Краткое содержание страницы № 1
CHAPTER 1
Introducing the Content Router 4430
This chapter provides a basic functional overview of the Content Router 4430 and
describes the Content Router 4430 hardware, major components, and front and
back panel indicators and controls.
This chapter contains the following sections:
• Introduction, page 1-1
� System Hardware Features, page 1-2
� Specifications, page 1-9
� Regulatory Compliance, page 1-10
� Class A Warning Statements, page 1-10
Introduction
Cisco Content Routers are the con
Краткое содержание страницы № 2
Chapter 1 Introducing the Content Router 4430 System Hardware Features System Hardware Features The Content Router 4430 is configured for AC-input power. The default factory configuration comes with one power supply installed. The Content Router 4430 has one internal 18-gigabyte (GB) Ultra2 LVD SCSI hard drive. For network connections, the Content Router 4430 has two 10/100BASE-T Ethernet/Fast Ethernet ports with RJ-45 receptacles. Port Ethernet 0 supports autodetect speed mode and f
Краткое содержание страницы № 3
0 1 2 3 0 1 2 3 LINK 100Mbps LINK 100Mbps CONS ETHERNET 0 ETHERNET 1 LINK 100Mbps LINK 100Mbps SLOT 0 SLOT 1 SCSI LVD ONLY SLOT 0 SLOT 1 CONS ETHERNET 0 ETHERNET 1 Chapter 1 Introducing the Content Router 4430 System Hardware Features Figure 1-1 Content Router 4430—Front Panel Link LED 100Mbps LED Power indicator System indicator Status LEDs Slot 1 Slot 0 Slot 1 LED Slot 0 LED SCSI LVD only port Ethernet ports Console port Cisco Content Router 4430 Hardware Installation Guide 78-12541-01
Краткое содержание страницы № 4
Chapter 1 Introducing the Content Router 4430 System Hardware Features Figure 1-2 Content Router 4430—Back Panel Power switch Power receptacle Ports, Receptacles, and LEDs Table 1-2 describes the front and back panel ports and receptacles. (See the front panel in Figure 1-1 and the back panel in Figure 1-2.) Table 1-2 Ports and Receptacles Item Description Front Panel CONS port This serial port connects to a console. ETHERNET 0 port The Ethernet cable connects to this port. ETHERNET 1 po
Краткое содержание страницы № 5
Chapter 1 Introducing the Content Router 4430 System Hardware Features Table 1-2 Ports and Receptacles (continued) Item Description Slot 0 Bay for hard drive 0. Slot 1 Bay not used. Back Panel Power receptacle The power cord connects to this plug. Power switch This switch toggles between on and off, even though the switch always returns to its initial position after you press it. A power light on the front panel, when lit, indicates that the power is on. Warning To avoid electric shoc
Краткое содержание страницы № 6
Chapter 1 Introducing the Content Router 4430 System Hardware Features Table 1-3 LEDs (continued) Indicator Color State Description Status 0 1 2 3 LEDs Green Steady In a steady display, the state of each LED is constant. (See Table 3-1 for the meanings of steady-state LED variations.) Rolling Reboot has begun. In a rolling display, the four LEDs give the appearance of a light that repeatedly moves from left to right. Cables and Connectors This section describes the cables and connec
Краткое содержание страницы № 7
Chapter 1 Introducing the Content Router 4430 System Hardware Features Figure 1-3 Identifying a Rollover Cable Pin 1 and pin 8 should be the same color Pin 1 Pin 8 Network Cables An Ethernet cable is required to connect the Content Router 4430 to your network. To connect the Content Router 4430 to your network, you must use one of the following types of cables: � Unshielded twisted-pair (UTP) straight-through cable with RJ-45 connectors to connect the Content Router 4430 to a Medium D
Краткое содержание страницы № 8
Chapter 1 Introducing the Content Router 4430 System Hardware Features Ethernet Cable Pinouts The following pinout information for common cable configurations can assist you in purchasing or building replacement cables. Table 1-4 shows the pinout for a straight-through 100BASE-T cable. Table 1-4 Straight-Through 100BASE-T Cable Pinout RJ-45 Pin Signal RJ-45 Pin 1TX+ 1 2TX– 2 3RX+ 3 4— 4 5— 5 6RX– 6 77 88 Table 1-5 shows the pinout for a crossover 100BASE-T cable. Table 1-5 Crossover 100B
Краткое содержание страницы № 9
Chapter 1 Introducing the Content Router 4430 Specifications Specifications Table 1-6 lists hardware specifications for the Content Router 4430 hardware. Table 1-6 Specifications Specification Description Dimensions Height: 1.72 in. (4.37 cm) Width: 17.5 in. (44.45 cm) Depth: 14.13 in. (35.8 cm) Weight 12.5 lb (5.7 kg) AC power � Universal input: 100–127 VAC 200–240 VAC � Frequency: 50–60 Hz � Maximum power: 130W � Current: 120 VAC input with PFC (power factor correction), 1.0A 230 VAC
Краткое содержание страницы № 10
Chapter 1 Introducing the Content Router 4430 Regulatory Compliance Regulatory Compliance Table 1-7 lists regulatory compliance for the Content Router 4430. Table 1-7 Regulatory Compliance Item Description Compliance CE Marking Safety UL 1950 CSA-C22.2 No. 950 EN 60950 IEC 60950 EMC FCC Part 15 (CFR 47) Class A ICES-003 Class A EN 55022 Class A CISPR22 Class A AS/NZ 3548 Class A VCCI Class A EN 55024 Class A Warning Statements Japan VCCI This is a Class A product based on the standard of
Краткое содержание страницы № 11
Chapter 1 Introducing the Content Router 4430 Class A Warning Statements Taiwan BSMI This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Hungary Class A Warning Notice This equipment is a Class A product and should be used and installed properly according to the Hungarian EMC Class A requirements (MSZ EN 55022). Class A equipment is derived for typical commercial establishments
Краткое содержание страницы № 12
Chapter 1 Introducing the Content Router 4430 Class A Warning Statements Cisco Content Router 4430 Hardware Installation Guide 78-12541-01 1-12
