Краткое содержание страницы № 1
Router
MODEL 3606
003646
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Краткое содержание страницы № 2
SPECIFICATIONS Model 3606 Collet chuck capacity 1/4” No load speed (RPM) 30,000/min. Overall length 181 mm (7-1/8”) Net weight 2.5 kg (5.5 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCT
Краткое содержание страницы № 3
5. Avoid body contact with grounded sur- 14. Use safety equipment. Always wear eye faces such as pipes, radiators, ranges and protection. Dust mask, non-skid safety refrigerators. There is an increased risk of shoes, hard hat, or hearing protection must electric shock if your body is grounded. be used for appropriate conditions. Ordinary eye or sun glasses are NOT eye protection. 6. Do not expose power tools to rain or wet conditions. Water entering a power tool will Tool Use and Care increase t
Краткое содержание страницы № 4
24. When servicing a tool, use only identical SERVICE replacement parts. Follow instructions in 23. Tool service must be performed only by the Maintenance section of this manual. qualified repair personnel. Service or main- Use of unauthorized parts or failure to follow tenance performed by unqualified personnel Maintenance instructions may create a risk of could result in a risk of injury. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. W
Краткое содержание страницы № 5
9. Before using the tool on an actual work- 14. Always lead the power supply cord away piece, let it run for a while. Watch for from the tool towards the rear. vibration or wobbling that could indicate 15. Do not smear the tool base carelessly with improperly installed bit. thinner, gasoline, oil or the like. They may 10. Be careful of the bit rotating direction and cause cracks in the tool base. the feed direction. 16. Draw attention to the need to use cutters 11. Do not leave the tool running.
Краткое содержание страницы № 6
FUNCTIONAL CAUTION: DESCRIPTION Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 003651 Adjusting the depth of cut 1 Place the tool on a flat surface. Turn the scale ring until it makes contact with the base. Loosen the clamp screw. Turn the scale ring until the bit just touches the flat surface. Tighten the clamp screw. Place the tool on its side and turn the scale ring counter- 2 clockwise (when viewing the tool from the top) unt
Краткое содержание страницы № 7
To start the tool, move the switch lever to the I (ON) position. To stop the tool, move the switch lever to the O (OFF) posi- tion. ASSEMBLY CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 003669 Installing or removing the bit CAUTION: 1 Install the bit securely. Always use only the wrench provided with the tool. A loose or overtightened bit can be dangerous. 2 Do not tighten the collet nut without inserting a bit, or the collet
Краткое содержание страницы № 8
001985 NOTE: 2 3 Moving the tool forward too fast may cause a poor quality of cut, or damage to the bit or motor. Moving the 1 tool forward too slowly may burn and mar the cut. The proper feed rate will depend on the bit size, the kind of 4 workpiece and depth of cut. Before beginning the cut on the actual workpiece, it is advisable to make a sample 1. Feed direction cut on a piece of scrap lumber. This will show exactly 2. Bit revolving direction how the cut will look as well as enable you to
Краткое содержание страницы № 9
003687 Templet guide (optional accessory) The templet guide provides a sleeve through which the bit passes, allowing use of the tool with templet patterns. 003691 To install the templet guide, loosen the screws on the tool base, insert the templet guide and then tighten the screws. 1 2 3 1. Base plate 2. Templet guide 3. Screw 003695 Secure the templet to the workpiece. Place the tool on the 1 7 templet and move the tool with the templet guide sliding along the side of the templet. 2 NOTE: 3 4
Краткое содержание страницы № 10
003699 Install the trimmer guide on the tool base with the wing bolt (B). Loosen the wing bolt (A) and adjust the distance 1 between the bit and the trimmer guide by turning the fine adjusting screw (1.5 mm or 1/16” per turn). At the desired 2 distance, tighten the wing bolt (A) to secure the trimmer guide in place. When adjusting the guide roller up or down, 5 loosen the wing nut (C). After adjusting it, tighten the wing 3 4 nut (C) securely. 1. Wing bolt (B) 2. Fine adjusting screw 3. Wing bol
Краткое содержание страницы № 11
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. Straight & groove forming bits Edge forming bits Laminate trimming bits Straight guide assembly Trimmer
Краткое содержание страницы № 12
Memo 12
Краткое содержание страницы № 13
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
Краткое содержание страницы № 14
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Краткое содержание страницы № 15
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA FLORIDA MISSOURI PENNSYLVANIA 3707 E. Broadway Rd., Ste. 6 750 East Sample Road 9876 Watson Road 1704 Babcock Blvd. Phoenix, AZ 85040 Pompano Beach, FL 33064 St. Louis, MO 63126-2221 Pittsburgh, PA 15209 (602) 437-2850 (954) 781-6333 (314) 909-9889 (412) 822-7370 CALIFORNIA GEORGIA NEBRASKA PUERTO RICO 41850 Christy St. 4680 River Green Parkway NW 4129 S. 84th St. 200 Guayama St. Fremont, CA 94538-5107 Duluth,
Краткое содержание страницы № 16
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
