Краткое содержание страницы № 1
S/M No. : R63D79S002
Service Manual
Microwave Oven
Model: KOR-63D79S
KOR-63D70S
KOR-63F79S
KOR-63F70S
4 Caution
: In this Manual, some parts can be changed for improving, their
performance without notice in the parts list. So, if you need the
latest parts information,please refer to PPL(Parts Price List) in
Service Information Center (http://svc.dwe.co.kr).
DAEWOO ELECTRONICS CO., LTD.
Краткое содержание страницы № 2
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY (a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other micro- wave source, and make repairs as necessary: (1) Interlock operation, (2) Proper door closing, (3) Seal and sealing surfaces (arcing, wear, and other damage), (4) Damage to or loosening of hinges and lat
Краткое содержание страницы № 3
SAFETY AND PRECAUTIONS 1. FOR SAFE OPERATION Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor cooking and may cause serious bodily injury to the operator. IF ANY OF THE FOLLOWING CONDITIONS EXIST, OPERATOR MUST NOT USE THE APPLIANCE. (Only a trained service personnel should make repairs.) (1) A broken door hinge. (2) A broken door viewing screen. (3) A broken front panel, oven cavity. (4) A loosened door lock. (5) A broken door lock. The d
Краткое содержание страницы № 4
SPECIFICATIONS MODEL KOR-63D79S KOR-63D70S POWER SUPPLY 230V~50Hz, SINGLE PHASE WITH GROUNDING MICROWAVE 1000W 1,200W POWER GRILL CONSUMPTION COMBINATION MICROWAVE ENERGY OUTPUT 700W 800W MICROWAVE FREQUENCY 2450MHz OUTSIDE DIMENSIONS (W x H x D) 465 x 279 x 364 mm (18.3 x 11.0 x 14.4 in) CAVITY DIMENSIONS (W x H x D) 290 x 220 x 306 mm (11.4 x 8.7 x 12.0 in) NET WEIGHT APPROX. 13kg (28.7 Ibs.) TIMER 35 MIN. DUAL SPEED FUNCTION SELECTIONS MICROWAVE POWER SELECTIONS 7 LEVELS CAVITY VOLUME 0.7 Cu
Краткое содержание страницы № 5
EXTERNAL VIEW 1. OUTER DIMENSION 2. FEATURE DIAGRAM 1. SAFETY INTERLOCK SYSTEM 7. ROLLER GUIDE This must always be used for cooking together with the 2. DOORVIEWING SCREEN glass cooking tray. Allos viewing of food. The screen is designed so that light can pass through, but not the microwave. 8. COUPLER This fits over the shaft in the center of the ovens cavity 3. DOOR HOOK floor. This is to remain in the oven for all cooking. When the door is closed, it will automatically lock shut. If door is
Краткое содержание страницы № 6
INSTALLATION 1. Steady, flat location. This microwave oven should be set on a steady, flat surface. 2. Leave space behind and side. All air vents should be kept a clearance. If all vents are covered during operation, the oven may be overheated and, eventually, cause oven failure. 3. Away from radio, and TV sets Poor television reception and radio interference may result if the oven is located close to a TV, radio, antenna, or feeder and so on. 4. Away from heating appliances and water taps Keep
Краткое содержание страницы № 7
OPERATIONS AND FUNCTIONS 1. Connect the main lead to an electrical outlet. 2. After placing the food in a suitable container, open the oven door and put it on the glass tray. The glass tray must always be in place during cooking. 3. Close the door securely. 4. Choose cooking power level by setting V.P.C knob to the desired position. Refer to cookbook for recommended power levels. 5. Determine cooking time. Consult cookbook for recipe timing. Oven light turns on and cooling fan starts to operate.
Краткое содержание страницы № 8
DISASSEMBLY AND ASSEMBLY Cautions to be observed when trouble shooting. Unlike many other appliances, the microwave oven is high-voltage, high-current equipment. It is completely safe during normal operation. However, carelessness in servicing the oven can result in an electric shock or possible danger from a short circuit. You are asked to observe the following precautions carefully. 1. Always remove the power plug from the outlet before servicing. 2. Use an insulated screwdriver and ware rubb
Краткое содержание страницы № 9
4 Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) 1. To remove cabinet 1) Remove three screws on cabinet back. 2) Push the cabinet backward. 2. To remove door assembly 1) Remove two screws which secure the stopper hinge top. 2) Remove the door assembly from top plate of cavity. 3) Re
Краткое содержание страницы № 10
(1) Remove the gasket door from door weld as. (2) Remove the door frame from door weld as. (3) Remove the stopper hinge top from door weld as. (4) Remove the spring and the hook. (5) Remove the barrier screen outer from door frame. (6) Reverse the above steps for reassembly. 4. Method to reduce the gap between the door seal and the oven front surface. (1) To reduce gap located on part ‘A’ Loosen a screws on stopper hinge top, and then push the door to contact the door seal to oven front surface.
Краткое содержание страницы № 11
4 Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr) 5. To remove control panel parts. REF NO. PART CODE PART NAME DESCRIPTION Q’TY REMARK B01 3513405510 KNOB VPC ABS XR-401 H-2938 1 B02 3516725300 CONTROL-PANEL ABS SG-0760D SG-175 1 (KOR-63D7) 3516725350 CONTROL-PANEL ABS SG-0760D SG-17
Краткое содержание страницы № 12
6. To remove high voltage capacitor. 1) Remove a screw which secure the grounding ring terminal of the H.V. diode and the capacitor holder. 2) Remove the H.V. diode from the capacitor holder. 3) Reverse the above steps for reassembly. High voltage circuit wiring 7. To remove magnetron. 1) Remove a screw which secure the magnetron. 2) Remove the magnetron. 3) Reverse the above steps for reassembly. 11
Краткое содержание страницы № 13
NOTE : Never install the magnetron without the metallic gasket plate which is packed with each magnetron to pre- vent microwave leakage. Whenever repair work is carried out on magnetron, check the microwave leakage. It shall 2 not exceed 4mW/cm for a fully assembled oven with door normally closed. 8. To remove wind guide assembly. 1) Remove a screw for earthing. 2) Remove the noise filter from the wind guide. 3) Remove a screw which secure the wind guide assembly. 4) Draw forward the wind guid
Краткое содержание страницы № 14
INTERLOCK MECHANISM AND ADJUSTMENT The door lock mechanism is a device which has been specially designed to completely eliminate microwave radiation when the door is opened during operation, and thus to perfectly prevent the danger resulting from the leakage of microwave. (1) Primary interlock switch When the door is closed, the hook locks the oven door. If the door is not closed properly, the oven will not operate. When the door is closed, the hook push- es the button of the microswitch. Then t
Краткое содержание страницы № 15
TROUBLE SHOOTING GUIDE Following the procedure below to check if the oven is defective or not. 1. Check grounding before trouble checking. 2. Be careful of the high voltage circuit. 3. Discharge the high voltage capacitor. 4. When checking the continuity of the switches, fuse or high voltage transformer, disconnect one lead wire from these parts and check continuity with the AC plug removed. To do otherwise may result in a false reading or damage to your meter. (TROUBLE 1) Door shut, timer set,
Краткое содержание страницы № 16
Does the fan motor work when you shut the door and turn the timer? YES NO Does the oven lamp light? Replace or repair oven lamp, Does the turntable turn? turntable motor. YES Normal reading should be approx. 0Ω NO If microwave do not Check continuity No Continuity Continuity Replace high oscillate, check continuity filament tap (3.3V) Voltage transformer of filament of magnetron. of high voltage. Continuity Poor continuity Continuity in the reverse Check continuity Replace high direction. fi
Краткое содержание страницы № 17
MEASUREMENT AND TEST 1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT Microwave output power can be checked by indirectly measuring the temperature rise of a certain amount of water exposed to the microwave as directed below. PROCEDURE 1. Microwave power output measurement is made with the microwave oven supplied at rated voltage and operated at its maximum microwave power setting with a load of 1000±5cc of potable water. 2. The water is contained in a cylindrical borosilicate glass vessel having a
Краткое содержание страницы № 18
2. MICROWAVE RADIATION TEST WARNING : Make sure to check the microwave leakage before and after repair of adjustment. Always start measuring of an unknown field to assure safety for operating personnel from microwave energy. Do not place your hands into any suspected microwave radiation field unless the safe density level is known. Care should be taken not to place the eyes in direct line with the source of microwave energy. Slowly approach the unit under test until the radiometer reads an appre
Краткое содержание страницы № 19
3. COMPONENT TEST PROCEDURE • High voltage is present at the high voltage terminal of the high voltage transformer during any cooking cycle. • It is neither necessary nor advisable to attempt measurement of the high voltage. • Before touching any oven components or wiring, always unplug the oven from its power source and discharge the capacitor. 1. High voltage transformer (1) Remove connections from the transformer terminals and check continuity. (2) Normal readings should be as follows: Second
Краткое содержание страницы № 20
WIRING DIAGRAM 19
