Краткое содержание страницы № 1
To The Owner • Carton Contents • Assembly • Parts Lists • Warranty
OPERATOR’S MANUAL
Twin Rear Bagger Kit
For i1000 Series Lawn Tractors
with a 42” Timed Deck
Model 19A70001000
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
FORM NO. 769-03805A
PRINTED IN U.S.A. CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 4/10/2008
Краткое содержание страницы № 2
This Operator’s Manual is an important part of your new grass collector. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says. Finding and Recording Model Number BEFORE YOU START ASSEMBLING YOUR NEW EQUIPMENT, please locate the model plate and copy the information from it in this Operator’s Manual for future reference. The information on the model plate is very important if you need help from our Customer Support Department or
Краткое содержание страницы № 3
NOTES Use this page to make notes and write down important information. 3
Краткое содержание страницы № 4
CONTENTS OF CARTON Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents are listed below and shown in Figure 2-1. 2 One Chute Tube Two Mounting Brackets One Discharge Chute Assembly One Cross-Support Bracket Carton Two Grass Bag Assemblies Two Bracket Supports One Support Tube One Catcher Support Contents One Grass Catcher Cover Assembly Chute Tube Discharge Chute Assembly If you are missing any parts, call the Customer Dea
Краткое содержание страницы № 5
CONTENTS OF HARDWARE PACK This grass collector kit is shipped with a hardware pack enclosed. Please check your hardware pack against the illustration below. 2 Carton Group A Assembling and Attaching Mounting Bracket Contents Clevis Pin (1) Hex Bolt 5/16-18 x .750 (6) If you are missing any parts, call the Cus- tomer Dealer Referral Hairpin Clip (1) Flange Lock Nut Line at 1-877-282-8684, 5/16-18 (6) or visit www.cubcadet.com to find the nearest Cub Cadet service dealer in your area. H
Краткое содержание страницы № 6
Assembling and Attaching The Bracket Assembly (Hardware Group A) 3 IMPORTANT: Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop the Assembling tractor engine and set the parking brake. and 1. Assemble the mounting bracket assembly as shown in Figure 3-1. Attaching NOTE: The mounting bracket assembly may have been preassembled at the factory, if this is the case, skip Step Mounting 1 and proceed to Step 2. Bracket 2. For convenience, pivot the seat
Краткое содержание страницы № 7
Attaching Grass Bags & Grass Bag Cover 1. Place the support tube in position on the rear of unit 4 by sliding the support tube down through the holes in the left side of the bracket assembly. Use the inside hole on the bracket assembly. Refer to Figure 4-1. Attaching 2. Attach the grass bags by hooking them onto the grass Grass Bags bag bracket using the slots in the grass bag and the tabs on the grass bag bracket as shown in Figure 4-2. & Grass Bag 3. Remove the clevis pins, belleville
Краткое содержание страницы № 8
Attaching Discharge Chute A 1. Lower the deck to its lowest position. 2. Raise the chute deflector on the deck (A) and hold it 5 while you position the discharge chute over the chute B opening. See Fig. 5-1. 3. Insert the pin (B) on the discharge chute into the hole Attaching on the deck as indicated by the arrow in Fig. 5-1. Discharge 4. Push down on the discharge chute so that it covers C the opening of the deck completely. Chute 5. Lock the discharge chute in position by stretching t
Краткое содержание страницы № 9
6 NOTES Use this page to take notes and write down important information. 9
Краткое содержание страницы № 10
4 18 11 12 2 16 14 19 17 12 14 8 17 20 13 1 21 7 30 32 14 20 14 9 20 7 28 29 26 13 17 31 24 27 14 25 13 23 10 22 9 6 3 15 10
Краткое содержание страницы № 11
F A C E T N O I R U Y REF PART DESCRIPTION 8 NO. NUMBER 1 16587D Bracket Support Illustrated 2 16592 Support Tube Assembly Parts List 3 764-0221 Catcher Bag 4 664-04017 Grass catcher Cover Assembly 5 683-04348 Mounting Bracket - RH 6 683-04350 Mounting Bracket - LH 7 710-0597 Screw 1/4-20 x 1” 8 710-0751 Hex Screw 1/4-20 x0.620 9 710-3008 Hex Screw 5/16-18 x 0.75” 10 711-0309A Clevis Pin 11 711-04069 Grass catcher Pin 12 711-1421 Clevis Pin 13 712-04063 Flange Lock Nut, 5/16-18 14 712-0406
Краткое содержание страницы № 12
CUB CADET LLC MANUFACTURER’S LIMITED WARRANTY FOR SEPARATELY SOLD ATTACHMENTS AND ACCESSORIES IMPORTANT: To obtain warranty coverage owner may be required a. Routine maintenance items such as lubricants, filters, blade to present an original proof of purchase and applicable maintenance sharpening, tune-ups, brake adjustments, clutch adjustments, deck records to the servicing dealer. Please see the operator’s manual for adjustments, and normal deterioration of the exterior finish due to infor
