Resumo do conteúdo contido na página número 1
User’s Ｍａｎｕａｌ
POS Workstation
Model No. JS-950 Series
Contents
For USA / For CANADA
English
Read Me First …..….……..... 2
1.Getting Started
2.Operation
3.Appendix
Before operating this product,please read the instructions carefully,
and save this manual for future use.
Resumo do conteúdo contido na página número 2
■ For USA Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, If not installed and used in accordance with the i
Resumo do conteúdo contido na página número 3
English Read Me First Introduction Thank you for purchasing the JS-950 series Panasonic POS Workstation. This manual describes the instructions for the POS Workstation. Please read this manual carefully before using this product. List of JS-950 series Product Name Model Number. Remarks JS-950WS-040 CPU:3.2GHz,Memory:512MB or 1GB Main Unit POS Workstation JS-950WS-050 CPU:3.2GHz,Memory:2GB JS-950D2R010 12” resistive Touch screen JS-950D2C020 12” capacitive Touch screen Display
Resumo do conteúdo contido na página número 4
1. Getting Started ■ Precautions [POS Workstation: JS-950 series] IMPORTANT Install a socket outlet adjacent to the equipment so that it will be easily accessible. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 1. Avoid Radio Frequency Interference Do not place the POS Workstation near a television or radio receiver. 2. Avoid Stacking Do not place heavy objects on the POS Workstation. 3. Keep S
Resumo do conteúdo contido na página número 5
■ Name of each part & function 1 4 2 3 5 6 1. Operator’s Display 2. Front SW cover 3. POP Holder 4. Rear Display 5. USB connector 6. Power SW Attention: Do not push Power SW by mistake when you insert the USB connector. 4
Resumo do conteúdo contido na página número 6
2. Operation ■ AC Cord Kit Installation 1. How to install the AC Cord (1) Carefully lay the Main Body Unit on a clear, flat surface as shown in figure (1). (2) Unpack the AC Cord, and then connect it to AC Inlet as shown in figure (2). (3) Fit the Cord Clamp to AC Cord, and fix it by attached screw as shown in figure (3)-1, 2 and 3. (4) Carefully replace the Main Body Unit in upright position as shown in figure (4). (1) (2) (3)-1 AC Inlet (3)-2 (3)-3 (4)
Resumo do conteúdo contido na página número 7
■ Display Unit Installation Be sure to disconnect the power cable of the main block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. How to install the display unit (1) Open the screw cover of the main unit (POS Workstation). (2) Hold the display unit with both hands and insert the connector section of the display unit into the connector inlet guide of the main unit slowly to connect the connector. Note: When the connector section is connected
Resumo do conteúdo contido na página número 8
■ Storage Unit Installation Be sure to disconnect the power cable of the main block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. How to mount the storage unit (1) Disconnect the 2 latches on the upper portion of the filter cover of the main unit by both hands, pull the cover toward you while pressing the cover downward at the same time, and remove the filter cover. (2) Insert the storage unit into the prescribed inlet of the main unit slowly
Resumo do conteúdo contido na página número 9
■ Rear Display Unit Installation Be sure to disconnect the power cable of the main block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. How to mount the rear display unit (1) Loosen the thumbscrew on the lower portion of the rear cover at the rear display side of the main unit by hand, and remove the rear cover. * The thumbscrew shall be loosened until the screw rotates without resistance. (2) Prepare a rear display to be used. (The contents
Resumo do conteúdo contido na página número 10
2. How to replace the rear display (1) Loosen the thumbscrew on the lower portion of the rear cover of the main unit by hand, and remove the rear cover. * The thumbscrew shall be loosened until the screw rotates without resistance. (2) Disconnect the connector of the rear display from the connector of the main unit. (3) Loosen the 2 thumbscrews securing the rear display, and remove the rear display. * The thumbscrews shall be loosened until the screws rotate without resistance. (4)
Resumo do conteúdo contido na página número 11
■ 2nd display unit Installation Be sure to disconnect the power cable of the main block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. How to mount the 2nd Display Unit (1) Loosen the thumbscrew on the lower portion of the rear cover at the rear display side of the main block by hand, and remove the rear cover. * The thumbscrew shall be loosened until the screw rotates without resistance. (2) Prepare a 2nd display unit to be used. (The conte
Resumo do conteúdo contido na página número 12
2. How to replace the 2nd Display Unit (1) In case of 950SD010, disconnect VGA cable and speaker cable from I/O panel. (2) Loosen the thumbscrew on the lower portion of the rear cover of the main block by hand, and remove the rear cover. * The thumbscrew shall be loosened until the screw rotates without resistance. (3) Disconnect the connector of the 2nd Display Unit from the connector of the main block. (4) Prepare a new rear display. (5) Follow the steps (3), (4) and (5) of “How to
Resumo do conteúdo contido na página número 13
■ ID module Unit installation Be sure to disconnect the power cable of the main block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. Contents Peripheral screw Cable cover (Use only ID module 1pcs Screw 2pcs 2pcs Long type 1pcs Dallas KEY reader) Short type 1pcs Cable clamp 1pcs 2. How to mount the ID module unit (Please see the following pictures.) (1) Place the main unit to make the display unit at right angle to the mo
Resumo do conteúdo contido na página número 14
Tighten the screw to clamp the cable and wiring the cable as shown in the fig. (10)-4. (11) Slide USB cable cover as shown in the fig. (11)-1. In case of Dallas KEY reader, slide the USB cable cover with care to avoid the cable from the rib of the USB cable cover as shown in the fig. (11)-2. (12) Put the supplied 2 peripheral screws in from the front side of the ID module unit and tighten the screws using a screwdriver from the rear side to secure it. (13) Install Display Unit according
Resumo do conteúdo contido na página número 15
(11)-1 (11)-2 (12) Rib 3. How to replace the ID module unit (1) Remove Display Unit according to Display Unit Installation. (2) Prepare an ID module unit to be used. * The ID module unit is supplied with 2 pieces of peripheral screws, 2 pieces of screws, 1 piece of long cable cover, and 1 piece of short cable cover as accessories. (3) Slide the USB cable cover toward you while pushing both sides of the USB cable cover at the hinge section of the display unit inward to
Resumo do conteúdo contido na página número 16
3. Appendix ■ Specifications [Common Specifications] Environmental condition Item Specification Operating Temperature +5°C – +40°C Operating Humidity 15% RH – 85% RH (no dew) Strage Temperature -30°C – +60°C Strage Humidity 10%RH – 90%RH [POS Workstation: JS-950WS- ・・・ ] Item Specification Power Supply input AC100V-240V, 50/60 Hz, 6.0A Size Approx. W250mm x D277mm x H351mm Mass Approx. 7.0 kg Standard Safty cULus, TÜV, CE, GOST, BSMI, SABS EMI & FCC Part15 Class A,
Resumo do conteúdo contido na página número 17
IO Connector layout (1) Bottom IO Connector layout USB4(+24V) COM 3 LINE-OUT Printer LAN (Powered) MIC USB3(+12V) ○○○○ ○ ○○○○ ○○○○ ○ ○○○○ ○○○○ ○○○○ ○ ○○○ ○○○○ ○○○○ ○ ○○○○ ○ ○○○○ ○ ○○○○ ○ ○○○○ ○ ○○○○ ○○○○ ○○○○ ○ ○○○○ C/D2 USB1 USB2 COM 2 C/D1 COM 1 COM 4 VGA (Powered) (2) Rear Display Connector Layout Top of main block VFD 2lines (COM6) 2nd Display T/P & VFD 4 Lines (COM6) (3) Front IO Connector layout SW & LED USB #5 LAN L
Resumo do conteúdo contido na página número 18
Outside drawing Main Body 12” Touch Screen 15” Touch Screen 17
Resumo do conteúdo contido na página número 19
[Touch Display Unit: JS-950D・・・・・ ] Item Specification Size 12.1”: Approx. W320mm x D153mm x H256mm 15”: Approx. W364mm x D153mm x H300mm Mass 12.1”: Approx. 3.4 kg 15”: Approx. 4.4 kg Outside drawing (1) 12.1” resistive TP Display, 12.1” capacitive TP Display (2) 15” resistive TP Display, 15” capacitive TP Display 18
Resumo do conteúdo contido na página número 20
[Storage module Unit: JS-950H・・・・・ ] Item Specification Size Approx. W171mm x D126.5mm x H34mm Mass Approx. 0.8Kg (3.5”), 0.5Kg(2x CF) Outside drawing 3.5HDD module, Dual CF module 19
