Краткое содержание страницы № 1
Installat Ion Instruct Ions
®
Preference Wall Mount r ange Hood
for use with model: PHW
Part No. 101745 Rev. B
Preliminary
For Review Only
Краткое содержание страницы № 2
Краткое содержание страницы № 3
table of contents Before You Begin... ..................................................1 Installation Instructions ....................................... 6-11 Install the Electrical Connection ....................................... 6 Important Safety Instructions ................................. 1-3 Install the Chimney Mounting Bracket ............................. 6 What You Need to Know About Safety Instructions ......... 1 Install Blower Mounting Bracket ..............................
Краткое содержание страницы № 4
IMPortant safetY InstructIons general safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your range hood, follow basic safety precautions, including the following: WARNING 1. Do not install or operate this hood if it has been damaged, dropped, has damaged electrical conduit or wires or is not working properly. If the product is damaged when received, immediately contact the dealer or builder. 2. Use this range hood only for its intended purpose a
Краткое содержание страницы № 5
IMPortant safetY InstructIons WARNING 21. TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE: a. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. b. NEVER PICK UP A FLAMING PAN - you may be burned. c. DO NOT USE WATER, including wet dish cloths or towels - a violent steam explosion may result. d. Use a fire ext
Краткое содержание страницы № 6
PreParIng for InstallatIon Verify the Package contents Unpack the parts box and verify that all required components have been provided. If any item is missing or damaged, please contact the dealer immediately. Do not install a damaged or incomplete appliance. Blower assembly with filters A Chimney assembly (2 piece) B Chimney mounting bracket C B Blower assembly mounting bracket D Tempered glass hood* E Mounting and assembly hardware F Mounting hardware template G Use and care manual
Краткое содержание страницы № 7
PreParIng for InstallatIon • To prevent back-drafts, a electrical Power supply damper at the duct outlet may also be required. • When planning new duct WARNING work, always look for • Observe all governing codes and ordinances during the shortest, most direct planning and installation. Contact your local building route to the outside. department for further information. Venting can be done through the roof or electrical specifications directly through the back It is the owner’s respo
Краткое содержание страницы № 8
InstallatIon InstructIons 4. Locate the chimney mounting bracket and position it WARNING against the ceiling as shown. Center it on the vertical • Do not install the range hood unless the electrical center line drawn on the wall. service provided meets the range hood specifications. ANCHOR • Observe all governing codes and ordinances during CHIMNEY planning and installation. Contact your local building MOUNTING department for further information. BRACKET • A qualified technician must comp
Краткое содержание страницы № 9
InstallatIon InstructIons 5. Drill the mounting holes... Install the duct Work If mounting the hood to brick or masonry: • Drill five 5/16” X 1 1/2” holes in the locations IMPORTANT - The installed duct work must: marked. • Be centered on the vertical center line drawn on the • Insert five of the provided wall anchors into the five wall. holes. The anchors provided are for attaching the • Fit flush into the half circle on the chimney mounting hood to masonry or brick only. bracket, if the d
Краткое содержание страницы № 10
InstallatIon InstructIons Hanging the blower assembly 3. Insert two provided machine screws into the two holes above the mounting bracket on the blower assembly WARNING and tighten into place. • Do not use screws to attach the duct work to the 4. Insert two machine screws through the front of the exhaust outlet. Use duct tape only. Screws may mounting bracket and tighten into place. prevent the damper flaps on the top of the hood from opening. 5. Insert two machine screws through the side
Краткое содержание страницы № 11
InstallatIon InstructIons electrical connection Install the chimney IMPORTANT: Be careful not to pinch the electrical wires WARNINGS while installing the chimney. • To avoid electrical shock or fire hazard, make sure 1. Remove the protective plastic covering from both the power supply at the fuse or junction box is turned pieces of the chimney assembly. Do not remove the off before proceeding with final installation. protective tape strips from the inside of the chimney. • Improper connec
Краткое содержание страницы № 12
InstallatIon InstructIons chimney Installation (cont.) Install the Hood 5. Carefully put the chimney over the blower assembly, WARNING taking care not to scratch the surfaces. Make sure the wiring is tucked in behind the chimney. • Attaching the glass range hood requires two people. Do not attempt to lift the hood without assistance. 6. Lock the tabs inside the chimney bottom into the slots on the bottom of the blower assembly. 1. Locate the hood mounting hardware. It consists of: - 4 thu
Краткое содержание страницы № 13
InstallatIon InstructIons Verify Proper operation Installation checklist 1. Turn on power at the junction or fuse box. WARNING 2. If the control panel is not lit, turn on the main power • To ensure a safe and proper installation, the following switch located next to the light fixture on the underside checklist should be completed by the installer to of the hood. ensure that no part of the installation has been 3. Touch the light key. Verify that all the lights come on. overlooked. 4. Touc
Краткое содержание страницы № 14
notes
Краткое содержание страницы № 15
Краткое содержание страницы № 16
Specifications contained within are subject to change without notice. No liability is assumed by Dacor for changes in specifications. Web Site: www.Dacor.com Phone: (800) 793-0093 Copyright © 2007 Dacor, All rights reserved.
