Краткое содержание страницы № 1
OPERATOR’S MANUAL OPERATOR’S MANUAL
OPERATOR’S MANUAL
OPERATOR’S MANUAL OPERATOR’S MANUAL
MODEL GC-STT-CSV
THIS MANUAL CONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMA-
TION FOR YOUR SCAG ACCESSORY. READ-
ING THIS MANUAL WILL PROVIDE YOU
WITH MAINTENANCE AND ADJUSTMENT
PROCEDURES TO KEEP YOUR ACCESSORY
PERFORMING TO MAXIMUM EFFICIENCY.
THE SPECIFIC MODELS THAT THIS BOOK
COVERS ARE CONTAINED ON THE INSIDE
COVER. BEFORE OPERATING YOUR MA-
CHINE, PLEASE READ ALL THE INFORMA-
TION ENCLOSED
Краткое содержание страницы № 2
WARNING FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a complete halt before cleaning. * Keep hands, feet and clothing away from power-driven parts. * Read this manual completely as well as the Operator's Manual that came with your
Краткое содержание страницы № 3
A replacement manual is available from your 1.1 INTRODUCTION authorized Scag Service Dealer or by contacting: Scag Power Equipment, Service Department at P.O. This manual has been prepared to provide the Box 152, Mayville, WI 53050. You may also contact information you need to correctly assemble, operate, us through our website at www.scag.com The and maintain this grass catcher. Read it carefully and manual for this grass catcher can be downloaded by keep it for future reference. using the m
Краткое содержание страницы № 4
5. To clean the hopper debris screen; 3. When dumping the hopper into a disposal area: A. Disengage the deck drive and allow all W WARNING ARNING moving parts to come to a complete stop. DO NOT DUMP CLIPPINGS IN A DISPOSAL AREA THAT IS BURNING B. Apply parking brake and shut off the engine. A. Disengage the deck drive, apply the parking C. Stand on the left side of the hopper brake and allow all moving parts to come to assembly. a complete stop. D. Unhook the debris screen latches and B. Pu
Краткое содержание страницы № 5
3.1 ASSEMBLY INSTRUCTIONS 3. Remove the right side belt cover to gain access to the spindle assembly. Remove the u-nuts -NOTE- from the cutter deck bracket. See Figure 3-1. Use the illustrated parts list as a part number reference when following the assembly 4. Install the grass catcher pulley onto the spindle instructions. assembly. Apply loctite to both pulley setscrews and tighten. See Figure 3-1. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly 5
Краткое содержание страницы № 6
52" Cutter Deck LIFT LINK BELL CRANK SPACER NUT BOLT, 3/8-16 x 1-1/4" BOLT, 3/8-16 x 1-1/2" WASHER SPACER NUT CUTTER DECK REAR OF CUTTER DECK FRONT OF DISCHARGE CHUTE OPENING CUTTER DECK VIEW FROM RIGHT SIDE Figure 2-52"GC-STT install art OF CUTTER DECK 61" & 72" Cutter Decks P R O P E R Y L S E C R E V I E N N G E I W T H I O L I REAR OF A N D CUTTER DECK FRONT OF DISCHARGE CHUTE OPENING F U E L . CUTTER DECK VIEW FROM RIGHT SIDE OF CUTTER DECK Figure 2-61"GC-STT install art FIGURE 3-3
Краткое содержание страницы № 7
11. Install the belt to the spindle pulley. When 8. Install the blower assembly to the mounting replacing the belt, see figure below. bracket and secure with the mounting pin and hair pin. See Figure 3-4. BACK SIDE BLOWER IDLER PULLEY PULLEY 9. Align the blower assembly with the discharge opening of the cutter deck. Tighten the hardware for the mounting bracket. Install the quick pin through the rear hole in the discharge chute mounting bracket. See Figure 3-4. 10. Install the new belt cov
Краткое содержание страницы № 8
13. Install the hopper mounting brackets (p/n 451512 17. Install the weight support bar to the front of the & p/n 451595) to the outside of the frame on the machine by resting it directly on top of the caster rear of the machine using 3/8-16 x 1" hex head support arms and sliding it tight against the frame bolts (p/n 04001-19) and 3/8-16 elastic stop nuts of the machine. Secure the weight bar to the (p/n 04021-09). See Figure 3-7, Page 7. machine using (2) bar clamps, (4) 3/8-16 x 1-1/2" bolts
Краткое содержание страницы № 9
Item # Part # Description 1 04001-19 Bolt, Hex Head 3/8-16 x 1" 2 04021-09 Nut, Elastic Stop 3/8-16 3 04066-03 Quick Pin 4 423670 Spacer, Hitch 5 451512 Hitch Bracket Weldment 451595 Hitch Bracket Weldment, Floating Hopper Assembly 5 1 2 3 Liquid Cooled 2 Only 1 4 1 Note: 2 Illustration is for reference only. Some parts have been Frame 3 removed for visual purposes and may vary depending 5 on model. FIGURE 3-7 7
Краткое содержание страницы № 10
6.1 GRASS CATCHER REMOVAL INSTRUCTIONS 1. Prepare the work area making sure that it is a REMOVE clean, safe environment. 2. Remove the rubber strap holding the adapter to the blower assembly. See Figure 5-1. 3. Remove the belt from the spindle pulley and the quick pin securing the blower to the discharge mounting bracket. REMOVE 4. Remove the pin and hair pin securing the blower assembly to the mounting bracket on the cutter deck and remove the blower assembly. See FIGURE 5-2 Figure 5-1.
Краткое содержание страницы № 11
MAINTENANCE 5.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS HOURS Break-In 8 20 40 100 200 500 Procedure Comments (First 10) X Check all hardware for tightness X Inspect hose and adapter X Check belt for proper alignment X Inspect fabric bags X *Check screen in hopper Remove debris from screen X Inspect hose and adapter X Inspect fabric bags X Check condition of blower X *Apply grease to blower bearings See figure below X Check belt for proper alignment * Perform these maintenance procedu
Краткое содержание страницы № 12
WARNING INSTALL BELT COVER BEFORE OPERATING MACHINE READ OPERATOR'S MANUAL DANGER ROTATING BLADES AND BLOWER Stop engine before cleaning or removing DO NOT OPERATE MOWER UNLESS GRASS CATCHER OR DISCHARGE GUARD IS INSTALLED GC-STT-V BLOWER HOUSING ASSEMBLY 9 10 11 8 12 48 49 4 1 2 14 50 13 11 9 11 7 10 47 10 14 44 27 14 12 11 15 43 16 42 14 17 26 41 39 18 40 34 15 19 3 25 17 28 20 21 41 38 22 17 35 27 23 5 24 46 14 24 14 29 6 30 33 32 37 31 31 45 47 2005 GC V+ Blower Assembly 35 34 45 36 10 D DA
Краткое содержание страницы № 13
GC-STT-V BLOWER HOUSING ASSEMBLY Ref. Part Ref. Part No. Number Description No. Number Description 1 04067-07 Pin, Ring 2-1/4" Long 27 04019-04 Nut, Serr. Flange 3/8-16 2 481547 Lanyard, Deck Height Pin 28 04001-136 Bolt, Hex Head 3/8-16 x 1-1/2 Gr. 8 3 04019-02 Nut, Serr. Flange 1/4-20 29 483037 Decal, Danger 4 04001-59 Bolt, Hex Head 1/4-20 x 1-1/4" 30 461931 Blower Housing Weldment w/Decals 5 481377 Decal, Blower 31 04003-12 Bolt, Carr. 5/16-18 x 3/4" Gr. 5 6 482080 Decal, Rotatin
Краткое содержание страницы № 14
GC-STT-V BLOWER MOUNTING COMPONENTS UNDER SIDE OF VELOCITY-PLUS CUTTER DECK SHOWN 16 16 10 10 11 5 23 2 26 27 23 25 4 6 28 1 7 24 8 3 25 26 25 6 24 13 9 12 21 14 15 22 15 20 16 18 17 19 RIGHT SIDE OF CUTTER DECK SHOWN 2006 GC-STC-V BMC 12
Краткое содержание страницы № 15
GC-STT-V BLOWER MOUNTING COMPONENTS Ref. Part No. Number Description 1 483225 Belt Cover, GC-STT - 52" 483227 Belt Cover, GC-STT - 61" 2 04029-04 Wingnut, Plastic 3/8" Small 3 483223 Cap, Square Vinyl 4 04021-08 Nut, Elastic Stop 1/4-20 5 461723 Adapter, Blower GC-STT, includes item #7 6 04040-14 Flatwasher, 1/4-.312 x .750 x .065 7 48137-04 Rubber Strap 7-3/4" 8 04001-59 Bolt, Hex Head 1/4-20 x 1-1/4" 9 481625-01 Knob W/Stud, 3/8-16 x 1-1/4" 10 04064-15 Clevis Pin, 5/16 x 1-1/2" 11 04069-03 Pin
Краткое содержание страницы № 16
GC-STT-CSV HOPPER COMPONENTS 16 14 49 50 5 4 3 45 45 41 15 31 43 11 17 51 56 55 40 8 58 59 12 9 25 29 6 33 34 10 53 2 50 49 34 B 49 42 24 55 27 49 6 53 61 43 37 48 60 36 18 38 19 38 53 49 C 34 49 50 20 52 54 72 41 12 49 18 49 49 53 53 60 70 7 A 61 66 58 33 59 28 24 1 49 49 62 10 34 21 38 32 49 57 69 30 38 49 38 35 45 46 22 37 49 49 13 33 36 25 49 21 49 38 C 23 20 33 53 26 58 32 40 44 49 67 59 B 46 64 19 49 53 A 63 29 46 58 60 57 59 28 49 61 61 49 71 65 35 49 46 26 37 68 37 60 2006 GC-STT-CSV Ho
Краткое содержание страницы № 17
GC-STT-CSV HOPPER COMPONENTS Ref. Part Ref. Part No. Number Description No. Number Description 1 483038 Hopper, GC-STT-CS 40 04001-77 Bolt, Hex Head 3/8-16 x 3-1/2" 2 482732 Door, GC-CS 41 04003-04 Bolt, Carriage 5/16-18 x 1" 3 461626 Sweeper Weldment, GC-CS 42 04010-01 Screw, #10-32 x 1/2" 4 482777 Pad, Rubber 43 04017-16 Cap Screw, 5/16-18 x 3/4" Serr. Flan. 5 04090-02 Pop Rivet, 3/16 x .652 44 04017-17 Cap Screw, 5/16-18 x 1" Serr. Flan. 6 423834 Plate, Stiffener 45 04019-03 Nut,
Краткое содержание страницы № 18
GC-STT-CSV DECALS 481039 482275 483044 481327 481377 483037 482080 16
Краткое содержание страницы № 19
LIMITED WARRANTY- COMMERCIAL ACCESSORY Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor. The Scag accessory, including any defective part, must be returned to an Authorized Scag Service Dealer within the warranty period. The expense of delivering the accessory to the dealer for warranty work
Краткое содержание страницы № 20
© 2005 PART NO. 03187 SCAG POWER EQUIPMENT PRINTED 7-2005 DIVISION OF METALCRAFT OF MAYVILLE, INC PRINTED IN USA www.scag.com
