Краткое содержание страницы № 1
PPO-E03
Jp
Instruction Manual
En
Underwater Lens Port for the PT-E Series
Mode d’emploi
Fr
Port d’objectif étanche pour la série PT-E
Bedienungsanleitung
De
Unterwasser-Objektiv-Port für PT-E Serie
Manual de instrucciones
Sp
Puerto de objetivo hermético para la serie PT-E
Cs
Kr
Краткое содержание страницы № 2
Краткое содержание страницы № 3
1
Краткое содержание страницы № 4
2
Краткое содержание страницы № 5
3
Краткое содержание страницы № 6
4
Краткое содержание страницы № 7
5
Краткое содержание страницы № 8
6
Краткое содержание страницы № 9
7
Краткое содержание страницы № 10
8
Краткое содержание страницы № 11
■ Thank you for buying this product. To assure safe and correct use of this product, please read this instruc- tion manual carefully. After reading, store the manual together with the warranty card in a safe, easily accessible place. ■ This product is the Waterproof Lens Port (PPO-E03) designed exclusively for use with the PT-E series of waterproof case. ■ Underwater manual focus (MF) is possible by attaching the provided gear to the MF ring on the camera lens. ■ Note that this will restrict the
Краткое содержание страницы № 12
1 Name of Parts PPO-E03 main body Silicon O-ring (POL-E101) Front cap Rear cap MF Gear Grease for silicone O-ring Pick for O-ring removal 2 Mounting the PPO-E03 on the Waterproof Case This section describes how to mount this product on the PT-E series case. Before Grease applying surface on O-rings mounting, check that no foreign matter is attached to the O-rings, the port mount Threaded thread on the PT-E series case, or the O- section ring contact surfaces. Apply a thin layer of
Краткое содержание страницы № 13
3 Dismounting the PPO-E03 If any water is on the product, wipe it completely away and make sure that the product is dry. Holding the PT-E series case firmly with one hand, loosen the PPO-E03 by turning it about 90 degrees counterclockwise. If the PPO-E03 is attached too tightly to turn, wrap it with a piece of rubber or similar non-slip material. After loosening the PPO-E03, point its lens downward and turn it further counterclockwise until it is separated from the PT-E series case. Be car
Краткое содержание страницы № 14
4 Attaching the Gear to the Lens To control the camera lens’s manual focus (MF) operation, the provided gear must be attached to the MF ring on the lens. * Note that this will restrict the rotation range of the MF ring to within 180°. Confirm the position of the gear’s lock dial and hinge. Turn Hinge the lock dial counterclockwise to release the lock and open the gear. Open Lock dial Open the gear all the way, place it on the lens and adjust the rotation direction of the gear. At this time,
Краткое содержание страницы № 15
5 Loading the Camera and Lens After attaching the gear to the camera’s lens, insert the camera and lens into the PT-E series case on which the PPO-E03 is mounted. Screw the camera table provided with the PT-E Remove the eyecup from the camera’s viewfind- series case firmly into the bottom of the cam- er. If a lens cap or filter is attached to the lens or era. the strap is attached to the camera, remove them as well. Power switch dial Mode dial knob Zoom/MF dial Pull out the zoom/MF dial furt
Краткое содержание страницы № 16
After inserting the camera, turn the PT-E series Push in the PT-E series case’s power switch case’s camera table lock lever all the way clock- dial and mode dial knob. Turn the power switch wise to lock the camera table. Then, push in the dial and mode dial knob and confirm that they zoom/MF dial on the PT-E series case and can control the camera power ON-OFF and engage it with the gear attached to the lens. mode switching. Connect the hot shoe mount Turn the zoom/MF dial to confirm that it
Краткое содержание страницы № 17
6 Maintenance For safe use of this product, always perform maintenance after each diving session. For details, refer to “Handling After Shooting” and “Maintaining the Waterproof Function” in the PT-E series case instruction manual. Apply the same procedures to this product. After shooting, remove the inserted cam- After making sure that the PT-E series era and lens, then re-seal the empty case is completely dry, dismount this case and immerse it in tap water to product from the case. remove
Краткое содержание страницы № 18
7 Specifications Applicable case : PT-E series Applicable lens : ZUIKO DIGITAL ED 50mm F2.0 Macro Main materials Main body : Aluminum. Lens window : Chemically reinforced glass. O-rings : Silicon rubber. MF gear : Polycarbonate resin. Front cap : NBR rubber. Rear cap : Polyethylene resin. Withstanding pressure : Water depth of 60 m (200 ft) Dimensions : Max. diameter 108 mm x Depth 87 mm Weight : 420 g (excluding the conversion lens) Note) We reserve the right to change the external appearance
Краткое содержание страницы № 19
■ Nous vous remercions d’avoir acheté ce produit. Veuillez lire attentivement ce mode d’emploi et utiliser correctement et de façon sûre le produit. Après lecture, veuillez conserver ce manuel ensemble avec la carte de garantie. ■ Ce produit est le port d’objectif étanche (PPO-E03) pour l’utilisation avec un caisson étanche de série PT-E. ■ La mise au point manuelle (MF) pendant la prise de vue sous-marine est rendue possible en fixant le mécanisme, fourni avec ce produit, à la bague MF de l’obj
Краткое содержание страницы № 20
1 Nomenclature des pièces Corps principal PPO-E03 Joint silicone (POL-E101) Bouchon avant Bouchon arrière Mécanisme pour MF Graisse pour joint silicone Pic pour retirer les joints 2 Montage du PPO-E03 sur le caisson étanche Cette section décrit comment monter ce produit sur un caisson étanche de série Application de graisse sur la surface des joints PT-E. Avant le montage, vérifier qu’il n’y a aucun corps étranger collé sur les joints, le filetage de monture du port sur le cais- Pa
