Краткое содержание страницы № 1
CAD-05 Kit GSM
Auto Dialer
Owner’s Manual
CAD-05 Kit Manual.indd 1 10/15/2009 9:40:53 AM
Краткое содержание страницы № 2
Warnings: This device complies with Part 15 of the FCC rules, Operation of this device is subject to the fol- lowing conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference, including interference that may cause undesired operation. Features: Wireless alarm; no telephone line required, GSM Dialer supports any standard SIM card; program- mable entry/exit delay time; two separate dialer alarms, alarm and panic; select up to 9 (32 digit) user pro
Краткое содержание страницы № 3
IMPORTANT Before you install the PIR Detectors, please take these points into consideration: Don’t position the detectors facing windows. Don’t position in direct sunlight. Don’t position above heat sources or in areas of moisture. Don’t let pets roam into the detection area when the system is armed. The PIR Sensor is set to Alarm 2 so take this into account when you are programming your voice messages. Opening the PIR Sensor to access dipswitches and battery connector: 1. Slide the PIR Senso
Краткое содержание страницы № 4
Figure 1 Installation Tools: Small & Large Phillips Screwdrivers; Small Standard Screwdriver. Set Up: 1. Set PIR and CAD-05 dipswitches to match. The first five dipswitches on both units (Figure 1-1 and Figure 2-1) need to be set exactly the same with the last 3 dipswitches on the PIR sensor (Figure 1-1) 1 matching the 3 numbers on the sticker to the left of the dipswitches on the dialer (Figure 2-2). (Note: On the PIR sensor, “off” is in the down 2 position. On the Dialer, “off” is in the
Краткое содержание страницы № 5
Figure 3 SIM card is properly installed, you will see a telephone symbol on the display (Figure 4-2). You now have 30 seconds to teach the dialer. Press the RECORD button (Figure 4-3) on the dialer and the display will show “learning 0.” Press any key on the RF Keyfob. The display will then show “learning 1” followed by a BEEP to confirm that it has learned the first keyfob. You then have another 30 seconds to teach it another keyfob (“learning 2”) and so on up to 5 keyfobs. 5. (Note: Tam
Краткое содержание страницы № 6
Advanced Operations HOw TO PRO g RAM THe AUTO DIAle R *If no key is pressed for 30 seconds, the dialer will automatically exit the programming mode. Notice: The system must be in the OFF mode for all programming. How to record the voice messages: Alarm 1 = Tamper and panic alarm. Alarm 2 = PIR sensors and hard-wired input. 1. Key in the four digit user password code (factory default is 1234.) 2. Press RECORD. 3. Press 1 (to save as the message for alarm 1) or 2 (to save as the message for al
Краткое содержание страницы № 7
1. Key in the four digit user password code (factory default is 1234.) 2. Press PROGRAM > 3 > ENTER. 3. The number you press next will select the position in the sequence you want that telephone number to dial (1 = first number called, 2 = second number called, and so on). 4. Press ENTER and key in the first telephone number. 5. Press ENTER to exit the programming mode. 6. Repeat the process until you have entered all the numbers you wish the Auto Dialer to call once it has been activate
Краткое содержание страницы № 8
How to change the user password code (factory default is 1234): 1. Key in the four digit user password code (factory default 1234.) 2. Press PASSWORD 3. The LCD will change to n-p. 4. Key in your new four digit user password code. 5. The LCD will change to c-p. 6. Key in your new four digit user password code again. 7. The LCD will change to acc. Quick guide: Press 1 2 3 4 > PASSWORD > New Code > Confirm New Code How to program the Auto Dialer to give an audible alarm as well as sending
Краткое содержание страницы № 9
How to set entry/exit Delay times (default both delay set at 30 seconds): The entry/exit times are the times the Auto Dialer gives you to enter/exit the area covered by the system before it arms/alarms. These are pre-set to 30 seconds. You can also change the timing to instant or 60 seconds. Entry Delay: 1. Key in the four digit user password code (factory default 1234.) 2. Press PROGRAM > 4 > ENTER 3. Press N (N = 0 for instant; 3 for 30 seconds; 6 for 60 seconds). Press ENTER. Quick guid
Краткое содержание страницы № 10
How to disable Tamper Function (factory setting Tamper ON): 1. Key in the four digit user password code (factory default 1234.) 2. Press PROGRAM > 8 > ENTER 3. Press N (N = 0 without tamper function; 1 with tamper function). Press ENTER. Quick guide: Press 1 2 3 4 > PROGRAM > 8 > ENTER > N > ENTER HOw TO OP eRATe THe AUTO DIAle R How to Arm the Alarm System/Turn the Dialer ON: 1. Check that the voice message and at least one phone number has been programmed into the Auto Dialer. 2. Press
Краткое содержание страницы № 11
How to stop the Dialer from dialing the telephone numbers in sequence: When the Auto Dialer starts dialing, it will dial the first telephone number and repeat the pre-recorded voice message for 1 minute. If there is no response from the phone, then it will hang up and dial the next number until all the programmed numbers for that alarm are dialed. It will repeat this dial sequence three times and display ‘NO ANSWER’ if there is no response from any of the phone numbers. To stop this dial seq
Краткое содержание страницы № 12
How to change the back-up battery: Important: It is recommended to change the back-up battery at least once a year, even if the battery is not low. 1. First make sure that the Auto Dialer is OFF. Then release it from the wall. 2. Remove the battery door and take out the old battery. Insert new 7.2V rechargeable battery pack and make sure it is in the correct polarity. 3. Fit the battery door and mount the Auto Dialer back onto the wall. IMPORTANT: SIM Card Most pay-as-you-go SIM cards will
Краткое содержание страницы № 13
HOw TO R eSeT THe AUTO DIAle R Inside the battery compartment: Remove the power supply and the Auto Dialer from the wall. Remove the 7.2V battery. Then remove the SIM card. Inside the battery compartment is a switch. Move it to the ERASE position. Connect the power to the Auto Dialer then press DELETE twice. There will be 2 short beeps from the Auto Dialer. Switch the power off again. Replace the SIM card, place switch back to NORMAL. Replace the 7.2V battery and place back onto the wall. Po
Краткое содержание страницы № 14
CAD-05 Quick Reference Programming (For step-by-step programming, refer to pages 6-10) Programming: Enter Pass code 1234; push the Program button; select option number; 1 - Audible Alarm (N = 1-Audible; 0-Silent) 1234>PROGRAM>1>ENTER>N>ENTER 2 - Length of Audible Alarm (N = 1-99 Mins) 1234>PROGRAM>2>ENTER>N>ENTER 3 - Add Numbers (N = 1-9 order in which numbers are dialed) 1234>PROGRAM>3>ENTER>N>ENTER>PHONE NUMBER>ENTER Delete Numbers (N = 1-9 order in which numbers are dialed)
Краткое содержание страницы № 15
TECHNICAL SUPPORT If you encounter any difficulty in the operation of this product after reading the manual, please contact us. You can reach us by phone at 605-356-2772 from 8:30 AM to 5:00 PM Monday through Friday (Central Standard Time). We will be happy to answer your questions and help you in any way we can. WARRANTY Dakota Alert warrants this product to be free of defects in material and workmanship for a period of one year from the date of purchase. This warranty does not cover damage
Краткое содержание страницы № 16
Dakota Alert, Inc. Phone: (605) 356-2772 32556 E. Main Street Fax: (605) 356-3662 P0 Box 130 Web: www.dakotaalert.com Elk Point, SD 57025 CAD-05 Kit Manual.indd 16 10/15/2009 9:40:53 AM
