Краткое содержание страницы № 17
(2) Where the Saved Data Call Command is used: Power ON [ESC] XQ: Calls the label format stored in the flash Place paper memory board. Saved Data Call Command Feed Command [ESC] T: Feeds one sheet of paper and aligns it with the first printing position. [ESC] RC: Draws bit map font data. Bit Map Font Data Command [ESC] RV: Draws outline font data. Outline Font Data Command [ESC] RB: Draws bar code data. Bar Code Data Command [ESC] XS: Issues (prints) the la
Краткое содержание страницы № 18
6. INTERFACE COMMANDS 6.1 OUTLINE OF COMMANDS (1) Format of Interface command ESC Command & Data LF NUL z The length from [ESC] to [LF] [NUL] must be as specified by each command. z There are the following three kinds of control codes: c ESC (1BH), LF (0AH), NUL (00H) d { (7BH), | (7CH), } (7DH) (2) How to use reference Function Describes the outline of the function of the command. Format Shows the format of the command. The format designation method should con
Краткое содержание страницы № 19
NOTES: 1. If a command is not recognized as a command, it is ignored. e.g.) [ESC] H, [ESC]AA, and so on. 2. If the number of digits of the parameter is specified, when the number of in put digits does not match the specified number of digits, a command error occurs. 3. When a parameter is set to any character/value other than specified characters/values, a command error occurs. e.g.) In the case that a value should be set for parameter, “0001” is acceptable, however, “000A” results in an
Краткое содержание страницы № 20
6.2 LIST OF COMMANDS (1) Commands related to setting Label Size Set Command [ESC] D......................................17 (2) Commands related to fine adjustment Position Fine Adjust Command [ESC] AX....................................22 Print Density Fine Adjust Command [ESC] AY....................................27 (3) Commands related to clear Image Buffer Clear Command [ESC] C......................................28 Clear Area Command [ESC] XR ............................
Краткое содержание страницы № 1
TOSHIBA TEC Bar Code Printer
B-SV4D-GS/GC10-QM
External Equipment Interface Specification
First Edition: Jun. 02, 2003
Краткое содержание страницы № 2
TABLE OF CONTENTS Page 1. SCOPE........................................................................................................................................ 1 2. GENERAL DESCRIPTION......................................................................................................... 1 3. INTERFACE................................................................................................................................ 2 3.1 SERIAL INTERFACE............................
Краткое содержание страницы № 3
Page 6.3.21 GRAPHIC COMMAND..................................................................................................... 146 6.3.22 SAVE START COMMAND ............................................................................................... 154 6.3.23 SAVE TERMINATE COMMAND ...................................................................................... 156 6.3.24 SAVED DATA CALL COMMAND.....................................................................................
Краткое содержание страницы № 4
Page 11. CHARACTER CODE TABLE ..................................................................................................... 183 11.1 TIMES ROMAN, HELVETICA, LETTER GOTHIC, PRESTIGE ELITE, COURIER............... 183 11.2 PRESENTATION................................................................................................................... 190 11.3 TEC OUTLINE FONT 1 ......................................................................................................... 194 1
Краткое содержание страницы № 5
1. SCOPE This specification applies to the external equipment interface for use with the Model B-SV4D general- purpose thermal label/tag printers. 2. GENERAL DESCRIPTION The external equipment interface connects a printer to the host computer through a serial interface (RS- 232C), parallel interface (Centronics), or a network for making various settings and printing labels. This specification describes how to use the external equipment interface. The model configuration is described below
Краткое содержание страницы № 6
3. INTERFACE 3.1 SERIAL INTERFACE (1) Type : Conforming to RS-232C (2) Mode of Communication : Full duplex (3) Transmission Speed : 2400 BPS 4800 BPS 9600 BPS 19200 BPS 38400 BPS 57600 BPS (4) Synchronization Method : Start-stop synchronization (5) Start Bit : 1 bit (6) Stop Bit : 1 bit 2 bits (7) Data Length : 7 bits 8 bits (8) Parity : None Even Odd (9) Error Detection : Parity Error Vertical parity error check Framing Error This error occurs if no
Краткое содержание страницы № 7
(13) Transmission Control : XON/XOFF (DC1/DC3) Protocol READY/BUSY (DTR) Protocol XON/XOFF (DC1/DC3) Protocol + READY/BUSY (DTR) Protocol RTS Protocol c XON/XOFF (DC1/DC3) Protocol z When initialized after power on, this printer becomes ready to receive data and sends an XON code (11H). (Transmission or non-transmission of the XON code is selectable by means of the parameter setting.) z The printer sends an XOFF code (13H) when the blank positions in the receive buffer
Краткое содержание страницы № 8
e XON/XOFF (DC1/DC3) Protocol + READY/BUSY (DTR) Protocol z When initialized after power on, this printer becomes ready to receive data and turns the DTR signal to “High” level (READY). The printer also sends an XON code (11H). z When the blank positions in the receive buffer are 1K bytes or less, the printer turns the DTR signal to “Low” level (BUSY) and sends an XOFF code (13H). z When the blank positions in the receive buffer are 2K bytes or more, the printer turns the DTR signa
Краткое содержание страницы № 9
(14) RS-232 Interface pin configuration Host Function 9 Pin 25 Pin 9 Pin Printer Function 1 +5V RxD 2 3 2 TxD TxD 3 2 3 RxD DTR 4 20 4 DSR GND 5 7 5 GND DSR 6 6 6 RDY RTS 7 4 7 N/C CTS 8 5 8 RDY 9 +5V (15) Connector Pin Assignment and Signal Description Signal Pin No. Function Signal Direction Name 1 +5V Provide the power of 5V 2 TxD Transmit data Printer → 3 RxD Receive data ← Host 4 DSR Data set ready ← Host 5 GND General Ground 6 RDY Printer
Краткое содержание страницы № 10
3.2 PARALLEL INTERFACE (1) Type : Centronics (2) Mode : Conforms to IEEE1284 compatible mode (3) Data Input Method : Parallel 8 bits (DATA1 ~ 8) (4) Control Signals : ACK, BUSY, SELECT, DATA • STB, FAULT, PE, INIT (Not used), AUTOFD (Not used), SELECTIN (Not used) (5) Data Input Code : ASCII code European character set 8 bit code Graphics 8 bit code (6) Receive Buffer : 515K bytes (7) Connector : Printer Amp. Japan 552742-1 or equivalent DDK 57RE-40360-73B or equivalent
Краткое содержание страницы № 11
(8) Connector Pin Diagram: Pin No. Signal Name Pin No. Signal Name 1 DATA • STB 19 TWISTED PAIR GND (PIN1) 2 DATA 1 20 TWISTED PAIR GND (PIN2) 3 DATA 2 21 TWISTED PAIR GND (PIN3) 4 DATA 3 22 TWISTED PAIR GND (PIN4) 5 DATA 4 23 TWISTED PAIR GND (PIN5) 6 DATA 5 24 TWISTED PAIR GND (PIN6) 7 DATA 6 25 TWISTED PAIR GND (PIN7) 8 DATA 7 26 TWISTED PAIR GND (PIN8) 9 DATA 8 27 TWISTED PAIR GND (PIN9) 10 ACK 28 TWISTED PAIR GND (PIN10) 11 BUSY 29 TWISTED PAIR GND (PIN11) 12 PE 30 TWISTED PAIR
Краткое содержание страницы № 12
4. KEY OPERATION FUNCTIONS 4.1 SYSTEM MODE (POWER UP WITH KEY PRESSED) There are 6 LED light indications with following sequence. (1) Solid orange indicates the printer has entered into system mode (2) Green and red alternate (3) Flashing orange (4) Green and orange alternate (5) Orange and red alternate (6) Solid green 4.1.1 Firmware downloading mode 1) Release FEED key at LED light sequence (2) and push again immediately. 2) Copy the firmware file to printer parallel port by the f
Краткое содержание страницы № 13
[Self-test printing] a. Printing program version & check sum b. Printing various parameters Parameter Initial value Print density fine adjustment 0 Print position fine adjustment 0 mm Amount for finely the cut position 0 mm Type of character code PC-850 Font of zero 0 (without slash) Communication speed 9600 bps Data length 8 bits Stop bit length 1 bit Parity NONE Transmission control 2 Forward feed wait ON Control code AUTO Feed key function FEED Euro code B0 H X-coordinate a
Краткое содержание страницы № 14
5. TRANSMISSION SEQUENCE This section describes the outline of the transmission sequence. 5.1 INITIALIZATION Writable characters, logo, and PC interface commands must be stored before the label issue operation. (1) Storing writable characters and logo Power ON No Yes (Add/change) [ESC] J1: Formats the flash memory on the Memory board memory board. Format Command [ESC] XD: Stores writable characters or a Bit Map Writable logo on the flash memory board.
Краткое содержание страницы № 15
(2) Storing PC interface commands Power ON No Yes (Add/change) [ESC] J1: Formats the flash memory board. Memory board Format Command [ESC] XO: Declares the start of saving PC interface Save Start Command commands. [ESC] D: Sets the label size. Label Size Set Command [ESC] AX: Adjusts the feed length, cut position, and Position Fine Adjust Command back feed length. Print Density Fine [ESC] AY: Adjusts the print density. Adjust Command [E
Краткое содержание страницы № 16
5.2 LABEL ISSUE OPERATION An example of the label issue operation is described below. (1) Where the Saved Data Call Command is not used: Power ON Place paper [ESC] D: Sets the label size. Label Size Set Command [ESC] AX: Adjusts the feed length, cut position, and Position Fine back feed length. Adjust Command Print Density Fine [ESC] AY: Adjusts the print density. Adjust Command [ESC] T: Feeds one sheet of paper and aligns it Feed Command with the first printi
