Краткое содержание страницы № 1
Dell Latitude E5430
Owner's Manual
Regulatory Model: P27G
Regulatory Type: P27G001
Краткое содержание страницы № 2
Contents Notes, Cautions, and Warnings.............................................................................................. 0 1 Working on Your Computer.......................................................................................................5 Before Working Inside Your Computer.....................................................................................................................5 Turning Off Your Computer.......................................................
Краткое содержание страницы № 3
Installing the Memory Module................................................................................................................................22 Removing the Right Base Panel..............................................................................................................................23 Installing the Right Base Panel...............................................................................................................................23 Removing the Thermal M
Краткое содержание страницы № 4
Docking Port Information........................................................................................................................................57 5 System Setup.............................................................................................................................59 Overview ................................................................................................................................................................59 Entering System Setup..
Краткое содержание страницы № 5
Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have read the safety information that shipped with your computer. • A component can be replaced or--if purchased separately--installed by performing the removal procedure in reverse order.
Краткое содержание страницы № 6
Turning Off Your Computer CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer. 1. Shut down the operating system: – In Windows 7: Click Start , then click Shut Down. – In Windows Vista: Click Start , then click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut Down. – In Windows XP: Click Start → Turn Off Computer → Turn Off . The computer turns off after the operating system shutdown
Краткое содержание страницы № 7
Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may require the following tools: • Small flat-blade screwdriver • Phillips screwdriver • Small plastic scribe Removing the SD Memory Card 1. Follow the procedures in Before Working Inside Your Computer. 2. Press in on the SD memory card to release it from the computer. 3. Slide the SD memory card out of the
Краткое содержание страницы № 8
3. Remove the battery from the computer. Installing the Battery 1. Slide the battery into its slot until it clicks into place. 2. Follow the procedures in After Working Inside Your Computer. Removing the Subscriber Identity Module (SIM) Card 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Press and release the SIM card located on the battery wall. 4. Slide the SIM card from the computer. 8
Краткое содержание страницы № 9
Installing the Subscriber Identity Module (SIM) Card 1. Insert the subscriber identity module (SIM) card into the slot. 2. Install the battery. 3. Follow the procedures in After Working Inside Your Computer. Removing the Display Bezel 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery. 3. Pry up the bottom edge of the display bezel. 4. Work your way around the sides and top edge of the display bezel. . 5. Remove the display bezel from the computer . Installing
Краткое содержание страницы № 10
3. Install the battery. 4. Follow the procedures in After Working Inside Your Computer. Removing the Camera 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove: a) battery b) display bezel 3. Disconnect the camera cable. 4. Remove the screw that secures the camera and microphone module. 5. Lift and remove the camera and microphone module. Installing the Camera 1. Place the camera and microphone module in position on the display bezel. 2. Tighten the screw that secures the
Краткое содержание страницы № 11
4. Flip the display panel over. 5. Lift the mylar tape and disconnect the low-voltage differential signalling (LVDS) cable from the back of the display panel. 11
Краткое содержание страницы № 12
6. Remove the display panel from the display assembly. Installing the Display Panel 1. Install the screws that secure the display brackets to the display panel. 2. Attach the display panel to the display assembly. 3. Align the display panel in its original position in the computer. 4. Connect the low-voltage differential signaling (LVDS) cable to the display panel and attach the tape. 5. Flip the display panel over and install the screws that secure the display panel. 6. Install: a) display beze
Краткое содержание страницы № 13
4. Pry up the keyboard trim starting from the bottom edge. 5. Work your way around the sides and the top edge of the keyboard trim. 6. Lift upwards and remove the keyboard trim from the computer. 13
Краткое содержание страницы № 14
Installing the Keyboard Trim 1. Align the keyboard trim to its compartment. 2. Press along the sides of the keyboard trim until it snaps in place. 3. Install the battery. 4. Follow the procedures in After Working Inside Your Computer. Removing the Keyboard 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove: a) battery b) keyboard trim 3. Remove the screws at the back of the computer. 14
Краткое содержание страницы № 15
4. Remove the screws that secure the keyboard in place. 5. Lift the clip to release the keyboard cable and disconnect it from the computer . 6. Flip the keyboard over. 7. Peel off the adhesive tape securing the keyboard flat flex cable to the back of the keyboard and remove it from the computer. 15
Краткое содержание страницы № 16
8. Remove the keyboard from the computer . Installing the Keyboard 1. Attach the keyboard flat flex cable to the keyboard. 2. Affix the adhesive tape securing the keyboard flat flex cable to the keyboard. 3. Slide the keyboard into its compartment until all the metal tabs fit into their positions. 4. Fasten the keyboard cable clip. 5. Press down on the keyboard to the left and right side ensuring that all the snaps are fully engaged with the computer. 6. Install the screws that secure the keybo
Краткое содержание страницы № 17
4. Slide the access panel towards the front of the system and remove it from the computer. Installing the Access Panel 1. Slide the access panel into its slot until it clicks into place. 2. Install the screws that secure the access panel to the computer. 3. Install the battery. 4. Follow the procedures in After Working Inside Your Computer. Removing the Optical Drive 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove: a) battery b) access panel 17
Краткое содержание страницы № 18
3. Remove the screw that secures the optical drive. 4. Push the screw tab away from the computer to release the optical drive from the drive bay. 5. Remove the optical drive from the computer. 18
Краткое содержание страницы № 19
6. Remove the screws that secure the optical drive bracket. 7. Remove the optical drive bracket. 8. Disengage the optical drive bezel tabs to separate the optical drive bezel from the optical drive. 9. Remove the optical drive bezel. Installing the Optical Drive 1. Engage the optical drive bezel tabs to attach the optical drive bezel to the optical drive. 2. Install the optical drive bracket. 3. Tighten the screws that secure the optical drive bracket. 4. Insert the optical drive into the comput
Краткое содержание страницы № 20
3. Remove the screws that secure the hard drive bracket in place. 4. Use the tab to pull the hard drive bracket to release the hard drive from its connector. 5. Remove the hard drive from the computer. 20
