Руководство по эксплуатации InFocus DV 20VB2

Краткое содержание страницы № 1

Impact Drill
Model DV 20VB2
Handling instructions
Note:
Before using this Electric Power Tool, carefully read through these
HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is
recommended that these INSTRUCTIONS be kept readily available
as an important reference when using this power tool.

Краткое содержание страницы № 2

17. Avoid unintentional starting. Do not carry a plugged- GENERAL OPERATIONAL PRECAUTIONS in tool with a finger on the switch. Ensure switch is off when plugging in. WARNING! When using electric tools, basic safety 18. Use outdoor extension leads. When tool is used precautions should always be followed to reduce the outdoors, use only extension cords intended for risk of fire, electric shock and personal injury, including outdoor use. the following. 19. Stay alert. Watch what you are doing. Use

Краткое содержание страницы № 3

SPECIFICATIONS Voltage (by areas)* (110V, 220V, 230V, 240V) Power input 730 W* Speed change 1 2 –1 –1 No load speed 0 – 1000 min 0 – 3000 min Steel 13 mm 8 mm Capacity Concrete 20 mm 13 mm Wood 40 mm 25 mm –1 –1 Full load impact rate 8000 min 26000 min Weight (without cord) 2.2 kg *Be sure to check the nameplate on product as it is subject to change by areas. 5. Mounting and dismounting of the bit. STANDARD ACCESSORIES For keyed chuck (Fig. 2) (1) Chuck Wrench (Spec. only for keyed chuck) .....

Краткое содержание страницы № 4

NOTE 7. Fixing the side handle (Fig. 7) When the sleeve does not become loose any further, Attach the side handle to the mounting part. fix the side handle to ring, hold side handle firmly, Rotate the side handle grip in a clockwise direction then turn the sleeve to loosen by hand. (Fig. 4) to secure it. Set the side handle to a position that is suited to the Ring operation and then securely tighten the side handle grip. Loosen Sleeve Side handle Side handle Loosen Tighten Fig. 4
Type B (Fig.

Краткое содержание страницы № 5

Change lever Stopper Speed control dial Low speed High speed Impact Rotation Switch trigger Fig. 9 Fig. 11 9. High-speed/Low-speed changeover: 2. Drilling Prior to changing speed, ensure that the switch is in
When drilling, start the drill slowly, and gradually the OFF position, and the drill has come to a complete increasing speed as you drill. stop.
Always apply pressure in a straight line with the bit. To change speed, rotate the gear shift dial as indicated Use enough pressure to keep

Краткое содержание страницы № 6

6. Service parts list CAUTION: Repair, modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed. MODIFICATION: Hitachi Power Tools are constantly being improved and modifi

Краткое содержание страницы № 7

7 Item Code No. Item Code No. Remarks Remarks No. No. Used No. No. Used 1 995-344 1 M6×25 36 1 340-587C 1 110V ____ 2 1 36 2 340-587E 1 230V 3 1 321-814 1 13VLRB-D 36 3 340-587F 1 240V 3 2 319-546 1 13VLRE-N 37 608-VVM 1 608VVC2PS2L 3 3 316-280 1 13VLN 38 322-861 1 ____ 4 1 322-857 1 39 1 4 2 322-866 1 40 301-653 3 D4×20 5 939-556 1 41 322-862 1 6 322-851 1 42 322-853 1 7 620-2DD 1 6202DDCMPS2L 43 322-854 1 8 322-850 1 44 321-630 1 100L 9 984-101 1 45 1 322-517 1 220V-240V 10 959-150 1 D6.35 45

Краткое содержание страницы № 8

Hitachi Koki Co., Ltd. 601 Code No. C99145011 Printed in Ireland