical Wire Janor Wire 106 1 Buchanan Contact Section 824 Buchanan 107 1 Buchanan Contact Section 830 Buchanan 550 1 Relay (Contactor) 3 Pole 220V GE 1 Capacitor GE 525 8 Element Holder Hickory 129 4 Element Porcelain Insulator Hickory 523 4 Element, Straight 220 V - 1400 Watt Glenn 524 4 Element, Straight 240 V - 1400 Watt Gle
Resumo do conteúdo contido na página número 12
Hickory Industries, Inc. 1.8 N/5.5E Exploded View 4900 Westside Avenue, North Bergen, New Jersey 07047 N/5.5E Installation 8/5/97 Tel: [201] 223-0050 Fax: [201] 223-0950 Page 12 of 15
Resumo do conteúdo contido na página número 13
Hickory Industries, Inc. Glass Replacement on the 5.5E & 10.10E Machines Make sure that the handle and all associated hardware Make sure that the handle and all associated hardware is available at the site or order the mounting kit from is available at the site or order the mounting hardware from Hickory. Hickory. Make sure that the glass bar is in the open Glass handle, flat washer, lock washer, 10/32 screw position. Glass Closed Position The glass mounts between the glass handle an
Resumo do conteúdo contido na página número 14
Hickory Industries, Inc. Replacing the front glass DO NOT TIGHTEN. This will ensure that you have Insert the screw on to the glass (use hi heat Loc-tite). enough play to move the glass around without As a hint, start with the middle screw it will give you bumping the glass. some leverage with the glass. Proceed with the remaining screws (use hi heat Loc- tite). Make sure that the glass is sandwiched be- tween silicone washer and the silicone spacer. Silicone Washer Silicone Spacer Slowly turn
Resumo do conteúdo contido na página número 15
Hickory Industries, Inc. If the glass is not evenly spaced, adjust the glass until its evenly spaced. CAUTION: If the screws are not snug enough, when lowering the glass door, the glass my hit the screws and chip the glass. CAUTION: When tightening the screws, if the glass shifts down, the glass door will be too close to the roof of the machine when the glass door is shut. Open door and tighten upper mounting screws. Close the door and verify that the side and bottom spacing is even all around.
