Краткое содержание страницы № 1
AT-9000/28
Managed Layer 2
GE ecoSwitch
Installation Guide
613-001058 Rev. A
Краткое содержание страницы № 2
Copyright 2008 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesis, Inc. reserves the right to make changes in specifications and other informat
Краткое содержание страницы № 3
Electrical Safety and Emissions Standards This product meets the following standards. U.S. Federal Communications Commission Radiated Energy Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy a
Краткое содержание страницы № 4
Translated Safety Statements Important: The indicates that a translation of the safety statement is available in a PDF document titled “Translated Safety Statements” (613-000990) posted on the Allied Telesis website at www.alliedtelesis.com. This document is also included with the documentation CD that is shipped with the product. 4
Краткое содержание страницы № 5
Contents Contents ...............................................................................................................................................................................5 Preface ..................................................................................................................................................................................7 Safety Symbols Used in this Document.................................................................................
Краткое содержание страницы № 6
Contents Chapter 3: Troubleshooting ..............................................................................................................................................41 Power LED is Off ..................................................................................................................................................................42 Twisted Pair Port Link LED is Off........................................................................................................
Краткое содержание страницы № 7
Preface This guide provides the hardware installation instructions for you to install the AT-9000/28 Gigabit Ethernet ecoSwitch. This preface contains the following sections: “Safety Symbols Used in this Document” on page 8 “Where to Find Web-based Guides” on page 9 “Contacting Allied Telesis” on page 10 7
Краткое содержание страницы № 8
Preface Safety Symbols Used in this Document This document uses the safety symbols defined in Table 1. Table 1. Safety Symbols Symbol Meaning Description Caution Performing or omitting a specific action may result in equipment damage or loss of data. Warning Performing or omitting a specific action may result in electrical shock. 8
Краткое содержание страницы № 9
AT-9000/28 Gigabit Ethernet ecoSwitch Installation Guide Where to Find Web-based Guides The installation and user guides for all Allied Telesis products are available in portable document format (PDF) on our web site at www.alliedtelesis.com. You can view the documents online or download them onto a local workstation or server. 9
Краткое содержание страницы № 10
Preface Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales or corporate information. Online Support You can request technical support online by accessing the Allied Telesis Knowledge Base from the following web site: www.alliedtelesis.com/support. You can use the Knowledge Base to submit questions to our technical support staff and review answers to previously asked questions. Email and For Technical Support via email
Краткое содержание страницы № 11
Chapter 1 Overview The AT-9000/28 Gigabit Ethernet ecoSwitch is designed to simplify the task of creating or expanding an Ethernet, Fast Ethernet, or Gigabit Ethernet network. This chapter contains the follows sections: “Switch Features” on page 12 “Front and Back Panels” on page 13 “Gigabit Ethernet Ports” on page 14 “LEDs” on page 16 “Ethernet Switching Basics” on page 21 11
Краткое содержание страницы № 12
Overview Switch Features The features of the AT-9000/28 Gigabit Ethernet ecoSwitch include: 28 10/100/1000Base-T copper ports with RF-45 connectors 4 SFP slots RS232 Console port with RJ-45 connector Port status LEDs Low power mode push-button ecoSwitch MODE selection switch Auto MDI/MDI-X on the twisted pair ports IEEE 802.3i, 3u, and 3z compliant IEEE 802.3x flow control in full-duplex operation; back pressure in half-duplex operation and pause frame flow control in full duplex mode
Краткое содержание страницы № 13
AT-9000/28 Gigabit Ethernet ecoSwitch Installation Guide Front and Back Panels Figure 1 illustrates the front panel of the AT-9000/28 Gigabit Ethernet ecoSwitch. 25 27 25R 27R AT-9000/28 Gigabit Ethernet Switch with 4 Combo SFP Ports MODE COL CONSOLE PWR SYS SPD DUP ACT SELECT 26 28 26R 28R RS-232 1451 Figure 1. AT-9000/28 Gigabit Ethernet ecoSwitch Front Panel Figure 2 illustrates the back panel of the AT-9000/28 Gigabit Ethernet ecoSwitch. 100-240 VAC~ 1452 Figure 2. AT-9000/28 Gigabit Eth
Краткое содержание страницы № 14
Overview Gigabit Ethernet Ports The AT-9000/28 Gigabit Ethernet ecoSwitch features 24 twisted pair 10/ 100/1000Base-T ports, and four combo SFP/copper ports. Twisted Pair The twisted pair ports feature 8-pin RJ-45 connectors. (For the port pinouts, refer to “10/100/1000Base-T Twisted Pair Port Connectors” on Ports page 48.) The ports on the AT-9000/28 Gigabit Ethernet ecoSwitch are 1000Base-T, 100Base-TX and 10Base-T compliant and are capable of 1000 megabits per second (Mbps), 100 Mbps and
Краткое содержание страницы № 15
AT-9000/28 Gigabit Ethernet ecoSwitch Installation Guide Uplink Ports The switch has four combo pairs of uplink ports, each consisting of one slot for a SFP transceiver and an redundant 10/100/1000 Base-T twisted pair port .The ports are numbered 25 through 28 on the AT-9000/28 Gigabit Ethernet ecoSwitch. The twisted pair ports in each of the combo pairs are identified with the letter “R” for “Redundant” as part of their number on the front faceplate of the unit. In each combo pair, you ca
Краткое содержание страницы № 16
Overview LEDs System LEDs There are two system LEDs, the Power LED and SYS LED as shown in the following figure: PWR SYS Figure 3 Power and System LEDs The power supply port and system LED indications are described in the following table: Table 2 Power Supply LED Indications LED LED Description Description Indication Power Green System is powered up (power on) Off System is not powered up (power off) SYS Green System is operational 16
Краткое содержание страницы № 17
AT-9000/28 Gigabit Ethernet ecoSwitch Installation Guide RJ-45 Port LEDs The RJ-45 port LEDs for the AT-9000/28 Gigabit Ethernet ecoSwitch are illustrated in Figure 4. On each port, the left LED indicates the Link status & MODE Switch and the right LED indicates the status of a selected MODE. LINK MODE LED LED MODE LINK LED LED 1467 Figure 4. RJ-45 Port LEDs LINK LED The RJ-45 LINK LED function is described in Table 3: Table 3. RJ-45 LINK LED Indication RJ-45 LED Port Description Indication
Краткое содержание страницы № 18
Overview The RJ-45 Port Mode LED indications are described in Table 4. Each port MODE is selected by the MODE SELECT switch . Table 4 RJ-45 Port LED MODE Indications RJ-45 Port LED Port Description MODE Indication LED Solid Green Data collisions are occurring on the port. COL Off No data collisions are occurring on the port. Solid Green Link is established at 1000Mbps. Solid Link is established at 100Mbps. SPD Right Amber LED Off Link is established in 10Mbps. Solid Green A Full Duplex m
Краткое содержание страницы № 19
AT-9000/28 Gigabit Ethernet ecoSwitch Installation Guide SFP LEDs The SFP LINK LEDs are illustrated in Figure 6 and their function is described in Table 5: 25 27 26 28 LINK LEDs Figure 6. SFP LINK LEDs Table 5. SFP LINK LED Indication LED Description Indication Solid Green A link is established on the port. Off No link is established on the port. 19
Краткое содержание страницы № 20
Overview ecoSwitch The ecoSwitch button on the front panel of the AT-9000/28 Gigabit Ethernet ecoSwitch enables the low power mode. This mode allows you to conserve power by turning off the port and MODE LEDs when they are not required. To toggle the LEDs on or off, press the ecoSwitch button illustrated in Figure 7 next to the SELECT MODE button. The LPM feature does not affect the network operations of the switch or the Power and Sys LEDs. AT-900 Gigabit Etherne MODE COL SPD DUP ACT SELE
