Краткое содержание страницы № 1
Quick N EZ
Foldable Bike Trailer
Owner’s Manual for Model QE100A
Please keep this Owner’s Manual for future reference. If you sell or give this product to someone else, please
include this Owner’s Manual, and ask the new owners to read the instructions completely before operating.
PRIOR TO ASSEMBLY
Please read this Owner’s Manual completely before assembling or operating this product.
Assembly of this product should be carried out by an adult.
Do not return this product
Краткое содержание страницы № 2
FULLY-ASSEMBLED TRAILER PARTS LIST QTY DESCRIPTION QTY DESCRIPTION 1 Frame w/ canopy, sling seat with 5-point 1 2-in-1 rain cover safety harness, tow bar, tow bar coupler, 2 16” rear wheels and rear wheel brackets attached. 1 Safety flag with 3-piece pole and joiners TOOLS REQUIRED FOR ASSEMBLY No tools are required to assemble the trailer. However, for those bikes without a quick-release axle on the rear wheel, an adjustable wrench is required to attach the to
Краткое содержание страницы № 3
ASSEMBLY AND OPERATING INSTRUCTIONS STEP 1 Remove the trailer from the carton and compare the contents with the parts list 1A 1B 1A. Remove all of the contents from inside the carton and place them on a clean flat surface. 1B. Set the wheels to the side and remove the black plastic caps from the ends of the axles. Remove the rain canopy and flag pole assembly from inside the trailer. Make sure that no parts are missing. WARNING Immediately discard all plastic bags and
Краткое содержание страницы № 4
STEP 3 Adjust the sling seat 3A 3B Area of detail in photo 3B 3A. Front view of the trailer with the crossbar secured in place. 3B. To provide more comfort, the sling seat can be adjusted by pulling on one or both sets of straps that run underneath the bottom of the seat. Loosen the straps to allow the trailer to fold flat. STEP 4 Attach the 2-in-1 canopy 4A 4B 4C Snaps 4A. Lay the 2-in-1 canopy over the top of the trailer frame with the large window toward the front.
Краткое содержание страницы № 5
STEP 6 Extend and secure the tow bar 6A 6C 6D 6B Bracket 6A. Lay the trailer on its side with the tow bar at the top and undo the lock pin from the bracket. 6B. Pivot the tow bar all the way forward until the shaft comes to rest in the front part of the bracket. 6C. Insert the lock pin shaft all the way through the forward holes in the bracket and tow bar. 6D. Hook the loop over the end of the shaft and make sure the pin is secure. STEP 7 Attach the wheels to the quick-release bra
Краткое содержание страницы № 6
STEP 9 Install the safety flag 9A 9B 9C Flag pole 9A. Connect the flagpole sections and find the small opening near the top left edge of the canopy. 9B. Slide the end of the flagpole through the opening in the canopy. 9C. Slide the pole all the way down into the flag pole sleeve near the rear corner. WARNING Always use the safety flag when pulling this trailer! STEP 10 Coupler attachment for bikes with rear hub nuts. (Note: If your rear bike tire has a quick-release rear a
Краткое содержание страницы № 7
STEP 12 Coupler attachment for bikes with quick-release rear axles. (Note: If your rear bike tire has two hub nuts please refer to Steps 10 & 11.) 12C 12D 12A 12B 12A. Flip open the quick-release lever, and remove the nut and spring from the opposite side. 12B. Hold the lever and pull the axle skewer with spring out. 12C. Completely remove the skewer but leave the wheel in place. 12D. Slide the coupler plate and tab washer onto the skewer. IMPORTANT! The wide end of the spring sh
Краткое содержание страницы № 8
STEP 14 Proper use of the 5-point safety harness for one or two children 14A 14B WARNING To avoid serious injury children should always wear the seat belt and shoulder straps! 14A. Proper seating position for one child A. Undo the lap belt buckle and seat the child in the center of the trailer/stroller. B. Buckle the lap belt over the child’s lap, and pull the strap until the belt is snug. C. Place the two center shoulder straps over the child’s shoulders, and clip both straps into t
Краткое содержание страницы № 9
Removal of the trailer from the bike 1. Remove children and all cargo from inside the passenger compartment. 2. Unclip the tow bar safety strap from the “D” ring. 3. Loop the strap back around the bike frame tube so that the strap is free of the bike frame. 4. Clip the end of the strap back on to the tow bar “D” ring. 5. Remove the quick-release pin from the tow bar coupler. 6. Slide the tow bar out of the tow bar coupler plate and re-insert the quick-release pin into the holes at the en
Краткое содержание страницы № 10
If you have any questions about the safe use or assembly of this product, please contact one of our Customer Service Representatives at 1-800-242-6110 or by e-mail at info@instep.net. ACCESSORIES FOR YOUR TRAILER Additional Coupler Kits allow you to switch your trailer Turn your trailer into a dual purpose trailer/stroller. The from one bike to another. The Coupler Kit includes the Stroller Conversion Kit includes a front wheel with Q/R coupler plate, tab washer, and Q/R
