Руководство по эксплуатации Fisher-Price C1454

Краткое содержание страницы № 1

C1454
Instructions
Please keep this instruction sheet for future reference, as it contains important information.
Requires three “C” batteries (included).
Adult assembly is required.
Tool required for assembly: Phillips screwdriver (not included).
™
Kick & Whirl Carnival
1
w
w
w.
fi
s
he
r
-p
r
i
c
e
.
c
o
m

Краткое содержание страницы № 2

Parts CAUTION This product contains small parts in its unassembled state. Adult assembly is required. WARNING To prevent entanglement injury, never place this toy in a crib or playpen. Never add strings, ties or other products to this toy. 2 Tracks Base Door Ferris Wheel Assembly 2 Ramps Base Base Support 3 Spinning Toys 5 Balls 2 Ramp Covers 1 #8 x /2" Screw – 24 #8 x 2" Shoulder Screw – 2 FASTENERS SHOWN ACTUAL SIZE Note: Tighten and loosen all screws with a Phillips Screwdriver. Do not over-

Краткое содержание страницы № 3

Battery Replacement Battery Safety Information Batteries may leak fluids that can cause a chemical burn injury or ruin your toy. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). 1.5V x 3 •Insert batteries as indicated inside the battery compartment. "C" (LR14) • Remove batteries during long periods of non-use. Always remove exhausted batteries from the toy. Dispose of batteries safely.

Краткое содержание страницы № 4

Assembly Track Track Base Base Support 1 4 • Insert a track into one side of the base as shown. •Insert and “snap” the base support into the base. • Insert the other track into the opposite side of the base. 1 1 #8 x /2" Screw #8 x /2" Screw Ramp Cover 2 Bottom View Ramp •Turn the assembly over so the bottom of the base is facing you. 5 1 • Insert four #8 x /2" screws through the base and into the tracks. • Fit a ramp cover onto a ramp as shown. Tighten the screws. 1 •Insert two #8 x /2" screws

Краткое содержание страницы № 5

Assembly Ramp #8 x 2" Shoulder Screw Ferris Wheel Ferris Wheel Assembly 1 #8 x /2" Screw 7 •Position the Ferris wheel assembly so that the back is facing you. •Fit one of the ramps on the back of the Ferris wheel assembly as shown. 1 • Insert four #8 x /2" screws through the ramp and into the Ferris wheel assembly. Tighten the screws. •Repeat this procedure to attach the other ramp to the Ferris wheel. Hub Ferris Wheel 9 Ramp • Rotate the Ferris wheel down toward the base. The arch should “click

Краткое содержание страницы № 6

Kick-Activated Gym •To convert to a Kick-Activated Gym, pull up on the center clamp under the Ferris wheel to “snap” the arch into position. • Snap the balls onto the pegs on the Ferris wheel. • Snap the spinning toys into the clamps under the Ferris wheel. •Slide the mode switch to the I position. •Slide the volume switch on the back of the Ferris wheel to either low volume or high volume . • Baby can kick the base or bat at the toys for about five minutes of fun music, sound effects and color

Краткое содержание страницы № 7

Sit-Up Fun •To convert to Sit-Up Fun, press the button near each ramp cover at the same time, push the Ferris wheel down until it “clicks” into position. •“Pop” the colorful balls off the pegs on the Ferris wheel. • Fit the spinning toys onto the pegs in the ramp covers or on the track. • Open the base door. •Slide the mode switch to the II position. •Slide the volume switch on the back of the Ferris wheel to either low volume or high volume . • Drop the colorful balls through the openings in t

Краткое содержание страницы № 8

Consumer Information Questions? We’d like to hear from you! Care ® Call Fisher-Price Consumer Relations, toll-free at 1-800-432-5437, •Wipe this toy with a clean damp cloth dampened with a mild soap and 8 AM - 6 PM EST Monday through Friday. Hearing-impaired water solution. consumers using TTY/TDD equipment, please call 1-800-382-7470. • Do not immerse this toy. Or, write to: ® Fisher-Price Consumer Relations FCC Statement (United States Only) 636 Girard Avenue Note: This equipment has been te