Краткое содержание страницы № 1
4-087-364-11 (2)
US
FR
Flat Panel Color Television
Operating Instructions
Mode d’emploi
KZ-32TS1
ES
Manual de instrucciones
KZ-42TS1
© 2001 Sony Corporation
Краткое содержание страницы № 2
Note to CATV system installer WARNING This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines To Reduce the risk of fire or shock for proper grounding and, in particular, specifies that the cable hazard, do not expose the TV to rain or ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. moisture. Use of this television receiver for other than private viewing of
Краткое содержание страницы № 3
Table of Contents Table of Contents Setting the Video Inputs.................................. 29 Installing and Connecting the TV Operating Video Equipment with Your TV Unpacking .......................................................... 4 Remote Control .......................................... 30 Inserting Batteries into the Remote Control ... 4 Programming the remote control ............ 30 Preventing the TV from Falling Down ............ 4 Operating optional equipment ................. 32
Краткое содержание страницы № 4
Installing and Connecting the TV Installing and Preventing the TV from Falling Down Connecting the Attach the supplied bracket to the rear of the TV, and TV pass a sturdy cord or chain and attach it to a wall or pillar. Consult your dealer when attaching the bracket, since the screws for the bracket also hold the rear cabinet in a place. Unpacking 1 Remove one of the screws attached at the rear of When you unpack this unit, make sure there is all the the TV. following: Note Remote control (1) an
Краткое содержание страницы № 5
Installing and Connecting the TV 4 Attach a sturdy cord or chain securely to each Connector Types bracket on the rear of the TV. You may find it necessary to use some of the following connector types during set up. Attach the cord or chain (not supplied) Supplied 75-ohm coaxial cable securely. Screw-on type Screw into connection. S VIDEO cable High quality video cable for enhanced picture quality Align guides and push into connection. AUDIO/VIDEO cable Push into connection. 5 Attach the cord or
Краткое содержание страницы № 6
Installing and Connecting the TV Identifying Front and Rear Connectors TV front panel Under the panel Rear of TV VHF/UHF VIDEO IN 1 COMPONENT VIDEO IN 1 AUDIO OUT R AUDIO L VIDEO S VIDEO R AUDIO LYP PB R R L AC IN CONTROL IN S Y/G PB/B PR/R R AUDIO L HD VD OUT SUB WOOFER VIDEO IN 2 COMPONENT VIDEO IN 2 / RGB IN 6 (US)
Краткое содержание страницы № 7
Installing and Connecting the TV 1 Headphones jack Connects to your headphones. Basic Connections If your headphones do not match the jack, use a (Connecting Cable TV or suitable plug adaptor (not supplied). Antenna) 2 VIDEO IN 1, 2 (pages 8 - 10, 13) Connects to the output jacks of your VCR or other video equipment. Connecting directly to cable or an antenna 3 COMPONENT VIDEO IN 1 (pages 12, 14) Connects to the component video (Y, PB, PR) and audio (L/R) output jacks of your DVD player or VHF o
Краткое содержание страницы № 8
Installing and Connecting the TV Connecting a VCR and Cable Use this hookup if: • You have cable TV that does not require a cable box. Disconnect all power sources before making any connections. 1 Connect the cable TV cable to the VCR’s IN jack. 2 Using the supplied 75-ohm coaxial cable, connect the VCR’s OUT jack to the TV’s VHF/UHF jack. 3 Using AUDIO and S VIDEO cables, connect the VCR’s Audio and S Video OUT jacks to the TV’s AUDIO and S VIDEO IN jacks. Rear of TV VHF/UHF VIDEO IN 1 COMPONE
Краткое содержание страницы № 9
Installing and Connecting the TV Connecting a Satellite Receiver Disconnect all power sources before making any connections. 1 Connect the satellite antenna cable to the satellite receiver’s SATELLITE IN jack. 2 Using AUDIO and S VIDEO cables, connect the satellite receiver’s AUDIO and S VIDEO OUT jacks to the TV’s AUDIO and S VIDEO IN jacks. 3 Connect the supplied 75-ohm coaxial cable from your cable or antenna to the TV’s VHF/UHF jack. Rear of TV VHF/UHF VIDEO IN 1 COMPONENT VIDEO IN 1 AUDIO
Краткое содержание страницы № 10
Installing and Connecting the TV Connecting a Satellite Receiver with a VCR Disconnect all power sources before making any connections. 1 Connect the satellite antenna cable to the satellite receiver’s SATELLITE IN jack. 2 Connect the CATV cable to the VCR’s VHF/UHF IN jack. 3 Using the supplied 75-ohm coaxial cable, connect the VCR’s OUT jack to the TV’s VHF/UHF jack. 4 Using AUDIO and S VIDEO cables, connect the satellite receiver’s AUDIO and S VIDEO OUT jacks to the VCR’s AUDIO and S VIDEO IN
Краткое содержание страницы № 11
Installing and Connecting the TV Connecting an Audio Receiver Disconnect all power sources before making any connections. Using an AUDIO cable, connect the TV’s AUDIO OUT jacks to the audio receiver’s AUDIO IN jacks. Rear of TV VHF/UHF VIDEO IN 1 COMPONENT VIDEO IN 1 AUDIO OUT R L R AUDIO L VIDEO S VIDEO R AUDIO LYP PB R AC IN CONTROL S IN R AUDIO L Y/G PB/B PR/R HD VD OUT SUB VIDEO IN 2 COMPONENT VIDEO IN 2 / RGB IN WOOFER AUDIO-R (red) AUDIO-L (white) RK-74A (not supplied) Audio input Au
Краткое содержание страницы № 12
Installing and Connecting the TV Connecting a DVD Player with Component Video Connectors This is the preferred hookup to use if: • Your DVD player has component (Y, B-Y, R-Y) jacks. Disconnect all power sources before making any connections. 1 Using three separate component video cables, connect the DVD player’s Y, B-Y and R-Y jacks to the Y, PB and PR jacks on the TV. Use the COMPONENT VIDEO IN 1 connections. Tip The Y, B-Y and R-Y jacks on your DVD player are sometimes labeled Y, CB and CR, or
Краткое содержание страницы № 13
Installing and Connecting the TV Connecting a DVD Player with A/V Connectors Use this hookup if: • Your DVD player does not have component (Y, PB, PR) jacks. Tip If your DVD player has video component output connectors: for best picture quality use the connection described on page 12. Disconnect all power sources before making any connections. 1 Using an AUDIO cable, connect the DVD player’s AUDIO OUT jacks to the TV’s AUDIO IN jacks. 2 Using an S VIDEO cable, connect the DVD player’s S VIDEO j
Краткое содержание страницы № 14
Installing and Connecting the TV Connecting a Digital TV Receiver Disconnect all power sources before making any connections. 1 Using three separate component video cables, connect the Digital TV Set-top box’s Y, PB and PR jacks to the TV. Notes • The Y, PB and PR jacks do not provide audio, so audio cables must be connected to provide sound. • Component video (Y, PB, PR) connection is necessary to view 480i, 720p, and 1080i formats. Note that this TV displays all format types of picture in a re
Краткое содержание страницы № 15
Installing and Connecting the TV Connecting a Sub Woofer Disconnect all power sources before making any connections. Using a monaural audio cable, connect the TV’s SUB WOOFER jack to the sub woofer’s input jack. Rear of TV VHF/UHF VIDEO IN 1 COMPONENT VIDEO IN 1 AUDIO OUT R AUDIO L VIDEO S VIDEO YP PB R R L R AUDIO L AC IN CONTROL S IN R AUDIO L Y/G PB/B PR/R HD VD OUT SUB VIDEO IN 2 COMPONENT VIDEO IN 2 / RGB IN WOOFER SUB WOOFER Monaural audio cable Sub woofer input (not supplied) Sub wo
Краткое содержание страницы № 16
Installing and Connecting the TV Connecting an RGB Equipment Disconnect all power sources before making any connections. 1 Using an RGB cable, connect the RGB equipment’s video/synchronized signal output terminal to the Y/G, PB/B, PR/R, HD, and VD jacks on the TV. Use the COMPONENT VIDEO IN 2/RGB IN connections. 2 Using an AUDIO cable, connect the RGB equipment’s AUDIO OUT jacks to the TV’s AUDIO IN jacks. Be sure to use the same row of inputs that you used for the video connection (COMPONENT VI
Краткое содержание страницы № 17
Installing and Connecting the TV 1 Press Power on the front panel of your TV. The Setting the Channels Auto Setup menu appears. After you finish connecting your TV, you can run Auto Setup Auto Program to set up your channels. The Auto [ Auto Program: CH+ POWER Exit [ CH– Program screen appears when you turn your TV on , First please connect for the first time after installing it. c a bl e /antenna To change or skip channels, see page 19. Note The Auto Program feature does not apply for an instal
Краткое содержание страницы № 18
Installing and Connecting the TV To watch CATV channels To skip channels You have to subscribe to a cable TV company. Note You can skip unnecessary channels when selecting that cable TV cannot be received in some areas. This channels using the CH +/– buttons. TV receives 1-125 cable TV channels. For details on cable TV subscription, consult your nearest cable TV 1 Press MENU. company. 2 Press V/v to select (TV Setup), then press . 1 Press MENU. 3 Press V/v to select “Channel Skip/Add,” then 2 P
Краткое содержание страницы № 19
Installing and Connecting the TV 1 Press MENU. Selecting the On-screen Picture/Sound Control Picture Mode : Liv.Rm. Menu Language MENU Adjust P icture Adjust Sound , You can select the language to be displayed in all menu. ,, to select ENTER, to enter adj . menu 2 Press V/v to select (Initial Setup), then press . MUTING POWER VCR/DVD SAT/CABLE TV Ini t ial Setup L ang uage : Eng l i s h FUNCTION SYSTEM : Col o r Sy stem OFF VCR/DVD SAT/CABLE TV MENU Function : On /Of f , ENTER ,, to select, to
Краткое содержание страницы № 20
Watching the TV 1 Press POWER on the remote. Watching the TV POWER TV Tip When the STANDBY/SLEEP indicator goes off, press Watching the TV POWER on the TV. 2 Select the desired channel using the 0-9 and ENTER buttons. Press 0-9 to select a channel, the channel changes after 2 seconds. Press ENTER to select STANDBY/ immediately. SLEEP Use the CH +/– buttons to scan through the channels. CH 12 3 MUTING or MUTING POWER 45 6 VCR/DVD SAT/CABLE TV 1 78 9 ENTER FUNCTION SYSTEM OFF VCR/DVD SAT/CABLE TV
