Руководство по эксплуатации Custom Autosound Manufacturing USA-630

Краткое содержание страницы № 1

LIMITED WARRANTY
If your product does not work properly because of a defect in material or work-
manship, Custom Autosound Mfg.,Inc. (the Company) will for the length of the
period indicated on the chart below, which starts with the date of original pur-
chase (“Limited Warranty period”), at its option either (a) repair your product with
new or refurbished parts, or (b) replace it with a new or refurbished product. The
Owner's Manual
decision to repair or replace will be made by the company.
Pro

Краткое содержание страницы № 2

Radio Specifications FM Section Tuner Type . . . . . . . . . . . . . . . . . . . . . . . . .PLL IF Frequency . . . . . . . . . . . . .10.7MHZ Frequency Range . . . . . . . . . . .87.5-108 MHz Sensitivity . . . . . . . . . . . . . . . . . . .2.6V Image Rejection . . . . . . . . . . . . . . . . . . . .50dB S/N Ratio . . . . . . . . . . . . . . . . . .60dB Quieting Sensitivity . . . . . . . . . . . . . . . . . .4uV Capture Ratio . . . . . . . . . . . . . . .1.5dB T.H.D . . . . . . . . . . .

Краткое содержание страницы № 3

Introduction Thank you for your purchase of a Custom Autosound radio. This factory made AM/FM receiver is specifically designed and manufactured for your Problem Cause Solution classic special interest vehicle. It is a reflection of over 30 years of customer feedback regarding preferred features,vehicle compatibility, cosmetics and quality components. Power Lead:Red Wire not Check both fuse’s in filter The quality of the components and various parts that are used in our radios were devel- NO Lig

Краткое содержание страницы № 4

General Installation Antenna Noise Thank you for your purchase of this Custom Autosound product! A static or crackle heard through the speakers, usually when the car is running, but sometimes present with the ignition off. If a crackling static if present, follow the steps Owner- Installer: Please review installation instructions and owners manual. outlined below to confirm the antenna as the source of the noise. 1. Start the car engine. Keep in mind that your radio and/or speakers are custom eq

Краткое содержание страницы № 5

Power and Speaker Connections (Refer to Wiring Diagram on page 5.) Noise Suppression A-Main Power-Red Wire B+ All CAM Systems are designed for maximum electrical noise rejection. In some instal- Connect the RED wire (B+) to an accessory fuse that is switched OFF when lations however, electrical noise may affect the quality of sound reproduction. the key switch is in the OFF position and is switched ON when the key switch If noise is present after installing the USA-630, identify the source of th

Краткое содержание страницы № 6

AM/PM Hour Min. Setting The Time Hours Min. The following procedure must be preformed with the radio ON. 1. With the unit on press and release the Time/Frequency PRESS Recall Button (5) so the time is . . displayed. 2. Press and hold in the Time/ Frequency Recall Button (5) for 5 seconds. The hour and minutes should be blinking on the display. Release the button and rotate the Manual Tuning Control (4) gently to the right, the Hour will advance. Rotating the Manual Tuning Control (4) gently

Краткое содержание страницы № 7

CD Changer Operation CD Disc Track Indicator Number Number CONTROLS Track This radio is only compatible with the UP/Down Custom Autosound USA-CD10 10 TURN disc changer. fig.2 1. With CD magazine in place in changer, press the CD button (3) 11 12 3 4 Until CDC is displayed on the Disc Disc Track Track Up Down Up Down LCD. 2. To select a disc press CD up (6) or CD down (7) until the desired disc number is shown on the the LCD display (10). 3. To fast forward through a track, press button (8) tra

Краткое содержание страницы № 8

Sound Controls Receiver Basic Operation Pressing tuning knob (4) will toggle the LCD display in this order - (VOL)-- (BAS)--(TRB)--(BAL L_R)--(FAD F_R). If an adjustment is not made or the tun- 1. Switch the receiver “ON” by depressing the Power ON/OFF Volume control knob (1). ning knob not pressed for 5 seconds the display will revert to regular function. 2. Depress the Band Selector( 3) to the desired position. In the AM mode, AM will be visible in the LCD display (10). In the FM mode, one of